Lexmark X782 User manual

Lexmark™ X782
Clearing Jams
Guide
Clearing jams
Understanding jam messages
Area A
1Release the levers on each side of the
multipurpose feeder to lay it flat.
2Press the pick assembly release lever, and
remove all media and jams.
3Return the feeder to its working position, and
reload your paper.
Area B
1Open the left access door until it clicks into
place.
2Remove all visible paper. Remove any torn
paper from the printer.
3Close the door.
4Open Tray 1, and make sure the entire paper
stack is pushed all the way down into the tray.
Area C
1Open the 500-sheet drawer access door. Hold
the door down while removing jams.
2Make sure the entire paper stack is loaded
correctly, and then close the door.
Area D
1Open the front access door.
2Hold down the front access door. Remove jams
in the rollers under the image transfer unit.
Area T1
1Open tray 1.
2Remove any jams.
3Make sure the paper is pushed all the way down
into the tray, and then close tray 1.
Message What to do
200 Paper Jam Clear Area B and Area T1.
201 Paper Jam Clear Area D, Area K, and Area L.
202 Paper Jam Clear Area K and Area L.
230 Paper Jam Clear Area E and Area J.
24<x> Paper
Jam
Clear Area B, Area C, and Area
T<x>.
250 Paper Jam Clear Area A and Area D.
27<x> Paper
Jam
Clear Area M.
29<x> Paper
Jam
Clear the scanner.

Area E
1Pull the duplex tray E completely out. Remove
any paper caught in the rollers or inside the
printer.
2Reinstall the duplex mechanism in the printer.
Area T<x>
1Carefully open trays 2 through 4 (all 500-sheet
trays), and then remove jams.
2Make sure the paper is pushed all the way down
into the tray, and then close trays 2 through 4.
Area J
1Remove the duplex tray J.
2Remove any jams, and then reinstall the tray.
Area K
1Open the lower right access door.
2Remove any jams, and then close the door.
Area L
1Open the upper right access door.
2Remove jams from the rollers, and then close
the door.
290, 291, 292, and 294 Scanner
Jams
1Remove all original documents from the ADF.
2Open the ADF cover, and carefully remove any
jammed pages.
If you cannot remove the jammed paper, and
open the document cover. Carefully remove the
jammed paper.
3Close the document and ADF covers.
Area M
1Open the rear door of the 5-bin mailbox or
output expander.
2Pull the jam straight out, and then close the
door.

Clearing fuser jams
1Clear the paper path. If the jam error message
persists, go to step 2.
2Open both the upper right and the lower right
access doors (Areas K and L).
CAUTION: The fuser assembly may be hot. Let
it cool before continuing.
3Pull down the latches. They slide toward the
center to release the fuser.
4Pull the fuser out, and set it on a clean, flat
surface.
5Unsnap the housing and set it aside.
6Lift up the fuser roller cover and remove the
jam.
7Close the fuser roller cover.
8Snap the housing back onto the fuser.
9Insert the fuser back into the printer.
10 Slide the latches out, and then pull up to
refasten them.
11 Close the doors.
Clearing image transfer unit jams
1Open the front access door and the left access
door.
2While holding down the front access door,
insert a folded piece of paper as shown to clear
the paper sensors under the image transfer
unit. Make sure to clear the entire width of the
paper path.
3Close the left access door and the front access
door. If the jam persists, continue with step Turn
the printer off. Open the front cover..

4Turn the printer off. Open the front cover.
5Remove all the print cartridges.
aPull up slightly on the cartridge handhold.
bPull the cartridge straight out and use the
handle to lift it off the guides.
cPlace the cartridges on a clean, flat surface
out of direct light.
6Release the latches to open the multipurpose
feeder (area A) all the way.
7Remove the image transfer unit.
aRaise the lever to unlock the image transfer
unit.
bPull down on the handle.
cSlide the image transfer unit out and place it
on a clean, flat surface.
Warning: Do not touch the transfer belt.
Touching the belt will damage the
image transfer unit.
8Look inside the printer. Remove all torn paper
or other jams.
9Insert the image transfer unit back into the
printer.
aAlign the guides with the insertion grooves
and gently slide the unit in.
bRotate the handle up, and push gently to
lock the unit in place.

cLower the lever to lock the image transfer
unit into place.
10 Return the multipurpose feeder to its working
position.
Reinstall all the print cartridges.
11 Close the printer door.
12 Turn the printer on. The printer returns to a
Ready state.
If you still need help
1Turn the printer off and then back on.
2Contact your administrator or Help desk if you
need more assistance.