LG 47TS30MF User manual

www.lg.com
OWNER’S MANUAL
MONITOR SIGNAGE
26TS30MF
47TS30MF
Please read this manual carefully before operating the your set and
retain it for future reference.
MONITOR SIGNAGE MODELS
ENG
ENGLISH

2
ENG
ENGLISH
CONTENTS
CONTENTS
3 INSTALLATIONPREPARATION
3 Accessories
4 MountingHoles
6 UnpackingandCabling
8 PortraitLayout(Onlysupportedfor47TS30MF)
9 StorageMethodforPanelProtection
9 - CorrectMethod
9 - IncorrectMethod
10 PRODUCTINSTALLATION
10 Lightinginstallation
11 InstallationinEnclosure
12 Precaution
12 - CorrectMethod
12 - IncorrectMethod
13 TROUBLESHOOTING
14 SPECIFICATIONS
14 26TS30MF
15 47TS30MF
16 LVDSPINMAPGUIDE
16 26TS30MF
17 47TS30MF

3
ENG
ENGLISH
INSTALLATIONPREPARATION
INSTALLATIONPREPARATION
Accessories
Checkyourproductboxforthefollowingitems.Ifthereareanymissingaccessories,contactthelocal
dealerwhereyoupurchasedyourproduct.Theillustrationsinthismanualmaydifferfromtheactualproduct
andaccessories.
 Donotuseanyunapprovedorcounterfeitpartsoraccessoriestoensurethesafetyandproductlife
span.
 Anydamagesorinjuriesbyusingunapproveditemsarenotcoveredbythewarranty.
 Theaccessoriessuppliedwithyourproductmayvarydependingonthemodel.
 Productspecificationsorcontentsinthismanualmaybechangedwithoutpriornoticeduetoupgrade
ofproductfunctions.
CD(Owner'sManual)/
Card/EasySetupGuide
CAUTION
NOTE

4
ENG
ENGLISH
INSTALLATIONPREPARATION
MountingHoles
UseM3x4mmscrewstomountthemonitor.Thereare16screwholesontherearsideoftheproduct.
26TS30MF
<Frontsideoftheproduct>
<Rearsideoftheproduct>

5
ENG
ENGLISH
INSTALLATIONPREPARATION
UseM3x4mmscrewstomountthemonitor.Thereare20screwholesontherearsideoftheproduct.
47TS30MF
<Frontsideoftheproduct>
<Rearsideoftheproduct>
 Thisproducthasthefrontandbacksides.Makesuretheproductisinstalledwiththefrontsidefacing
forward.
 Imageisdisplayedreverselyonthebackside.
CAUTION

6
ENG
ENGLISH
INSTALLATIONPREPARATION
UnpackingandCabling
1 Liftupthecoverofthebox. 2 Removethetoppackaging.
3 Holdbothsidesoftheproductandliftitup.
5 Placeasoftclothonthetableandputthe
productdownwiththescreenfacingdownward.
4 Removethepolybag.
6 ConnecttheLVDScable(Additionalassembly
isrequired).AscalerboardorLVDScableis
optionalandnotprovidedwiththeproduct.
26TS30MF

7
ENG
ENGLISH
INSTALLATIONPREPARATION
1 Liftupthecoverofthebox. 2 Removethetoppackaging.
3 Holdbothsidesoftheproductandliftitup.
5 Placeasoftclothonthetableandputthe
productdownwiththescreenfacingdownward.
4 Removethepolybag.
6 ConnecttheLVDScable(Additionalassembly
isrequired).AscalerboardorLVDScableis
optionalandnotprovidedwiththeproduct.
47TS30MF
 Pleasereferto"LVDSPinMapGuide"onpages16to18fortheLVDScableassembly.
NOTE

8
ENG
ENGLISH
INSTALLATIONPREPARATION
PortraitLayout(Onlysupportedfor47TS30MF)
Toinstallinportraitmode,rotatethesetclockwise90degreeswhenlookingatfromthefront.
Theportraitmodeisonlyavailableonthescalerboard.(Thescalerboardshouldsupportportraitmode.)
 The26TS30MFmodelcannotberotated.
 Thescalerboardisoptionalanditisnotpartoftheproduct.
CAUTION

