LevelOne FEP-0840 User manual

http://www.level1.com 1
FEP-0840
8-Port Web Smart PoE Switch
Quick Guide
&
User Manual
V1.0
Digital Data Communications Asia Co., Ltd.
http://www.level1.com

http://www.level1.com
2
Quick Guide
Step1. Connect POE SWITCH with AC power cord to 100~240VAC.
Step2. Connect the PoE AP device to LAN port 1, and your PC to LAN port 8 as the
following connection.
Step3. Turn on the power switch, it will light on the PWR LED, and perform self-
diagnostic test. It takes about 10 seconds to complete the process.
Step4. Set your PC IP address to 192.168.2.100 (same subnet 192.168.2.x as the web
management).
Step5. Enter "192.168.2.1" (default IP address of Web management) from PC web browser.
The web management will display the following login page
Enter “admin”for user ID, “system”for password, and click the OK
button to login to the Web management.
Note: the user ID and password fields are case-sensitive.

http://www.level1.com
3
Step6. Click the icon “PoE”, and then select “PoE Setting”.
Step7. Select “Enable”and click on Port No.1and Update to power on the connected PoE AP
device for Port 1. You may also click “PoE Scheduling”to select time schedule for
Power on/off scheduling control.
Step8. Refer to Chapter 4 forfurther networking configurations.
** Note:
Problems in setting up the web smart PoE switch?
Please refer to the last chapter for troubleshooting.

http://www.level1.com
4
Table of Contents
1 Introduction ................................................................................................................ 7
2 Features....................................................................................................................... 8
2.1 Power on Switch................................................................................................ 8
2.2 LED Indicators.................................................................................................. 8
3 Switch Installations..................................................................................................... 9
3.1 Package Contents .............................................................................................. 9
3.2 Hardware Overview.......................................................................................... 9
3.3 Preparations for Site Installation................................................................... 11
3.4 Desktop Installation ........................................................................................ 11
3.5 Cabling Requirements .................................................................................... 12
3.6 Power Connection ........................................................................................... 13
3.7 Installation Steps............................................................................................. 13
3.8 Reset to Default................................................................................................ 14
4 Web Management..................................................................................................... 16
4.1 Setup your computer for Web management................................................. 16
4.2 Web management............................................................................................ 19
4.3 Administrator.................................................................................................. 20
4.3.1 AuthenticationConfiguration............................................................ 20
4.3.2 System IP Configuration.................................................................... 21
4.3.3 System Status ...................................................................................... 21
4.3.4 Load Default Setting........................................................................... 22
4.3.5 Firmware Update................................................................................ 22
4.4 PoE.................................................................................................................... 23
4.4.1 PoE Setting.......................................................................................... 23
4.4.2 PoE Power Delay ................................................................................ 24
4.4.3 PoE Scheduling................................................................................... 25

http://www.level1.com
5
4.5 Port Management............................................................................................ 26
4.5.1 Port Configuration ............................................................................. 26
4.5.2 Port Mirroring.................................................................................... 27
4.5.3 Bandwidth Control............................................................................. 28
4.5.4 Broadcast Storm Control................................................................... 34
4.6 VLAN Setting................................................................................................... 35
4.6.1 VLAN Mode........................................................................................ 35
4.6.2 VLAN Member................................................................................... 36
4.7 Per Port Counter............................................................................................. 39
4.8 QoS Setting....................................................................................................... 40
4.8.1 Priority Mode...................................................................................... 40
4.8.2 Class of Service Configuration .......................................................... 41
4.9 Security............................................................................................................. 43
4.9.1 MAC Address Binding....................................................................... 43
4.9.2 MAC Address Scan............................................................................. 44
4.9.3 TCP/UDP Filter .................................................................................. 44
4.9.4 Web Management Filter.................................................................... 45
4.10 Spanning Tree.................................................................................................. 45
4.10.1 STP Bridge Settings............................................................................ 46
4.10.2 STP Port Settings................................................................................ 46
4.10.3 Loopback Detection Settings............................................................. 46
4.11 Trunk Setting................................................................................................... 48
4.12 DHCP Relay Agent.......................................................................................... 49
4.13 NTP Setting...................................................................................................... 49
4.14 Backup/Recovery............................................................................................. 50
4.15 Miscellaneous................................................................................................... 51
4.16 Logout............................................................................................................... 51
AppendixA: Product Specifications
................................................................................ 52

