LevelOne IES-0853 User manual

IES-0853
4 x 802.3at PoE + 3 FE + 1 MM SC Web Smart Switch -40 to 75C, DIN-rail
User Manual
v1.00-1206

IES-0853 UserManual Page2
Preface
This manual describes how to install and use the HardenedWeb-Smart PoE & High Power
PoE Ethernet Switch.This switch introduced here is designed to deliver full scalability with
web-based management functions. Capable of operating at temperature extremes of
-40°C to +75°C, this is the switch of choice for harsh environmentsconstrained by space.
Port 1 to port 4 on this switch supports IEEE802.3af Power over Ethernet (PoE) Power
Sourcing Equipment (PSE) and can detect an IEEE802.3af compliant Powered Device (PD).
Using external 48VDC power inputs throughTerminal Block or Power Jack, data and power
can be transmitted to aPowered Device (PD) over the same twisted-pair Ethernet cable
through port 1 to port 4 on the switch.
Port 1 to port 4 on this switch also supports High Power PoE Power Sourcing Equipment
(PSE) and can detect a Powered Device (PD). Using external 55VDC power inputs through
Terminal Block or Power Jack, data and power can be transmitted to a Powered Device (PD)
over the same twisted-pair Ethernet cable through port 1 to port 4 on the switch.
To get the most out of this manual, you should have an understanding of Ethernet
networking concepts.
In this manual, you will find:
Features on the HardenedWeb-Smart PoE Ethernet Switch
Illustrative LEDfunctions
Installation instructions
Management Configuration
Specifications

IES-0853 UserManual Page3
Table of Contents
OVERVIEW...........................................................................................................................4
HARDENEDWEB-SMART POEETHERNET SWITCH..............................................................................................4
FEATURES...............................................................................................................................................................5
PACKAGE CONTENTS.............................................................................................................................................5
FRONT PANEL DISPLAY.........................................................................................................................................6
POWERINPUT........................................................................................................................................................7
DINRAIN MOUNT.................................................................................................................................................8
10/100BASE-TXCONNECTOR............................................................................................................................9
CONNECTINGTOYOURNETWORK....................................................................................................................10
CableType&Length.............................................................................................................................10
Cabling.....................................................................................................................................................10
WEB MANAGEMENT .........................................................................................................11
DEFAULTSETTING ..............................................................................................................................................11
LOGGING ONTOTHE SWITCH.............................................................................................................................12
BROWSER INTERFACE .........................................................................................................................................13
PoE............................................................................................................................................................14
HighPowerPoEOperation.................................................................................................................15
PortBasedVLAN....................................................................................................................................16
Priority......................................................................................................................................................17
DiffServCodePoint..............................................................................................................................18
SystemSetup..........................................................................................................................................19
FirmwareUpgrade................................................................................................................................20
SPECIFICATIONS ...............................................................................................................21

IES-0853 UserManual Page4
Overview
HardenedWeb-Smart PoE Ethernet Switch
LevelOne IES-0853 Industry Ethernet Switch provides 4 PoE ports of 10/100Base-TX plus 3
ports of 10/100Base-TX Ethernet plus 1 port 100FX Multimode SC fiber to enable high
speed network at mission-critical environment.This device is designed to be mounted on
an industry standard DIN-rail, plus the clearly visible status LEDs provide simple
monitoring of port link activity.
High Reliability
All components are built to withstand harsh environment applications without
compromise where humidity, temperature variation and even shock vibration are
concerns, including Electric & Utility, Critical Infrastructure,Transportation and
Surveillance Security.This device operates under -40 to 75 Celsius (-40 to 167 Fahrenheit)
temperature.
Web Management
Web-based GUI management features implementation of Port-basedVLAN, IEEE802.1p
QoS, Prioritised DSCP, set up Admin Password with ease.Plus, the Power over Ethernet
ports can be On / Off and limits the powerbudget remotely
Power over Ethernet
This switch is Power Sourcing Equipment (PSE), and it is fully complied with IEEE 802.3at
PoE standard at maximum 30W powerbudget per port. It helps to save infrastructure
wiring costs dramatically by eliminating electric wiring and less UPS needed. Also, it is
compatible with IEEE802.3af standard PD devices.
Safety
This device has been tested under UL508 standard for Industrial Control Equipment to
highly reliability and safety measurement to ensure field hardened, especially for the harsh
environment.

