Lexivon LX-771 User manual

LX-771 OPERATING INSTRUCTION

The LX-771 BUTANE MICRO TORCH
does not contain any butane gas when purchase.
USE HIGH-QUALITY REFINED BUTANE FUEL ONLY.
If the wrong butane is used, the torch can clog and sputter.
Make sure to use only butane that was refined at-least 3 times.
The more times the butane is refined, the better performance
you're going to get!
Please follow the gas filling instruction to make it operational.
A few attempts may be required to ignite in first use.
This unit is carefully designed to meet the
U.S.CPSC Child Resistant Standard requirement.
1. It is impossible to ignite flame before the SAFETY LEVER is released.
2. Before you set up the CONTINUOUS FLAME LOCK mode,
the flame will be extinguished immediately when
the IGNITION BUTTON is released.
ATTENTION
14X
REFINED
99%
PURE
BUTANE
9X
REFINED
BUTANE
3X
TRIPPLE
REFINED
BUTANE
PREMIUM
BUTANE
HIGH
QUALITY
BUTANE
BUTANE
FUEL
2

PRESENTATION
Sponge And Tray7mm & 8mm Wrench
Hot
Blower
Head
Catalyst
Hot
Knife
Standard
Tip
Diagonal
Tip - 3mm
Chisel
Tip - 3mm
Deflector
Flame Guard Ignition
Button
Tank
Continuous
Flame Lock
Safety
Lever
Flame Adjusting
Lever
3

1 GAS FILLING AND REFILLING
Figure 2
2 IGNITION
Figure 4Figure 3
Ignition
Enabled
Ignition
Disabled
Insert the butane container nozzle vertically down into the
FILLING VALVE. For best results, with pump-action several times.
(Please see Figure 2)
When the gas starts to overflow, remove the container nozzle from
FILLING VALVE immediately to stop the filling operation.
Wait at least 3 minutes to allow fuel gas to stabilize before igniting.
DO NOT OVERFILL THE GAS TANK.
Overfilling could cause igniting issues and erratic flame.
Before igniting, move the SAFETY LEVER (under the IGNITION BUTTON) to the left,
while simultaneously rotating the SAFETY LEVER in a clockwise direction until it clicks
into its place on the left side of the tool. (Please see Figure 3) Now, push the
IGNITION BUTTON for flame ignition. (Please see Figure 4) After ignition, the
SAFETY LEVER will automatically spring to the middle position.
NOTE: The flame will be extinguished and the SAFETY LEVER will spring back (to the
right) when releasing the IGNITION BUTTON before moving the CONTINUOUS
FLAME LOCK to the right to lock the flame. For temporary work, do not release the
IGNITION BUTTON until your work is finished.
Figure 1 Ensure the Continuous Flame Lock
is turned to ”OFF” position
before refilling.
(Please see Figure 1)
OFF
PUSH
Continuous
Flame Lock
Filling
Valve
Ignition
Button
4

Figure 5
3 CONTINUOUS FLAME WORKING
4 SHUT OFF
Figure 6
Figure 7
While the flame is on, move the
CONTINUOUS FLAME LOCK
(on the left of Torch, When the
muzzle points away from your
body) toward the direction of
IGNITION BUTTON to lock the
flame. (Please see Figure 5).
Move the FLAME ADJUSTING
LEVER (on the right of Torch) to
the left to decrease the flame
length, to the right to increase
the flame length.
(Please see Figure 6)
In the temporary working mode, release the IGNITION BUTTON to shut-off.
In continuous running mode, move the CONTINUOUS FLAME LOCK toward the
muzzle end to shut off the flame. (Please see Figure 7) Please make sure the unit is
completely cool before storing.
ON
Continuous
Flame Lock
Continuous
Flame Lock
OFF
RELEASE
5

5 HOW TO FIT OR REPLACE DIFFERENT ACCESSORIES
NOTE - ALWAYS ALLOW UNIT TO COOL BEFORE REMOVING OR REPLACING TIPS.
Use of the Soldering Tips, Hot Knife, Hot Blower, and Deflector requires the Head Catalyst
to be installed.
Unscrew the Flame Guard nut and remove the Flame Guard. Slide the Head Catalyst into
the Flame Guard by inserting the narrow end of the Head Catalyst into the Flame Guard
first. Place the Flame Guard with Head Catalyst back on to the tool and securely tighten
the Flame Guard nut.
Flame
Guard
Head
Catalyst
6

DEFLECTOR INSTALLATION:
Slide the Deflector over the Head Catalyst and make sure it attached firmly. To get more
control of the heat, install the Hot Blower tip on the Head Catalyst before you install the
Deflector.
• Never point at face or body when igniting.
• Do not touch the flame guard when hot.
• Danger - extremely flammable.
Contents under pressure.
• Contains flammable gas under pressure.
• Do not use near spark or open flame.
• Do not puncture or incinerate container or store at
temperatures above 120℉ or 50℃ or expose to
prolonged sunlight.
• Keep out of the reach of children.
• Do not try to disassemble the unit.
7mm Wrench 8mm Wrench
THREADED ATTACHMENT INSTALLATION:
Thread the desired tip into the Head Catalyst and tighten using the 7mm wrench while
using the 8mm wrench to hold the Head Catalyst in place. To remove, follow the
installation steps in reverse order.
Hot Blower Deflector
Head
Catalyst
7

THE LX-771 BUTANE MICRO TORCH MULTI-FUNCTION TOOL KIT
COMES WITH A 1 YEAR WARRANTY
FOR ANY HELP YOU MIGHT NEED
PLEASE DON’T HESITATE TO CONTACT US