9
ENG
ENGLISH
INSTALLATIONPREPARATION
CorrectMethod IncorrectMethod
StorageMethodforPanelProtection
Panel
Cushion
Whenlayingdowntheproduct,placeacushionor
asoftclothonaflatfloor.Puttheproductdown
withthepaneloftheproductfacingdown.
Ifthereisnoacushionorasoftclothavailable,
ensurethefloorisclean.Thenlaytheproduct
downcarefullywiththepanelfacingeitherupward
ordownward.Atthistime,makesurethatno
objectfallsonthepanel.
Panel
Panel
Panel
Iftheproductistiltedontothebezel,thebottomof
thepanelmaybedamaged.
Iftheproductistiltedontotheedgeofthepanel,
thepanelmaybedamaged.

10
ENG
ENGLISH
PRODUCTINSTALLATION
PRODUCTINSTALLATION
Lightinginstallation
Thisproductmustbeinstalledwithlighting.
Lightingmustbeinstalledbehindtheproductsothatthedisplaycanbeseenclearly.
Installingacertainobjectbehindthescreenmayrequireadditionallighting.
Lighting 600luxormore
Lighting 600luxormore
Additionallighting
Additionallighting
Object

11
ENG
ENGLISH
PRODUCTINSTALLATION
 Thisproductcanbeinstalledinvarious
locationsbesidestheenclosure.
<Exampleoftheproductintheenclosure>
<Exampleofthelightinginstallation>
Lightingmustbeinstalledintheenclosure.
InstallationinEnclosure
Installtheproductintheenclosure.
1 Placetheproductintheenclosure.
2 Attachtheproductusingthepreparedscrew
holesandanadditionalenclosureguideframe.
NOTE
 Thepanelofthisproductissothinthatit
canbeeasilybrokenwhenitisexposedto
theoutside.Pleaseusetheprotectiveglass
topreventtheproductfromdirectlybeing
exposedtotheoutside.
CAUTION

12
ENG
ENGLISH
INSTALLATIONPREPARATION
Precaution
Donotliftuptheproductbyholdingacorner.Donotholdthescreenareawhenholdingthe
product.
Useasoftclothmoistenedwithn-hexaneto
removedustorstainsonthescreen.
CorrectMethod IncorrectMethod
 Makesurethepowerisdisconnectedbefore
movingorinstallingtheproduct.Otherwise
electricshockmayoccur.
 Ifyouinstalltheproductonaceilingor
slantedwall,itmayfallandresultinsevere
injury.
 Donotfastenthescrewstootightly;thismay
causedamagetotheproductandvoidyour
warranty.
 UseM3x4mmscrewstomountthe
monitor.Anydamagesorinjuriescausedby
misuseoruseofimproperaccessoriesare
notcoveredbythewarranty.
CAUTION

13
ENG
ENGLISH
TROUBLESHOOTING
TROUBLESHOOTING
After-imageappearsontheproduct.
Problem Resolution
After-imageappearswhenthe
productisturnedoff.

Ifyouuseafixedimageforalongtime,thepixelsmaybedamaged
quickly.Usethescreen-saverfunction.
Screencolorisabnormal.
Problem Resolution
Screencolorisunstableor
mono-colored.

ChecktheconnectionstatusoftheLVDScable.

CheckwhethertheLVDScableisconnectedcorrectlyfollowingthe
"LVDSPinMapGuide".
Doblackspotsappearonthe
screen?

Severalpixels(red,green,whiteorblackcolor)mayappearonthe
screen,whichcanbeattributabletotheuniquecharacteristicsofthe
LCDpanel.ItisnotamalfunctionoftheLCD.