IES-0853 UserManual Page5
Features
Complies with NEMATS1/TS2 Environmental requirements such as temperature, shock,
and vibration for traffic control equipment.
Complies with EN61000-6-2 & EN61000-6-3 EMC Generic standard immunity for
Industrial environment.
Manageable viaWeb browser interface.
Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
High Power PoE design up to 30W (enhancement of IEEE802.3af PoE).
Supports IEEE802.3/802.3u/802.3x.Auto-negotiation: 10/100Mbps-full/half-duplex;
Auto MDI/MDIX.
100Base-FX: Multi mode SC or ST type, Single mode SC or ST type.100Base-BX:WDM
Single mode SC type.
Supports 1024 MAC addresses. Provides 1M bits memory buffer.
Store-and-forward mechanism.
Full wire-speed forwarding rate.
Alarms forpower and port link failure by relay output.
PoE: Redundant 48VDCTerminal Block power inputs and 48VDC DC JACK power input
for 15.4W per PoE port. Operating voltage and Max. current consumption: 1.5A @
48VDC. Power consumption: 72W Max.
High Power PoE: Redundant 55VDCTerminal Block power inputs and 55VDC DC JACK
power input for 30W per High Power PoE port. Operating voltage and Max. current
consumption: 2.3A @ 55VDC. Power consumption: 130W Max.
-40℃to 75℃(-40℉to 167℉) operating temperature range.Tested for functional
operation @ -40℃to 85℃(-40℉to 185℉).Web-Smart function operating temperature
@-20℃to 85℃(-4℉to 185℉).
Reset button on front panel.
Front panel port status LEDs.
Hardened aluminum case.
Supports DIN-Rail, Panel, or Rack Mounting installation.
Package Contents
When you unpack the product package, you shall find the itemslisted below. Please
inspect the contents,and report any apparent damage or missing items immediately to
your authorized reseller.
IES-0853 HardenedWeb-Smart High Power PoE Ethernet Switch
Quick Installation Guide
CDUserManual

IES-0853 UserManual Page6
Front Panel Display
LED
Status
Description
PW 1,2,3
Steady
Power On
Off
Power Off
10/100Base-TX or 100Base-FX/BX
LNK/ACT
Steady
Network connection is established
Flashing
Transmitting or Receiving data
PoE
(High Power)
Steady
Power Device (PD) is connected
Off
Power Device (PD) is disconnected

IES-0853 UserManual Page7
Power Input
Terminal Block
PW1
+
48, 55VDC (High Power)
Power Ground
PW2
+
48, 55VDC (High Power)
Power Ground
PW3
DC Jack
48, 55VDC (High Power)
Earth Ground
Relay Output
0.1A @ 24VDC
*Warning signaldisable for following:
1. The relay contact closes if Power1 and Power2 are both failed but Power3
on.
2. The relay contact closes if Power3 is failed but Power1 and Power2 are
both on.
DC Jack
PW3
DC Jack
48, 55VDC (High Power)
Special Note:
The relay output is normal open position when there is no power to the switch. Please do
not connect any power source to this terminal to prevent shorting your power supply.

IES-0853 UserManual Page8
DIN rain Mount
Fix the DIN rail attachment plate to theback panel of the switch.
Installation: Place the switch on the DIN rail from above using the slot. Push the front of
the switch toward the mounting surface until it audibly snaps into place.
Removal: Pull out the loweredge and then remove theswitch from the DIN rail.

