Lezyne Mini GPS User manual

1

Information
For more information on Lezyne products, visit: http://lezyne.com
WEEE Notice & Product Disposal:
The symbol of the crossed waste container means that, in accordance with2002/96/EC
Waste Electrical and Electronic Equipment Directive (WEEE),once the product reaches
the end of its lifecycle, in the European Union it is subject to special waste disposal. In
addition to the present device, this rule is also applied to all items carrying such a symbol.
Do not dispose of these products as undifferentiated urban waste but put away for material
differentiated recycling.
CE RF Compliance—Meets the EU Requirements:
The equipment complies with the RF Exposure Requirement 1999/519/EC, Council
Recommendation of 12 July 1999 on the limitation of exposure of the general public to
electromagnetic fields (0–300 GHz). Changes or modifications to this product not authorized
by the manufacturer could void the EMC compliance and negate your authority to
operate the product. This product has demonstrated EMC compliance under conditions
that included the use of compliant peripheral devices and shielded cables between system
components. It is important that you use compliant peripheral devices and shielded
cables between system components to reduce the possibility of causing interference to
radios, televisions, and other electronic devices. We, hereby, declare that this cellular,
Wi-Fi radio is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC. Products with CE marking comply with the EMC Directive
(2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of
the European Community. Compliance with these directives implies conformity to the
following European Norms (in parentheses are the equivalent international standards).
FCC & IC User Warning Notice:
Any changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Labeling Requirement Notice:
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
FCC:
1. This Transmitter must not be co‐located or operating in conjunction with any
other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator
IC:
This device complies with the Canada portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such function is
available.
Lezyne is a trademark of Lezyne USA, Inc. and registered both in the United States and
internationally Any unauthorized use is expressly prohibited
2

Warranty
Lezyne GPS devices carry a one (1) year warranty from the original purchase date to the original owner (proof of purchase is required.) This warranty covers materials and manufacturing defects
on the GPS housing, electronics, and the mounting bracket supplied. Issues not covered by the warranty include normal wear and tear, consumable parts, such as batteries, unless product
damage has occurred due to defect in material or manufacturing, improper installation, attempting to access electronics, modifying electronics, damage or failure due to accident, misuse, abuse,
or neglect.
Because of possible user resealing error of the USB port, this product is not warrantied against water in the housing from improper sealing or any resulting damage. Please review and follow the
instructions carefully when sealing the housing.
This product is intended to be used only as a cycling aid and must not be used for any purpose requiring precise measurement of direction, distance, location or topography. Lezyne makes no
warranty as to the accuracy or completeness of map data in this product.
In no event shall Lezyne be liable for incidental or consequential damages for any traffic fines or citations, relating to or resulting from the use of this product or any of its parts. Lezyne assumes
no liability for any accident, injury, death, loss, or other claim related to or resulting from the use of this product.
3
Important
Do not be come distracted by the device—always operate vehicles in a safe manner.
Lezyne USA, Inc. does not accept any liability for injuries or other damages resulting from
the use of this product in any circumstances.
DO NOT SUBMERGE UNDER WATER
Lezyne GPS devices are water resistant under normal conditions, but are not waterproof. If moisture gets inside device body, air-out until completely dry.
DO NOT ATTEMPT TO REMOVE ELECTRONICS
Doing so will void warranty.
Do not operate or store outside of temperature range (-20–60° C). Battery lifemay be affected at temperature extremes.
Location and surroundings may affect GPS signal. For best results, use the device outdoors
with an unobstructed view of the sky. It may take up to 60 seconds to acquire GPS
signals.
This GPS device is not a calibrated measuring tool. It should not be used for surveying
purposes. GPS based elevation measurements may vary. Calorie readings are an estimation
for reference only.
CA PROPOSITION 65 WARNING:
This product may contain chemicals known to the State
of California to cause cancer and birth defects or other reproductive harm (California law
requires this warning to be given to customers in the State of California). For more info:
www.lezyne.com/prop65