http://www.level1.com
6
Appendix B: Troubleshooting
.......................................................................................... 54
B.1 Can NOT Access Web Page?.......................................................................... 54
B.2 Forget IP Address, User ID, and Password?................................................ 54

http://www.level1.com 7
1 Introduction
The POE SWITCH is an 8-Port Web-Smart Midspan PoE Switch with power on/off
scheduling control. The web smart features are designed to deliver high levels of
performance that are commensurate with Fast Ethernet networking, and to provide simple
and easy installation in an environment where the power over Ethernet (PoE) are required
for remote PoE devices.
The web smart switch provide 10/100Mbps Fast Ethernet connections with many
networking capabilities per port basis including Security, QoS service, Bandwidth Control,
Spanning Tree Protocol, VLAN, SNMP settings, and PoE functions.
The power over the Ethernet ports are all turned off initially, and can be turned on per port
basis through the web management to power on the corresponding remote PoE device. The
powered PoE device can be any equipment of IEEE 802.3af and 802.3at PoE device, such as
WiFi AP, IP camera, IP Phone, etc.
Each port can deliver up to 15 Watt (or optional 30Watt) to the corresponding remote PoE
device. Request of more power from remote PoE device may result in a power failure due
to activation of Over-Current-Protection (OCP) circuit.
The POE SWITCH can be installed in a rack mount chassis where space is limited. The
optional rack mount kit can be purchased separately from you local dealer for rack mount
installation.
The rest of this user manual will help you to uncover most of the web smart features
with step-by-step instructions illustrated on web pages.

http://www.level1.com
8
2 Features
The POE SWITCH web smart PoE switch is equipped with an 8-port RJ45 connector for Fast
Ethernet, and the corresponding LED indicators for each port. In addition, a built-in push
button is provided for default reset, which is useful to reset back to the default IP address,
user ID, and password. The features are as the following
RJ45 x 8 for WAN and LAN ports with PoE capability
Max. 15Watt (optional 30Watt) per port basis
Passive power compatible with IEEE802.3af and 802.3at PoE devices
Networking configurations by Web Management
16+1 LED Indicators: LAN, PoE (for 8 ports) + PWR (for system power)
Built-in push button for default reset
AC power on/off switch
OVP, OCP, OTP protections
2.1 Power on Switch
The POE SWITCH is equipped with an internal power supply to operate with 100~240 VAC,
50 ~ 60 Hz. The AC power cord connector is at the rear panel next to the power on/off
switch. Turning on the power switch, it will first perform “self-diagnostic”test, and take
about 10 seconds to complete the process.
2.2 LED Indicators
LED Status Table
LED
Status
Descriptions
PoE
ON
The PoE function is enabled.
OFF
The PoE function is disabled.
Power
ON
System power is on.
OFF
System power is off.
10/100M
ON
LAN Port is in connection.
OFF
No Ethernet connection.
Flashing
Data is transmitting or receiving

http://www.level1.com 9
3 Switch Installations
This chapter lists the package contents, and describes the hardware and detailed procedures for
installation of the web management switch. For a quick setup, please refer to the quick guide
at the beginning of this manual.
3.1 Package Contents
Make sure that you have all the necessary accessories that come with your package, before you
start the installation of the web management switch.
After unpacking and taking out the entire package contents, please check whether you have
got the following items:
POE SWITCH Unit
One AC Power Cord
One CD-ROM for Quick Guide & User‟s Manual
If any of these above items is missing or damaged, please contact your local dealer for
replacement.
3.2 Hardware Overview
Front Panel
The 8 ports of RJ-45 connector are on the front panel of the web smart switch with the
corresponding LED indicators. The built-in push button for default reset is next to the PWR
LED indicator, and can be easily accessed by a pencil or a ball pen.

http://www.level1.com
10
LED Indicators:
LED indicators display the network connection and PoE status of the switch.
100BASE-TX Fast Ethernet with PoE Ports (Port 1~8):
These ports are with passive PoE capabilities, and will supply power to the connected PoE
device under the control of the web management. This feature allows users to freely and
safely mix legacy and PoE compatible devices on their network.
All the 8 ports support network speeds of either 10Mbps or 100Mbps, and can operate in half-
and full- duplex transfer modes. These ports also support the automatic MDI/MDIX
crossover detection function to provide “plug and play”capability.
Reset Button
The Reset button is used to reset all the setting back to the factory default values. Make sure
that all the settings of the switch are taken down, or all the previous settings will be erased
after pressing the “Reset” button.
The Rear Panel
The 3-pronged power plug is placed at the rear panel of the switch shown as below.