IES-0853 UserManual Page9
10/100Base-TX Connector
The following lists the pin-out of 10/100Base-TX ports.
Pin
PoE Port (1 to 4)
Standard Port (5)
1
OutputTransmit Data +
Input Receive Data +
2
OutputTransmit Data -
Input Receive Data -
3
Input Receive Data +
OutputTransmit Data +
4
Positive (VCC+)
NC
5
Positive (VCC+)
NC
6
Input Receive Data -
OutputTransmit Data -
7
Negative (VCC-)
NC
8
Negative (VCC-)
NC

IES-0853 UserManual Page10
Connecting toYour Network
Cable Type & Length
It is necessary to follow the cable specifications below when connecting the switch to your
network. Use appropriate cables that meet your speed and cabling requirements.
Cable Specifications
Speed
Connector
Port Speed
Half/FullDuplex
Cable
Max.
Distance
10Base-T
RJ-45
10/20 Mbps
2-pair UTP/STP
Cat. 3, 4,5
100 m
100Base-TX
RJ-45
100/200 Mbps
2-pair UTP/STP
Cat. 5
100 m
100Base-FX
ST, SC
100/200 Mbps
MMF (50 or
2 km
100Base-FX
ST, SC
100/200 Mbps
SMF (9 or
20, 40, or 75
km
Cabling
Step 1: First, ensurethe power of the switch and end devicesare turned off.
<Note> Always ensure that the power is off before any installation.
Step 2:Prepare cable with corresponding connectors for each type of port in use.
Step 3: Consult Cable Specifications Table on previous page for cabling requirements
based on connectors and speed.
Step 4:Connect one end of the cable to the switch and the other end to adesired device.
Step 5: Once the connections between two end devices are made successfully, turn on the
power andthe switch is operational.

IES-0853 UserManual Page11
Web Management
The switch provides a browser interface that lets you configure and manage the switch
remotely.
After you set up your IP address for the switch, you
applications directly in your web browser by entering the IP address of the switch.You can
then use your web browser to list and manage switch configuration parameters from one
central location, justas if you were d
Web-Based Browser Management
The switch provides a web-based browser interface for configuring and managing the
switch.This interface allows you to access theswitch using a preferred web browser.
This chapter describes how to configure the switch using its web-based browser interface.
Default Setting
IP address: 192.168.1.10
User Name: admin
Password: [Blank]

IES-0853 UserManual Page12
Logging on to the switch
SWITCH IP ADDRESS
In your web browser, specify the IP address of the switch. Default IP address is
192.168.1.10.
USER NAME
Enter the factory default user name:admin.
PASSWORD
Enter the factory default password (no password).
Or enter a user-defined password if you followed the instructions later and changed the
factory default password.
OK

IES-0853 UserManual Page13
Browser Interface
The web browserinterface provides groups of point-and-click buttons at the left field of
the screen for configuring and managing the switch.
PoE
Port Based VLAN
Priority
Diff Serv Code Point
Bit 0 ~ 31, Bit 32 ~ 63
System Setup
Firmware Upgrade

IES-0853 UserManual Page14
PoE
PoE
1. System power budget: System power budget and type a new system
powerbudget.
2. OK: OK button to update yoursettings.
3. Enable mode: C Enable mode drop-down menu to choose Enable or Disable
Enable mode drop-down list to enable or disable Port 1 ~ Port 4 to discover
Powered Device (PD) connected to Port 1 ~ Port 4 of the Switch.
4. Power limit by classification: Check or uncheck Power limit by classification to enable
or disable Port 1 ~ Port 4 to provide power to PD according to classification of
maximum power range used by PD.
5. Fixed power limit(W): First uncheck Power limit by classification to disable Port 1 ~
Port 4 to provide power to PD according to classification of maximum power range
used by PD. Then c Fixed power limit(W) and type a new fixed power
limit for Port 1 ~ Port 4 to provide power to PD.
6. Power priority: C Power priority drop-down menu to choose Low, Middle, or
High Power priority drop-down list to determine power priority of Port 1
~ Port 4.
7. OK: OK button to update yoursettings.