Table of Contents
•Getting Started
–Buttons
–Screen Icons
–Charging GPS
–Installing GPS
–Turning on GPS
–GPS Satellite Signal
–Starting a Ride
–Ending a Ride
–Uploading a Ride to your Computer
•Screen Set up
–Layout
–Fields
–Unit Format
–Brightness (Backlight)
•Time Set up
–Time Format
–Time Zone*
–Daylight Saving*
•Personal Set up
–Sport Type
–Language*
–Age*
–Weight*
–Height*
–Gender*
•Auto/Preset Notification Set up
–Scroll
–Pause
–Lap
–Light (Backlight)
•Alert Set up
–Ride Distance
–Ride Time
–Calories
•Records
–Erase All
–Erase Oldest
–Memory
–Reset Trip 1
–Reset Trip 2
–Reset Odo (Odometer)
•Info
–Device
–Firmware
–GPS
–Sats
•Specifications
•Data Metrics Explained
•Troubleshooting
–Updating Software
–Support
–Resetting the Device
4

ENTER Hold for 2 seconds to turn ON/OFF the device
Press to ENTER a selection in the menu screen
During a ride, Press to turn Backlight ON/OFF
MENU Hold to access the MENU screen
Press to move UP in the menu screen
During a ride, Press to Scroll bottom data line
LAP Press to start a ride
Hold to end a ride
Press to move DOWN in the menu screen
During a ride, Press to mark a LAP
Getting Started
Buttons
5
Press
Hold
On/Off
Backlight
Menu
Scroll
Pause
Start/Lap
Ride Screen Button Functions

Getting Started
6
Press
Hold
Select
Up
Down
Menu and Pause Screen Button Functions
Screen Icons
GPS Status Battery Status

Before using your Lezyne GPS device for the first time, fully charge battery
and it is also recommended to visit lezyne.com/gpsroot/gps_downloads.php and update your GPS
device to the latest software.
1. Remove exterior moisture
2. Open USB cover
3. Connect micro USB cable and device to powered USB port.
For best results, use the supplied Lezyne cable
If device does not display charging symbol when plugged in, selected USB
port may not be powered –try another USB port.
Open USB cover for charging
Mounting tabs
Getting Started
Charging
To attach the X-Lock mount:
1. Align the shim with the bottom of the mount
2. Attach the X-Lock mount securely using the two bands
the best fit your mounting location
To connect the device to the X-Lock mount:
1. Align the tabs on the back of the device with the mount
2. Press down and turn the device until it locks into place
Mounting
7

Turning on the GPS
Press and hold for 2
seconds to turn on
GPS Satellite Signal
Before a ride can start there must be a GPS signal present. This can take 30 to 90
seconds. For best results:
1. Go outside to an open and clear area
2. Place the GPS device so its not obstructed from the sky
3. Wait for a GPS status dotsto fill in
*a pop up notice will appear if you try to start a ride before a GPS signal is present.
GPS Signal
Getting Started
Turn on your Mini GPS by holding the left button.
8

Enter the pause menu by holding the bottom right button . To continue
recording, select the option RESUME by pressing the left button ENTER or scroll
through other options by pressing one of the top or bottom right buttons
Select the option END to go to the file menu. Now choose to SAVE or DISCARD
your file
Starting a Ride
Press to start
recording a ride
1. At least 1 GPS status dots will fill solid
when ready.
2. Start recording by pressing the bottom
right button.
3. Ride data is recorded when the timer is
running
4. Press to see other ride metrics
Press and hold to
end ride
Ending a Ride
Getting Started
9

Uploading a Ride to a computer
1. Remove the USB port seal
2. Connect your Mini GPS to a computer via Micro USB cable.
3. The GPS will read like a USB drive with included folders
4. Within the Lezyne GPS folder find your .Fit ride files in the Activities folder to
upload and share at www.lezyne.com/gpsroot
Getting Started
USB Seal
Its important to re-install the USB seal between the two seal locks to maintain a
good seal against the weather
GPS Device updates
Software updates for your GPS device can be found at
http://www.lezyne.com/gpsroot/gps_downloads.php
10

