LevelOne Infinity IES-0510 User manual

IES-0510
4 FE + 1 MM SC Unmanaged Switch -10 to 60, DIN-rail
User Manual
v1.00 - 1206

IES-0510 User Manual Page 2
Preface
A member of the growing family of rugged switches, this switch addresses a need for
a smaller switch. This switch provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial floor shop, multitenant
dwellings or Fiber To The Home (FTTH) applications. Capable of operating at
temperature extremes of -10°C to +60°C, this is the switch of choice for harsh
environments constrained by space.
Plug-and-Play Solution:
The switch is a plug-and-play Fast Ethernet Switch in compact size. It doesn't have
any complicated software to set up.
This manual describes how to install and use the Industrial compact Ethernet Switch.
This switch integrates full wire speed switching technology. This switch brings the
answer to complicated Industrial networking environments.
To get the most out of this manual, you should have an understanding of Ethernet
networking concepts.
In this manual, you will find:
Features on the switch
Illustrative LED functions
Installation instructions
Specifications

IES-0510 User Manual Page 3
Table of Contents
PREFACE...........................................................................................................................................................2
PRODUCT OVERVIEW.......................................................................................................................................4
INDUSTRIAL ETHERNET SWITCH.................................................................................................................................. 4
PACKAGE CONTENTS................................................................................................................................................ 4
PRODUCT HIGHLIGHTS ............................................................................................................................................. 5
FRONT PANEL DISPLAY ............................................................................................................................................. 6
PHYSICAL PORTS ..................................................................................................................................................... 6
INSTALLATION ..................................................................................................................................................7
SELECTING A SITE FOR THE SWITCH............................................................................................................................. 7
DIN RAIL MOUNTING.............................................................................................................................................. 7
CONNECTING TO POWER .......................................................................................................................................... 8
CONNECTING TO YOUR NETWORK .............................................................................................................................. 9
SPECIFICATIONS .............................................................................................................................................11
APPENDIX A –CONNECTOR PINOUTS ............................................................................................................12

IES-0510 User Manual Page 4
Product Overview
Industrial Ethernet Switch
Package Contents
When you unpack the product package, you shall find the items listed below. Please
inspect the contents, and report any apparent damage or missing items immediately
to your authorized reseller.
IES-0510
4 FE + 1 MM SC Unmanaged Switch -10 to 60, DIN-rail
Quick Installation Guide
CD User Manual

IES-0510 User Manual Page 5
Product Highlights
Basic Features
5-port 10/100Base-TX, 4-port 10/100Base-TX plus 1-port 100Base-FX, or 1-port
10/100Base-TX plus 1-port 100Base-FX.
Available in media converter format with 1-port 10/100Base-TX and 1-port
100Base-FX.
Support IEEE802.3/802.3u/802.3X.
Auto-negotiation: 10/100Mbps, Full/half-duplex; Auto MDI/MDIX.
Supports IEEE802.1p QoS with two priority queues.
Supports IEEE802.3az Energy Efficient Ethernet (EEE).
Support 2048 MAC addresses, 384K bits buffer memory.
Store-and-forward mechanism.
Full wire-speed forwarding rate and non-blocking mechanism.
Broadcast storm filtering.
Operating voltage and Max. current consumption: 0.2A @ 12VDC, 0.1A @
24VDC, 0.05A @ 48VDC.
Power consumption: 2.4W Max.
Power Supply: DC Terminal Block power input, 12-48VDC with polarity protection.
Plastic compact DIN-Rail Industrial case design.
DIN-Rail mounting ability.

IES-0510 User Manual Page 6
Front Panel Display
Power Status (PWR)
This LED comes on when the switch is properly connected to power and turned on.
Port Status LEDs
The LEDs display status for each respective port.
LED
State
Indication
10/100TX or 100FX
LNK/ACT
(Green)
Steady
A valid network connection established.
LNK stands for LINK.
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
100
(Yellow)
Steady
Light solid yellow for a port transferring at
100Mbps.
Off
The port is transferring at 10Mbps If this
LED is dark.
Physical Ports
This switch provides:
Five 10/100Base-TX ports
Four 10/100Base-TX ports + one 100Base-FX port
One 10/100Base-TX port + one 100Base-FX port
Connectivity
RJ-45 connectors
SC or ST connector on 100Base-FX fiber port

