LG S3RERB User manual

Read this owner’s manual thoroughly before operating
the appliance and keep it handy for reference at all
times.
S3RERB

2
MFL66101220 www.lg.com TABLE OF CONTENTS
TABLE OF CONTENTS
3 PRODUCT FEATURES
4
IMPORTANT SAFETY INSTRUCTIONS
4
Safety Instructions for Installation
5
Safety Instructions for Connecting Electricity
6
Basic Safety Precautions
7
Grounding Instructions
8
PRODUCT OVERVIEW
8
Parts
9
Accessories
10
The Moving Hanger
10
The Pants Crease Care
11
The Shelf
11 Choosing Styler Features
12 INSTALLATION
12 Installation Overview
12 Product Specifications
13 Unpacking the Styler
13 Choosing the Proper Location
14 Installation Location Requirements
14 Clearances
16 Leveling the Styler
17 Reversing the Door
17 Installing on Carpeting
18 Installing the Anti-Tip Device
18 Assembling the Drip Tray
18 Installing Cap Covers
18 Installing Hinge
Covers
19 OPERATION
19 Before Use
20 Using the Styler
21 Sorting Loads
Fabric Care Labels
Grouping Similar Items
Choosing Styler-Safe Clothing
22 Fabric Care Guide
24 Checking the Filters Before
Every Load
Checking the Lint Filter
Changing the Aroma Sheet
25 Checking the Water Tanks
25 Loading the Styler
Hangers
Using the Moving Hanger
Pants Hanger or Pants Crease Care
Shelf
29 Control Panel
Control Panel Features
31 Cycle Guide
Cycle Processes
32 Choosing a Cycle
33 Cycle Settings and Options
34 Special Functions
Locking the Controls
Turning Alert Sounds On/Off
Setting a Delayed Start Time
35 SMART FEATURES
35 Tag On
Before Using Tag On
Using the
Tag On Function
Using Tag On with Apps
Downloading Styler
Cycles

3
37 MAINTENANCE
37 Regular Cleaning
Cleaning the Interior and Exterior
Cleaning the Lint Filter
Cleaning
the Aroma Filter
Cleaning the Water Tanks
39 TROUBLESHOOTING
39 FAQs
40 Before Calling for Service 42
Error Codes
43 SMART DIAGNOSISTM
PRODUCT FEATURES
PRODUCT FEATURES
REFRESH CLOTHING OR ADD AN AROMA
Infuse items with the aroma from your favorite dryer fabric softener sheets to keep clothes and
accessories looking, feeling, and smelling refreshed.
REMOVE WRINKLES
The Refresh cycle also uses steam and a moving hanger that vibrates approximately 180 times per
minute to remove the wrinkles in clothing. Performance may vary depending on fabric type.
SHARPEN CREASES IN PANTS
Hang dress trousers flat in the Styler's Pants Crease Care feature. It will crease the pants legs and
reduce wrinkles elsewhere.

4
GENTLY AND EFFECTIVELY DRY
The heat pump drying technology of the Gentle Dry cycle provides low-heat drying which draws
moisture from clothes without the shrinking or damage associated with hot-air drying. Gently and
safely dry alpaca, camelhair and other non-washable fabrics that have become damp from rain or
snow, and wool sweaters, hand-washable knits, and other dryflat items after washing.
SANITIZE AND REDUCE ALLERGENS
The Styler's Sanitary cycle uses TrueSteam™ to destroy bacteria and other microorganisms
*Control Lock without damaging clothes. It maintains the optimal temperature necessary to sanitize each garment,
destroying bacteria that persist even when clothes are dried in sunlight.
SMART DIAGNOSIS™
Should you experience any technical difficulty with the Styler, it has the capability of transmitting
data by phone to the Customer Information Center. The call center agent records the data
transmitted from your machine and uses it to analyze the issue, providing a fast and effective
diagnosis. (Refer to page 43.)
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
There are many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result
in product damage, property damage, or serious bodily harm or death. The safety alert
symbol will be followed by either the hazard signal word WARNING or CAUTION. These
words mean:
WARNING Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, may result in minor or moderate
injury, or product damage.