Layout Display
There are three display options.
•2 Lines of Data
•3 Lines of Data
•4 Lines of Data
The layouts can change but the display fields are set.
To change the Layout,
1. press the left ENTER button,
2. use the right buttons to scroll up and down until it list the desired lines of
data to display,
3. press ENTER to select
Screen Set up
2 Lines of Data 3 Lines of Data 4 Lines of Data 11
Speed
Scroll Data
Speed
Timer
Scroll Data
Speed
Timer
Distance
Scroll Data
Menu Screen
Hold to enter the MENU screen

Fields Display
In Fields you can choose what data metrics to display on the bottom data line
Press ENTER to make it Hidden or Visible. Standard data is always visible.
Screen Set up
Units Display
In Units you can choose between Miles or Kilometer format.
Press ENTER and toggle up or down, press ENTER to select the setting
12
Adjustable Data
Trip 1
Trip 2
Ascent
Descent
Avg Speed
Max Speed
Calories
Odometer

Brightness Display
In Brightness you can choose what percentage of light is displayed from the
backlight. Press ENTER and use the right buttons to select INCREASE or
DECREASE. Use the ENTER button to make the adjustments. When done select
BACK.
Screen Set up
Time Set up
Time Format
Time Format adjusts time display from 12hr to 24hr format. Press ENTER and
use the right buttons to select 12hr or 24hr. Press ENTER to make the selection.
13

Time Zone
Time Set up
Daylight Savings
Time Zone adjusts time based on your closest location. Press ENTER and use the
right buttons to select. Press ENTER to make the selection.
Daylight Savings adjusts time accordingly if it applies to your location. Press
ENTER and use the right buttons to select. Press ENTER to make the selection.
14

Sport Type
Personal Set up
Language Setting
Sport Type gives you the option of ROAD or MOUTAIN to choose what best suits
your type riding and how it should be categorized for downloads.
Press ENTER and use the right buttons to select. Press ENTER to make the
selection.
Sets your desired language.
Press ENTER and use the right buttons to select. Press ENTER to make the
selection
15

Weight Setting
Personal Set up
Age Setting
Setting your age assists in calorie calculations.
Press ENTER and use the right buttons to select INCREASE or DECREASE. Use the
ENTER button to make the adjustments. When done select BACK.
Setting your weight assists in calorie calculations.
Press ENTER and use the right buttons to select INCREASE or DECREASE. Use the
ENTER button to make the adjustments. When done select BACK.
16

Gender Setting
Personal Set up
Height Setting
Setting your Height assists in calorie calculations.
Press ENTER and use the right buttons to select INCREASE or DECREASE. Use the
ENTER button to make the adjustments. When done select BACK.
Setting your gender assists in calorie calculations. Set you gender to Male or Female.
Press ENTER and use the right buttons to select. Press ENTER to make the selection
17

Start/Stop (Pause) Setting
Auto/Preset Notification Set up
Scroll Setting
Automatic Scroll set for the bottom data line.
Press ENTER and use the right buttons to select On or Off. Press ENTER to make
the selection
The Pause setting is an automatic Start/Stop feature that controls recording of the ride if
you stop for a period of time. And will start back up once you begin to move.
Press ENTER and use the right buttons to select On or Off. Press ENTER to make the
selection
18

Light Setting
Auto/Preset Notification Set up
Lap Preset Notification Set up
Lap preset allows you set a notification pop up based on Time or Distance goals.
Press ENTER and use the right buttons to select Time or Distance. Press ENTER
to make the selection. Press ENTER and use the right buttons to select INCREASE
or DECREASE. Use the ENTER button to make the adjustments. When done
select BACK. To reset, select Off and repeat the steps for set up.
The Light setting automatically turns the backlight on when ever a button is pressed.
Press ENTER and use the right buttons to select On or Off. Press ENTER to make the
selection
19

Ride Time Alert Set up
Alert Set up
Ride Distance Alert Set up
Ride Distance alert gives you a pop up alert when you complete a set distance
goal. Press ENTER and use the right buttons to select INCREASE or DECREASE.
Use the ENTER button to make the adjustments. When done select BACK. To
reset, select Off and repeat the steps for set up.
Ride Time alert gives you a pop up alert when you complete a set a goal for an
amount of time. Press ENTER and use the right buttons to select INCREASE or
DECREASE. Use the ENTER button to make the adjustments. When done select
BACK. To reset, select Off and repeat the steps for set up.
20