IES-0510 User Manual Page 7
Installation
This chapter gives step-by-step instructions about how to install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch where it will not be subjected
to extreme temperatures, humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
The ambient temperature should be between -10 to 60 degrees Celsius.
The relative humidity should be less than 95 percent, non-condensing.
Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.
Make sure that the switch receives adequate ventilation. Do not block the
ventilation holes on each side of the switch
The power outlet should be within 1.8 meters of the switch.
DIN Rail Mounting
Installation: Place the switch on the DIN rail from above using the slot. Push the front
of the switch toward the mounting surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch from the DIN rail.

IES-0510 User Manual Page 8
Connecting to Power
DC Terminal Block Power Inputs
Step 1: Connect the DC power cord to the plug-able terminal block on the switch, and
then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the switch.
The Terminal Block
PWR
Power Input
GND
Power Ground
Earth Ground

IES-0510 User Manual Page 9
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when connecting the switch to
your network. Use appropriate cables that meet your speed and cabling
requirements.
Cable Specifications
Speed
Connector
Port Speed
Half/Full
Duplex
Cable
Max.
Distance
10Base-T
RJ-45
10/20 Mbps
2-pair UTP/STP Cat.
3, 4, 5
100 m
100Base-TX
RJ-45
100/200 Mbps
2-pair UTP/STP Cat. 5
100 m
100Base-FX
SC, ST
100/200 Mbps
MMF (50 or 62.5μm)
2 km
100Base-FX
SC, ST
100/200 Mbps
SMF (9 or 10μm)
15, 40, or 75
km

IES-0510 User Manual Page 10
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port in use.
<Note> To connect two regular RJ-45 ports between switches or hubs, you need a
straight or cross-over cable.
Step 3: Consult the previous section for cabling requirements based on connectors
and speed.
Step 4: Connect one end of the cable to the switch and the other end to a desired
device.
Step 5: Once the connections between two end devices are made successfully, turn
on the power and the switch is operational.

IES-0510 User Manual Page 11
Specifications
Industrial Compact Switch
10/100Base-TX auto-negotiating ports with RJ-45 connectors,
100Base-FX fiber ports
Applicable Standards
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/FX
IEEE802.3az Energy Efficient Ethernet
IEEE802.1p Quality of Series (QoS)
Switching Method
Store-and-Forward
Forwarding Rate
10Base-T:
100Base-TX/FX:
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
Performance
148,80pps for 10Mbps
148,810pps for 100Mbps
Cable
10Base-T:
100Base-TX:
100Base-FX:
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)
LED Indicators
Per unit –Power status (PWR)
Per port –10/100TX or 100FX -
LNK/ACT (Green), 100 (Yellow)
Dimensions
26mm (W) × 70mm (D) × 110mm (H)
(1.02” (W) × 2.76” (D) × 4.33” (H))
Net Weight
0.2Kg (0.44lb.)
Power
Terminal Block: 12-48VDC
Operating Voltage &
Max. Current
Consumption
0.2A @ 12VDC, 0.1A @ 24VDC, 0.05A @ 48VDC
Power Consumption
2.4W Max.
Operating Temperature
-10℃to 60℃(14℉to 140℉)
Storage Temperature
-25℃to 85℃(-13℉to 185℉)
Humidity
5%-95% non-condensing
Safety
UL60950-1, EN60950-1, IEC60950-1
EMI
FCC Part 15, Class A
EN61000-6-3:
EN55022, EN61000-3-2, EN61000-3-3
EMS
EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
EN61000-4-11 (Voltage Dips Standards)
Environmental Test
Compliance
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)

IES-0510 User Manual Page 12
Appendix A –Connector Pinouts
RJ-45 Connector and Cable Pins
The following table lists the pinout of 10/100Base-TX ports.
Pin
Regular Ports
Uplink port
1
Output Transmit Data +
Input Receive Data +
2
Output Transmit Data -
Input Receive Data -
3
Input Receive Data +
Output Transmit Data +
4
NC
NC
5
NC
NC
6
Input Receive Data -
Output Transmit Data -
7
NC
NC
8
NC
NC