14
ENG
ENGLISH
SPECIFICATIONS
SPECIFICATIONS
26TS30MF
CN1
(30pin)
EEPROM
S1
SCL SDA
S1366
Source Driver Circuit
LVDS Select #9
LVDS 1Port
+12.0V
Timing Controller
[LVDS Rx]
TFT - LCD Panel
(1366 x RGB x 768 pixels)
[Gate In Panel]
G1
G768
RGB
Control
Signals
Power Signals
Power Circuit
Block
ScreenSize 26.01inche(660.6mm)diagonal
Dimension(WxHxD) 609mmx412.8mmx8.8mm
PixelPitch 140.5㎛xRGBX421.5㎛
PixelFormat 1366horiz.by768vert.pixelsRGBstripearrangement
ColorDepth 8bit(D),16,7Mcolors
Transmittance(WithPOL) 4.84%(Typ.)
ViewingAngle(CR>10) Viewinganglefree(R/L178(Min.),U/D178(Min.))
PowerConsumption Total2.7W(Typ)(TBD)
Weight(head) 1.62kg
DisplayOperatingMode Transmissivemode,Normallyblack
SurfaceTreatment(Top) Hardcoating(3H),Anti-glaretreatmentofthefrontpolarizer(Haze10%)
PossibleDisplayType Landscapeonly


15
ENG
ENGLISH
SPECIFICATIONS
47TS30MF
CN1
(51pin)
EEPROM
S1
SCL SDA
S1920
Source Driver Circuit
Timing Controller
LVDS Rx + DCA + ODC
Intergrated TFT - LCD Panel
(1920 x RGB x 1080 pixels)
[Gate In Panel]
G1
G1080
Mini-LVDS
(RGB)
Control
Signals
Power Signals
LVDS 2Port LVDS 1,2
I2C
Option
signal
LVDS Select
Bit Select
+12.0V
Power Circuit
Block
ScreenSize 46.96inch(1192.87mm)diagonal
Dimension(WxHxD) 1165.9mmx663.27x8.8mm
PixelPitch 0.5415mmx0.5415mm
PixelFormat 1920horiz.by1080vert.Pixels,RGBstripearrangement
ColorDepth 10Bit(D),1.07Billioncolors
Transmittance(WithPOL) 5,5%(Typ.)
ViewingAngle(CR>10) Viewinganglefree(R/L178(Min.),U/D178(Min.))
PowerConsumption Total6.6W(Typ.)(TBD)
Weight(head) 4.56kg
DisplayOperatingMode Transmissivemode,Normallyblack
SurfaceTreatment(Top) Hardcoating(3H),Anti-glaretreatment(Reflectance<2%),
PossibleDisplayType LandscapeandPortraitEnabled


16
ENG
ENGLISH
LVDSPINMAPGUIDE
LVDSPINMAPGUIDE
26TS30MF
PinNo. Symbol Description Note
1 VLCD PowerSupply+12.0V
2 VLCD PowerSupply+12.0V
3 VLCD PowerSupply+12.0V
4 VLCD PowerSupply+12.0V
5 GND Ground
6 GND Ground
7 GND Ground
8 GND Ground
9 LVDSSelect 'H'=JEIDA,'L'orNC=VESA
10 NC NoConnection 4
11 GND Ground
12 RA- LVDSReceiverSignal(-)
13 RA+ LVDSReceiverSignal(+)
14 GND Ground
15 RB- LVDSReceiverSignal(-)
16 RB+ LVDSReceiverSignal(+)
17 GND Ground
18 RC- LVDSReceiverSignal(-)
19 RC+ LVDSReceiverSignal(+)
20 GND Ground
21 RCLK- LVDSReceiverClockSignal(-)
22 RCLK+ LVDSReceiverClockSignal(+)
23 GND Ground
24 RD- LVDSReceiverSignal(-)
25 RD+ LVDSReceiverSignal(+)
26 GND Ground
27 NC NoConnection(Note4) 4
28 NC NoConnection(Note4) 4
29 NC NoConnection(Note4) 4
30 GND Ground
 LVDSConnector(CN1):KDF71G-30S-1H(Hirose)orCompatible,Refertobelowtable.
 MatingConnector:FI-X30C2L(ManufacturedbyJAE)orEquivalent
 Cablelength:1mofFFCcableorless
Note:1.AllGND(Ground)pinsshouldbeconnectedtogethertotheLCDmodule'smetalframe.
2.AllVLCD(powerinput)pinsshouldbeconnectedtogether.
3.AllInputlevelsofLVDSsignalsarebasedontheEIA644Standard.
4.ThesepinsareusedonlyforLGD(Donotconnect).

