LevelOne WGR-6013 User manual

1
LevelOne
User Manual
Ver. 1.0
WGR-6013
300Mbps Wireless Gigabit Router

2
Safety
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
CE Declaration of conformity
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class B for ITE, the essential protection requirement of
Council Directive 89/336/EEC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
CE Marking Warning
Hereby, Digital Data Communications, declares that this product is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
The CE-Declaration of Conformity can be downloaded at:
http://www.levelone.eu/support.php

3
General Public License
This product incorporates open source code into the software and therefore
falls under the guidelines governed by the General Public License (GPL)
agreement.
Adhering to the GPL requirements, the open source code and open source
license for the source code are available for free download at
http://global.level1.com.
If you would like a copy of the GPL or other open source code in this software
on a physical CD medium, LevelOne (Digital Data Communications) offers to
mail this CD to you upon request, for a price of US$9.99 plus the cost of
shipping.

4
Table of Contents
Chapter 1 Introduction........................................................................... 5
1.1 Packing List................................................................................. 5
1.2 Spec Summary Table................................................................. 5
1.3 Hardware Configuration............................................................. 7
1.4 LED indicators............................................................................. 8
1.5 Button Definition.......................................................................... 9
1.6 Procedure for Hardware Installation........................................ 9
Chapter 2 Getting Start........................................................................ 11
Chapter 3 Making Configuration........................................................ 17
2.1 Login to Configure from Wizard.............................................. 18
2.2 System Status........................................................................... 23
2.3 Advanced................................................................................... 24
Appendix A FAQ and Troubleshooting............................................. 89
What can I do when I have some trouble at the first time?...... 89
How do I connect router by using wireless?............................... 91
IPAddress 192.168.1.1
Password admin
Wireless Mode Enable
Wireless SSID LevelOne
Wireless Security None

5
C
C
Ch
h
ha
a
ap
p
pt
t
te
e
er
r
r 1
1
1 I
I
In
n
nt
t
tr
r
ro
o
od
d
du
u
uc
c
ct
t
ti
i
io
o
on
n
n
Congratulations on your purchase of this outstanding Wireless Broadband Router. This
product is specifically designed for Small Office and Home Office needs. It provides a
complete SOHO solution for Internet surfing, and is easy to configure and operate even for
non-technical users. Instructions for installing and configuring this product can be found in this
manual. Before you install and use this product, please read this manual carefully for fully
exploiting the functions of this product.
1.1 Packing List
WGR-6013
Power Adapter
RJ-45 LAN Cable
Quick Installation Guide
CD Manual/QIG
Antenna
1.2 Spec Summary Table
Device Interface
Ethernet WAN 1 x RJ-45 port, 10/100/1000Mbps, auto-MDI/MDIX
Ethernet LAN 4 x RJ-45 port, 10/100/1000Mbps, auto-MDI/MDIX
Antenna 2 dBi detachable antenna
WPS Button For WPS connection
Reset Button Reset router setting to factory default
LED Indication Power/Status / WAN / LAN1 ~ LAN4/ WiFi
Power Jack DC Power Jack, powered via external DC 5V/1.2A
switching power adapter
Wireless LAN (WiFi)
Standard IEEE 802.11b/g/n compliance
SSID SSID broadcast or in stealth mode
Channel Auto-selection, manually
Security WEP, WPA, WPA-PSK, WPA2, WPA2-PSK
WPS WPS (Wi-Fi Protected Setup)
WMM WMM (Wi-Fi Multimedia)

6
Functionality
Ethernet WAN PPPoE, DHCP client, Static IP
WAN Connection Auto-reconnect, dial-on-demand, manually
One-to-Many NAT Virtual server, special application, DMZ, Super DMZ(IP
pass-through)
NAT Session Support NAT session(20000)
SPI Firewall IP/Service filter, URL blocking, Internet Access Control
DoS Protection DoS (Deny of Service) detection and protection
Routing Protocol Static route, dynamic route (RIP v1/v2)
Management SNMP, UPnP IGD, syslog, DDNS
Administration Web-based UI, remote login, backup/restore setting
Performance NAT up to 700Mbps and Wireless up to150Mbps
Environment & Certification
Package
Information Device dimension (mm) 185x119x32
Operation Temp. Temp.: 0~40°C, Humidity 10%~90% non-condensing
Storage Temp. Temp.: -10~70°C, Humidity: 0~95% non-condensing
EMI Certification CE/FCC compliance
RoHS RoHS compliance
*Specifications are subject to change without prior notice.