IES-0853 UserManual Page15
High Power PoE Operation
This IndustrialWeb-Smart PoE & High Power PoE Ethernet switch is compliant with the
802.3af and 802.3at High Power standard,providing 30W of purepower to power
demanding devices such as pan-tilt-zoom (PTZ)network cameras, wireless access
bridge/routers and large-screen network video phones et cetera.
This 802.3af High Power switchs PoE operation with 802.3at based PD is highly versatile
and adaptable.Normally, when an 802.3at PD is connected to an 802.3af High Power
compliant switch, theswitch will detect that the PDs powerrequirement is based on class
4 classification outlined in the IEEE802.3at standard, and only attempt to provide 15.4W of
power, which is insufficient to power a 30W 802.3at PD.This is due to the reason that the
30W of powerin 802.3af High Power is classified as class 0. However, this 802.3af High
Power switch can support 30W 802.3at PD by setting the switch explicitly to provide a
fixed rate of 30W power to 30W 802.3at PD.
Power limit by classification: Uncheck Power limit by classification to disable Port 1 ~ Port
4 to provide powerto 30W 802.3at PD according to classification of maximum power
range used by PD.
Fixed power limit(W): C Fixed power limit(W) and type a new fixed power
limit 30W for Port 1 ~ Port 4 to provide power to 30W 802.3at PD.
OK: OK button to update yoursettings.

IES-0853 UserManual Page16
Port BasedVLAN
PortBasedVLAN
1. VLAN.1 ~VLAN.7:Click and choose Port 1 ~ Port 8 to be added intoVLAN.1 ~VLAN.7.
2. Cancel: Cancel button to cancel your settings.
3. OK: OK button to update yoursettings.

IES-0853 UserManual Page17
Priority
Priority
1. Ratio Scheme: Click and choose All High Before Low , 10:1, 5:1 , or 2:1 ratio scheme.
2. Port 1 ~ Port 8: Click and choose TOS, 802.1p, or Port Priority ( High or Low ) for
Port 1 ~ Port 8.
3. 802.1p Level 7 ~ Level 0: Click and set High or Low priority to queue of 802.1p Level
7 ~ Level 0.
4. Cancel: Cancel button to cancel your settings.
5. OK: OK button to update yoursettings.

IES-0853 UserManual Page18
Diff Serv Code Point
DiffServCodePoint
Bit 0 ~ 31:
1. Diff Serv Code Point:Check and set Bit 0 ~ 31 of Diff Serv Code Point to high priority.
2. Cancel: Cancel button to cancel your settings.
3. OK: OK button to update yoursettings.
Bit 32 ~ 63:
1. Diff Serv Code Point: Check and set Bit 32 ~ 63 of Diff Serv Code Point to high priority.
2. Cancel: Cancel button to cancel your settings.
3. OK: OK button to update yoursettings.

IES-0853 UserManual Page19
System Setup
SystemSetup
System Configuration:
1. DHCP Client: Click and choose Enable or Disable to enable or disable the Switch as
DHCP client to be automatically supplied an IP address, gateway address, and subnet
mask from DHCP server.
2. IP Address: C IP Address text box and type a new address to change the IP
Address.
3. Subnet Mask: C Subnet Mask text box and type a new address to change the
Subnet Mask.
4. Default Gateway: C Default Gateway text box and type a new address to change
the Default Gateway.
5. Cancel: Cancel button to cancel your settings.
6. OK: OK button to update yoursettings.
Password Configuration:
1. Old Password: Old Password and type in the old password.
2. NewPassword: NewPassword andtype in a new password.
3. Confirm Again: Confirm Again . Type the same password in New
Password again to verify it.
4. Cancel: Cancel button to cancel your settings.
5. OK: OK button to update yoursettings.
System Reset/Restore to default:
1. Load Default: Load Default button to restorethe default settings of the Switch.
2. Reset System: Reset System button to restart the Switch.

IES-0853 UserManual Page20
Firmware Upgrade
FirmwareUpdate
1. Cancel:C Cancel button to cancel firmware update request.
2. Update: C Update button and wait for firmware update request being processed.