17
ENG
ENGLISH
LVDSPINMAPGUIDE
47TS30MF
PinNo. Symbol Description Note
1 GND Ground 1
2NC NoConnection 4
3NC NoConnection 4
4NC NoConnection(ReservedforLGD) 4
5NC NoConnection(ReservedforLGD) 4
6NC NoConnection(ReservedforLGD) 4
7 LVDSSelect 'H'=JEIDA,'L'orNC=VESA
8NC NoConnection
9NC NoConnection
10 NC NoConnection
11 GND Ground 1
12 RO0N FIRSTLVDSReceiverSignal(A-)
13 RO0P FIRSTLVDSReceiverSignal(A+)
14 RO1N FIRSTLVDSReceiverSignal(B-)
15 RO1P FIRSTLVDSReceiverSignal(B+)
16 RO2N FIRSTLVDSReceiverSignal(C-)
17 RO2P FIRSTLVDSReceiverSignal(C+)
18 GND Ground 1
19 ROCLKN FIRSTLVDSReceiverClockSignal(A-)
20 ROCLKP FIRSTLVDSReceiverClockSignal(A+)
21 GND Ground 1
22 RO3N FIRSTLVDSReceiverSignal(D-)
23 RO3P FIRSTLVDSReceiverSignal(D+)
24 RO4N FIRSTLVDSReceiverSignal(E-) 5
25 RO4P FIRSTLVDSReceiverSignal(E+) 5
26 NC NoConnection
27 BitSelect 'H'orNC=10bit(D),'L'=8bit
28 RE0N SECONDLVDSReceiverSignal(A-)
29 RE0P SECONDLVDSReceiverSignal(A+)
30 RE1N SECONDLVDSReceiverSignal(B-)
31 RE1P SECONDLVDSReceiverSignal(B+)
32 RE2N SECONDLVDSReceiverSignal(C-)
33 RE2P SECONDLVDSReceiverSignal(C+)
34 GND Ground 1
35 RECLKN SECONDLVDSReceiverClockSignal(-)
36 RECLKP SECONDLVDSReceiverClockSignal(+)
37 GND Ground 1
38 RE3N SECONDLVDSReceiverSignal(D-)
39 RE3P SECONDLVDSReceiverSignal(D+)
40 RE4N SECONDLVDSReceiverSignal(E-) 5
41 RE4P SECONDLVDSReceiverSignal(E+) 5
 LVDSConnector(CN1):FI-RE51S-HForEquivalent,Refertobelowtable.
 MatingConnector:FI-RE51SorEquivalent
 Cablelength:1mofcoaxialcableorless

18
ENG
ENGLISH
LVDSPINMAPGUIDE
Note:1.AllGND(Ground)pinsshouldbeconnectedtogethertotheLCDmodule'smetalframe.
2.AllVLCD(powerinput)pinsshouldbeconnectedtogether.
3.AllInputlevelsofLVDSsignalsarebasedontheEIA644Standard.
4.Specificpins(pinNo.#2~#6)areusedforinternaldataprocessoftheLCDmodule.
Thesepinsshouldbenoconnections.
5.LVDSpin(pinNo.#24,25,40,41)areusedfor10Bit(D)oftheLCDmodule.
Ifusedfor8Bit(R),thesepinsarenoconnection.
PinNo. Symbol Description Note
42 NC NoConnection
43 NC NoConnection
44 NC NoConnection
45 GND Ground
46 GND Ground
47 GND Ground
48 VLCD PowerSupply+12.0V 2
49 VLCD PowerSupply+12.0V 2
50 VLCD PowerSupply+12.0V 2
51 VLCD PowerSupply+12.0V 2

Make sure to read the Safety Precautions
before using the product.
Keep the Owner's Manual(CD) in an accessible
place for future reference.
The model and serial number of the SET is
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
Temporarynoise isnormalwhenpoweringONor
OFFthisdevice.