5
WARNING
To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death when
using this appliance, follow basic safety precautions, including the following:
SAFETY INSTRUCTIONS FOR INSTALLATION
•Contact an authorized service center before
installing or relocating the S tyler to avoid injury
or product damage when moving the product.
•When moving the S tyler away from the wall, be
careful not to roll over or damage the power cord.
•The appliance is heavy. Two or more people are
necessary to move and install the appliance to
prevent damage or injury.
•Prior to use, ensure that you are connecting this
product to a dedicated grounded electrical outlet
rated for use with this product. It is the user’s
responsibility to replace a standard 2-prong wall
outlet with a standard 3-prong wall outlet.
•Before use, the appliance must be properly
installed as described in this manual.
Electric shock can result if the appliance is not
properly grounded.
•Do not install the S tyler where there may be a
danger of the unit falling. The product is not
designed for use on ships or airplanes. Check with
an authorized LG service center for use under
other special circumstances.
•Do not tamper with controls.
•Install the product where the floor is firm and
level. The product may vibrate excessively and
eventually fall if installed on an unstable surface,
causing damage or injury.
•Keep the front side protected when transporting
the appliance. Do not truck from the front. The
tempered glass panel on the front of the appliance
may break, causing damage or injury.
•Properly ground the appliance to conform with all
governing codes and ordinances.
Follow the details in the installation instructions.
Electric shock can result if the appliance is not
properly grounded.
•Install and store the appliance where it will not be
exposed to temperatures below freezing or
exposed to the weather. Allow the product to
warm to room temperature before use if it was
delivered in winter or at sub-sero temperature.
•Do not repair or replace any part of the appliance
or attempt any servicing unless specifically
recommended in the usermaintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out. Failure to follow this warning
can cause serious injury, fire, electric shock, or
death.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire, explosion,
or electric shock, or to prevent property damage, injury to persons, or death.

6
SAFETY INSTRUCTIONS FOR INSTALLATION
•
•
•
To reduce the risk of electric shock, do not
install the appliance in humid spaces such
as a bathroom. Failure to follow this
warning can cause death, serious injury,
fire, electric shock, or product deformation
or malfunction. Remove all packing items
and dispose of all shipping materials
properly. Failure to do so can result in
burns, fire, explosion, or death. Connect to
a properly rated, protected, and sized
power circuit to avoid electrical overload.
Improper power circuits can melt, creating
electric shock and/or fire hazard.
•
•
•
•
Keep all packaging from children. Packaging
material can be dangerous for children.
There is a risk of suffocation.
Do not install near another heat source
such as a stove, oven or heater. Failure
to follow this warning can cause
product deformation, smoke, or fire.
Do not place candles, smoking materials, or
other flammables on top of the product.
Dripping wax, smoke, or fire can result.
Remove all protective vinyl film from the
product. Failure to do so can cause
product
damage, smoke, or fire.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
Do not, under any circumstances, cut or remove
the ground prong from the power cord. To prevent
personal injury or damage to the appliance, the
electrical power cord must be plugged into a
properly grounded outlet. This appliance must
be plugged into a 120VAC, 60-Hz grounced outlet
protected by a 15-ampere fuse or circuit breaker.
Failure to follow these
instructions can result
in fire, explosion, or death.
This appliance must be plugged into a properly
grounded outlet. Electrical shock can result if the
appliance is not properly grounded. Have the wall
outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
Failure to follow these instructions can create an
electric shock hazard and/or a
fire hazard.
Install the appliance where the plug is easily
accessible. Unplug the appliance when not in use
to avoid risk of fire
or electric shock.
Unplug the appliance before disassembly or repair
to avoid risk of electric shock.
The appliance should always be plugged
into its own individual electrical outlet which has a
voltage rating that matches the rating plate. This
provides the best performance and also prevents
overloading house wiring circuits which
could cause a fire
hazard from overheated wires.
Do not use an extension cord to connect
to an outlet. Doing so could
result in a fire
or electric shock. Never unplug
your appliance by pulling on the power cord. Always
grip the plug firmly and pull straight out from the
outlet. The power cord can be damaged, resulting in a
risk of fire and electric shock.
Contact LG or a qualified repair person
immediately to repair or replace all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end. The power cord can
melt, creating electric shock and/or
fire hazard. When installing or
moving the appliance, be careful not to pinch, crush,
or damage the

7
power cord. This will prevent injury and damage
to the appliance from fire
and electric shock.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
WARNING
To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death
when using this appliance, follow basic safety precautions, including the following:
US E
•Do not allow children to play on or in the
appliance. Close supervision of children is
necessary when the appliance is used near
children.
•Do not climb, stand, or hang on the S tyler door
or on the shelf or anywhere inside the appliance.
The appliance could fall over or be damaged, or
other damage or injury could occur.
•Do not step on the doors to the water tanks. The
Styler could fall and cause damage and injury.
•Do not place heavy or dangerous objects on top
of the S tyler.
•Do not put live animals inside the S tyler.
•Do not allow children to climb into the product
when it is in use.
•In the event of a gas leak (propane/LPG), ensure
adequate ventilation and contact an authorized
service center before resuming use. Do not touch
or disassemble the electrical outlet of the Styler.
•Do not use or place flammable substances
(chemicals, medicine, cosmetics, etc) near the S
tyler or store them inside the Styler.
Do not place the Styler in the vicinity of
flammable gas.
•Disconnect the power cord immediately if you
hear a noise, smell a strange odor or detect smoke
coming from the appliance.
•In the event of a flood: Do not go near the
product when its base is submerged under water.
Contact the service center. There is a risk of
electric shock or fire.
•Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
•Do not place hands or body near steam nozzle
during operation. The steam is hot and could
cause an injury.
•Do not insert objects into the steam nozzle.
Excessive noise and fire could result.
•Do not drink the water from the water supply or
drain tanks.
•Do not disassemble or modify the S tyler.
•Do not put hands, feet, or metal objects below
the S tyler.
•Do not operate the S tyler or touch the power
cord with wet hands.
•Keep fingers out of pinch point areas; clearances
between the door and cabinet are necessarily
small. Be careful closing door when children are
nearby.
•This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning the
use of the appliance by a person responsible for
their safety.
•Do not place items exposed to cooking oils in the
S tyler. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause
a load to catch fire.
•Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with

8
gasoline, dry-cleaning solvents, or other
flammable or explosive substances, as they give
off vapors that could ignite or explode.
•Do not use heat to dry articles containing foam
rubber or similarly textured rubber-like materials.
•Do not open door during operation. The
performance of the product may be adversely
affected. If the product is installed on or near
carpet, condensation from escaping hot air or
steam may stain or damage the carpet.
•Do not use the product for other than the
intended purposes. Damage incurred by using the
product for purposes other than those specified in
this user manual are not covered by the warranty.
MAINTENANCE AND DISPOSAL
•Wipe foreign objects (such as dust and water) off
the prongs of the power plug and contact areas
regularly. Do not use a wet or damp cloth when
cleaning the plug.
•Do not use an appliance to dry the interior. Do not
light a candle to remove interior odors.
•Do not spray water onto the product directly
when cleaning. A fire or electric shock may occur.
•Wipe the interior with a dry cloth after use.
•Clean the lint screen before or after each load.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event
of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a
path of least resistance for electric current.
This appliance must be equipped with a cord
having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed
and grounded in accordance with all local codes
and ordinances. Do not modify the plug.
If it will not
fit the outlet, have a
proper outlet installed by a qualified
electrician.
•Do not use a bleaching agent such as oxygen or
chlorine-based bleaches on the exterior of the
product. Clorox or OxiClean may cause
discoloration when applied to the surface of the
product.
•Do not use sharp objects when cleaning or
operating the controls. An electric shock may
occur.
•Avoid hitting the front glass panel with heavy
objects. Although it is made of tempered glass, the
panel may break in the event of a strong impact
and cause injury.
•Keep product free from rodents, insects, and
other foreign objects. They may damage wires,
causing fire or electric shock.
•Before the appliance is removed from service or
discarded, remove the door to the drying
compartment. Cut off the power plug and destroy
the button section to prevent reuse.
WARNING
This product contains chemicals known to the
State of California to cause cancer and birth
defects or other reproductive harm. Wash
hands after handling.
This appliance must be connected to a grounded
metal, permanent wiring system or an
equipment-grounding conductor must be run
with the circuit conductors and connected to the
equipment-grounding terminal or lead on the
appliance. Electric shock can result if the appliance
is not properly grounded.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death when
using this appliance, follow basic safety precautions, including the following:

9
WARNING
Improper connection of the
equipmentgrounding conductor can result in
a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt
that the appliance is properly grounded.
PRODUCT OVERVIEW
PRODUCT OVERVIEW
PARTS

10
* The door swing can be reversed by the installer to fit the installation location.
PRODUCT OVERVIEW
ACCESSORIES
Included Accessories
shelf
MCK67970601
drip tray
AHT74073801
2 rear leveling feet
2 hangers*
AEE73149701 AEE73189601
pants hanger*
AEE73189701
4 carpet install spikes
2 non-skid pads
MHK61866301
2 hinge covers
anti-tip kit wrench 3550JA3143A
*An ordinary metal/plastic hanger can be used if the hook is less than 5/32 in. (4 mm) thick. The hook must fit in the
indentation in the moving hanger snugly. If the fit is too loose, it may result in vibration, noise, and damage to clothing.
NOTE
Contact the store where the product was purchased or LG customer service at 1-800-243-0000 (1-
888-542-2623 in Canada) if any accessories are damaged or missing. Accessories can be purchased
separately online at http://www.lg.com/us

11
For your safety and for extended product life, use only authorized components. The manufacturer is
not responsible for product malfunction or accidents caused by the use of separately purchased
unauthorized components or parts.
The images in this guide may be different from the actual components and accessories, which are
subject to change by the manufacturer without prior notice for product improvement purposes.
PRODUCT OVERVIEW
THE MOVING HANGER
Hang clothes on the moving hanger using the
hangers provided with the Styler, or use any plastic
or metal hanger that hooks snugly into the
indentations in the moving hanger.
•Use the moving hanger for suits, coats, jackets,
blouses, dresses, skirts, and pants that don’t
require a crease. Use the Pants Crease Care to
crease pants.
•Anything that can be securely placed on a hanger
and steamed or dried without retaining hanger
marks or other damage can be placed on the
moving hanger.
•Dry sweaters or knits on the shelf to avoid hanger
marks.
•Clothing should be securely fastened, with
zippers and buttons closed, so that it does not fall
off the moving hanger during the cycle.
•Arrange clothing so it does not touch the sides or
rear of the cabinet, if possible. Condensation may
form on the interior surface of the cabinet, and
items in contact with the surface may remain
damp at the end of the cycle. Hang larger items
on the diagonal indentations on the moving
hanger.
THE PANTS CREASE CARE
Hang clothes in the Pants Crease Care using the
pants hanger provided with the Styler or any pants
hanger that fits into the hooks above the door to the
Pants Crease Care.
•Open the door to the Pants Crease Care by
pressing the icon on the front.
•The Pants Crease Care keeps pants legs creased
while removing wrinkles elsewhere.
•Pants can be pressed while refreshing other items
in the same cycle.
•For optimum results, use the Extra Pants Care
cycle which is designed for use with the Pants
Crease Care feature. This cycle can be
downloaded using the LG Smart Styler app and
used as the Downloaded cycle. For instructions,
see Downloading Styler Cycles, page 36.
CAUTION
Do not lean on or hang heavy items on the
door of the Pants Crease Care. The unit may tip,
resulting in damage or injury. Do not allow

12
children to play with or hang onto the door of
the Pants Crease
CAUTION
Do not lean or pull on the moving hanger. Do
not allow children play with or hang onto
the moving hanger. The unit could tip,
resulting in damage or injury.
Care. The unit may tip, resulting in damage
or injury.
Keep fingers out of pinch point areas when
closing the door of the Pants
C rease C are. Supervise nearby children to
prevent injuries.
PRODUCT OVERVIEW
THE SHELF CHOOSING STYLER FEATURES
item
how to style it
suit coat, blazer
moving hanger
coat, jacket (short)
moving hanger
coat (long)
moving hanger
(remove shelf)
dress (short)
moving hanger
dress (long)
moving hanger
(remove shelf)
skirt
moving hanger
lightweight blanket, throw
moving hanger
baby blanket
moving hanger
pants (not creased)
moving hanger
shorts
moving hanger
children’s clothes
moving hanger
scarf
moving hanger or
shelf
tie
moving hanger or
shelf

13
Use the shelf when styling clothes or other items that are
difficult to hang or that may be damaged by hang drying.
•Use the shelf for stuffed toys, pillows, hats, and other
accessories.
•Use the shelf for sweaters, knits, lingerie, or delicate
blouses that can show hanger marks, stretching, or
other damage if dried on a hanger.
•For best drying performance, do not stack items on
the shelf. Dry single items or place items side by side
with space between.
•When not in use, store the shelf on the shelf holder knobs in the back of the cabinet.
•For instructions on installing the shelf, see Assembling the Shelf, page 28. Do not use the shelf for
storing heavy items.
•Arrange items on the shelf so they do not touch the sides or rear of the cabinet, if possible.
Condensation may form on the interior surface of the cabinet, and items in contact with the surface
may remain damp at the end of the cycle.
CAUTION
Do not use the shelf to store heavy items. The shelf may fall, resulting in damage or injury. Do not
step or sit on the shelf. The shelf may fall or the unit may tip, resulting in damage or injury.
shawl
moving hanger or
shelf
lingerie
moving hanger or
shelf (if delicate)
shirt, blouse
moving hanger or
shelf (if delicate)
pants (creased)
Pants Crease
Care
cap, hat
shelf
stuffed toys
shelf
pillow
shelf
sweater
shelf
knitwear
shelf
infant clothes
shelf

14 INSTALLATION
INSTALLATION
INSTALLATION OVERVIEW
steam clothing care S 3RERB
description
electric machine for maintaining clothing
electrical requirements
please refer to the rating label regarding detailed information
dimensions
17 ½ in. (W) X 23 in. (D) X 72 13/16 in. (H), 39 ¾ in. (D with door open)
445 mm (W) X 585 mm (D) X 1850 mm (H), 1010 mm (D with door open)
net weight
183 lb (83 kg)
maximum capacity
4 items

INSTALLATION 15
Please read the following installation instructions first after purchasing this
product or transporting it to another location.
Install carpet spikes Reverse the door swing Connect to grounded outlet
(if needed) (if needed) PRODUCT
SPECIFICATIONS
The appearance and specifications listed in this manual may vary due to constant product improvements.
UNPACKING THE STYLER •Remove tape and any temporary labels
from the S tyler before using.
WARNING
Use two or more people to move and
install the S tyler. Failure to do so can result in
back injury or other injury.
The S tyler is heavy. Use the wheels at
the bottom of the product to move it. Push the
Styler slowly from about halfway down the front
side.
Keep the S tyler upright when moving
it. If you lay the Styler on its side, refrigerant may
leak and cause the appliance to malfunction. 
Keep flammable materials and vapors, such as
gasoline, away from the S tyler.
Failure to do so can result in fire, explosion, or
death.
Do not remove any warning labels, the model and
serial number label, or the Tech Sheet that is
located under the front of the Styler.
•To remove any remaining tape or glue, rub
the area briskly with your thumb.
Tape or glue residue can also be easily removed
by rubbing a small amount of liquid dish soap
power consumption
1500 W
safety device
double overheating safety device, thermal fuse, programming
proper location

16 INSTALLATION
over the adhesive with your fingers. Wipe with
warm water and dry.
•Do not use sharp instruments, rubbing
alcohol, flammable fluids, or abrasive
cleaners to remove tape or glue.
These products can damage the surface of the
Styler.
CHOOSING THE PROPER LOCATION
Electricity
Install where an outlet is easily accessible.
Use an individual, grounded outlet:120 Volts, 60 Hz, AC, 15 Amps minimum.
WARNING: Do not plug in multiple appliances in the same outlet with the S
tyler. Overloading house wiring can cause a fire hazard.
To reduce the risk of electric shock, do not install the S tyler in a wet or
damp area.
Floor
Floor must be level and solid enough to support 183 lb (83 kg).
Adjust the leveling legs to compensate for any unevenness in the floor.
Do not install on a platform or a weakly supported structure. If installing on
carpeting, see Installing on Carpeting, page 17.
Ambient temperature
Temperature must be between 50°F (10°C) and 95°F (35°C).
If the ambient temperature is too low or high, performance may be affected. Do
not install in direct sunlight or where the temperature may fall below 32°F (0°C).
Clearances
Allow at least 18 in. (46 cm) in front to open the door.
Allow at least 2 in. (5 cm) on both sides and between the back of the Styler and
the wall. Allow at least 7 3/4 in. (20 cm) between the top of the Styler and any
overhanging shelves or cabinets.
If the Styler is too close to adjacent items, performance may decrease and
electricity consumption may increase.
INSTALLATION LOCATION REQUIREMENTS
WARNING Read all installation instructions completely before installing and operating the Styler.
It is important to review this entire manual before installing and using the Styler.
The installation requires:
A grounded electrical outlet located within
2 ft. (61 cm) of either side of the appliance.
A sturdy floor to support the total appliance
weight of 183 lbs (83 kg). The combined weight
of any other laundry appliances should also be
considered.

INSTALLATION 17
WARNING
•Do not install or store the S tyler in an area where it will be exposed to water and/or weather. Failure
to follow this warning could result in risk of electric shock, injury, or product damage or malfunction.
Clearances
CAUTION
•The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the S tyler. If the slope is
greater than 1 inch (2.5 cm), the appliance cannot be leveled properly.
•Do not install the S tyler on a hollow or flexible platform. Doing so may cause excessive noise and
vibration and result in damage or injury if the product tips over.
2 3/64 in.
5 (52 mm)
23
in. (585 mm)

18 INSTALLATION
Recommended Installation Spacing
The following clearances are recommended for the
Styler. Although the Styler has been tested for
clearances of 13/16 inch (3 cm) on the sides and rear,
recommended clearances should be considered for
the following reasons:
Additional space should be considered for ease
of installation and servicing.
Additional space might be required for wall, door
and floor moldings.
Additional space should be considered on all
sides of the Styler to reduce noise transfer.
Additional laundry appliance spacing should also
be considered.
Installation Spacing for Special Cases
Installing the Styler in an area with restricted
clearance and/or ventilation could result in reduced
performance or product damage.
For information on maintaining proper clearances
and ventilation when installing the Styler in closets
or built-in installations with clearances less than
the recommended installation spacing, download
the latest product information from the LG
website at www.lg.com.
in front

INSTALLATION 19
LEVELING THE STYLER
WARNING
To reduce the risk of injury to persons, adhere
to all industry recommended safety procedures
including the use of long-sleeved gloves and
safety glasses.
Failure to follow this warning can cause serious
injury or death.
The appliance is heavy. Two or more people are
required when installing the Styler. Failure to
follow this warning can cause serious injury or
death.
To ensure that the Styler provides optimal
performance, it must be level. To minimize
vibration, noise, and unwanted movement, the
floor must be a perfectly level, solid surface.
Check to make sure
it is level. If
installing on carpet, see
Installing on Carpeting first.
All leveling feet must rest solidly on the floor.
Gently push on the corners of the Styler to make
sure that it does not rock from corner to corner.
Make sure there are no gaps between the front
leveling feet and the floor.
WARNING
The S tyler is heavy. Use two or more
people if installing the rear leveling feet.
Failure to do so can result in back injury or
other injury.
Keep the S tyler upright when moving
and installing it. If you lay the Styler on its
side, refrigerant may leak and cause the
appliance to malfunction.
2 Use the wrench (packaged
with the manual) to
turn the leveling feet.
Unscrew the front feet to raise the Styler or
screw in the feet to lower it. If unable to level
the unit using only the front feet, install the two
rear leveling feet by tipping the unit. Do not lay
the unit down to install the leveling feet.

20 INSTALLATION
REVERSING THE DOOR
It is possible to reverse the direction of the door
swing. This should be done by the installer at the
time of installation, if desired.
WARNING
Do not attempt to reverse the door swing
yourself. If the direction of the door swing needs to
be changed after installation, contact the LG
Customer Information Center at 1-800-243-0000
(USA) or 1-888-542-2623 (Canada).
INSTALLING ON CARPETING
If installing the Styler on carpeting, follow these
instructions.
the back rollers.
2Install the two rear
leveling feet.
Tip the unit, do not lay it down, to install the
leveling feet.
3Level the unit following the
instructions in
Leveling the Styler.
4Install the four carpet
spikes
on the ends of
the leveling
feet, with
the shorter,
octagonalfaces
toward the
front.
front
5After the spikes have been
installed, the Styler may
need to be leveled
again.
If the carpet has very deep pile or padding, the
front feet may need to be extended slightly to
install the drip tray.
WARNING
Take care when handling the carpet
spikes.
They are designed to pierce through the carpet
backing and pad and are very sharp.
Keep fingers and hands out from under
the spikes when setting the unit in place to avoid
personal injury or product damage.
•Be sure to check and empty the drip tray often.
•Do not open the unit during operation to avoid
condensation forming on carpet surface, which
may result in surface mold or mildew.