7
1.3 Hardware Configuration
Auto MDI/MDIX RJ-45 Ports
Automatically sense the types of WAN
and LAN when connecting to Ethernet
Power Jack
Antenna

8
1.4 LED indicators
LED status Description
Status Green in flash Device status is working.
WAN LED
Green RJ45 cable is plugged
Green in flash Data access
LAN LED Green RJ45 cable is plugged
Green in flash Data access
WiFi LED
Green WLAN is on
Green in flash Data access
Green in fast flash Device is in WPS PBC mode
Green in dark Wi-Fi Radio is disabled
LED Indicators
Power LED
LAN1~LAN4
LEDs
Wi-Fi
LED
WAN
LED
2 in1 Button
1.WPS
2.Wireless
ON
Status
LED
Reset
Button

9
1.5 Button Definition
Description
WPS When Wireless is On, press this button (about 1 sec) to execute
WPS function.
Wireless On When Wireless is off depend as Schedule Rule, Press this
button(about 5 sec) to enable "Wireless Radio".
Reset
1. Press this button then Power on the device
2. Press about 6 second, the device will reset to default then Status
LED flashes per sec in Normal status.
Notice: If Status LED flashes very fast, it means to press this button
too long and please try again.
1.6 Procedure for Hardware Installation
Step 1 Insert the Ethernet cable into LAN
Port:
Insert the Ethernet patch cable into LAN port
on the back panel of Router, and an available
Ethernet port on the network adapter in the
computer you will use to configure the unit.

10
Step 2 Insert the Ethernet patch cable into
Wired WAN port:
Insert the Ethernet patch cable form DSL
Modem into Wired WAN port on the back panel
of Router.
Step 3. Power on Router:
Connect the power adapter to the receptor on
the back panel of your Router.
Step 4. Complete the setup.
When complete, the Status LED will flash.

11
C
C
Ch
h
ha
a
ap
p
pt
t
te
e
er
r
r 2
2
2 G
G
Ge
e
et
t
tt
t
ti
i
in
n
ng
g
g S
S
St
t
ta
a
ar
r
rt
t
t
Insert the CD into CD reader on your PC. The program, AutoRun, will be executed automatically.
And then you can click the Easy setup Icon for this utility.
Configure the settings by the following steps.
2.1. Select Language then click “Next” for
continues.
2.2 Setup mode
You can select Wizard mode to run the
setup step-by-step or run advanced
mode to diagnose the network settings
of the router.

12
2.3 Advanced mode Setup.
Check the PC, Router or Internet icons
for the Status of PC, Router or Internet.
2.4 Quick Wizard Install mode Setup
1. Make sure the router is powered on.
2. Make sure your network adapter is
connected to the LAN port of the
router
3. Make sure your network adapter has
an IP address.
Click “Next” for continues

13
2.5. Wireless Setting.
Key in the SSID, Channel and Security
options, and then click “Next” for
continues.
2.6 Auto Detect WAN Service.
Click “Next” for continue.
Click the button, “Let me select WAN service
by myself”, to disable this function.
Note: The Item supports to detect the
Dynamic and PPPoE WAN Services only

14
Example, the Dynamic WAN type is
detected.
2.7. Manual select WAN Service
In the manual mode, Click the any icons for
continues.
2.8 Summary of the settings and Next
to “Reboot”
Click “Next” for continue.

15
2.9 Apply the Settings or Modify.
Click “Next” for continue.
2.10 Test the Internet connection.
Test WAN Networking service. Click “Next”
for continue.
You can ignore the by select the “Ignore
Test”.

16
2.11 Setup Completed.
The EzSetup is finish, you can open the
default web browser to configure advanced
settings of the Router.
Click “Finish” to complete the installation.

17
C
C
Ch
h
ha
a
ap
p
pt
t
te
e
er
r
r 3
3
3 M
M
Ma
a
ak
k
ki
i
in
n
ng
g
g C
C
Co
o
on
n
nf
f
fi
i
ig
g
gu
u
ur
r
ra
a
at
t
ti
i
io
o
on
n
n
This product provides Web based configuration scheme, that is, configuring by your Web
browser, such as Mozilla Firefox or or Internet Explorer. This approach can be adopted in any
MS Windows, Macintosh or UNIX based platforms.

18
2.1 Login to Configure from Wizard
Type in the IP Address
(http://192.168.1.1)
Type password, the default is
“admin” and click ‘login’ button.
Press “Wizard” for basic
settings with simple way.

19
Press “Next” to start wizard.
Step 1:
Set up your system password.
Step 2:
Select Wan Type.
Auto Detecting or
Setup Manually.

20
Step 3:
Setup the LAN IP and WAN
Type.
Step 4:
Please fill in PPPoE service
information which is provided by
your ISP.
Example: