LG 32LP1DC User manual

LCD TV
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
OWNER’S MANUAL
MODEL: 32LP1DC
Internet Home Page : http://www.lgcommercial.com
P/NO : 3828TUL309C (0510-REV04)
Printed in Korea

2
Warning
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric
Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac-
tical.
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.
U.S.A. only -----------------------------------------------
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc.
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
Phone: [phone]
http://www.lgusa.com
---------------------------------------------------------------
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
W
Warning arning

3
Safety Instructions
WARNING :
To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong is provided for your safety. When the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the apparatus.
11. Only use the attachments / accessories specified by
the manufacturer.
Safety Instructions
Safety Instructions
Owner's Manual

4
Safety Instructions
Safety Instructions continued
Safety Instructions continued
12. Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving
the cart / apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normal-
ly, or has been dropped.
On Disposal
a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
Note
- If the TV feels cold to the touch, there may be a small “flicker”when when it is turned on. This is normal, there is noth-
ing wrong with TV.
- Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have
no adverse effect on the monitor's performance.
- Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some
temporary distortion effects on the screen.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discon-
tinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

5
Contents
Contents
Contents
Introduction
Installation
Operation
22 Adjustments for screen Position, Clock, and Phase
22 Initializing (Reset to original factory values)
23 Turning on the TV
23 Volume Adjustment
23 Channel Selection
23 On-screen Menus Language Selection
24 Screen Menus Selection and Adjustment
25 EZ Scan (Channel Search)
26 Channel Edit
27 DTV Signal Strength
27 Channel Label Setup
28 Main Picture Source Selection
28 Front LED (Light Emitting Diode) Display
29 EZ Picture
29 Manual Picture Control (EZ Picture-Off Option)
30 XD Function
30 Color Temperature Control
31 Video Preset
32 Audio Language
32 EZ SoundRite
33 EZ Sound
33 Manual Sound Control (EZ Sound-Off Option)
34 Stereo/SAP Broadcasts Setup
34 Front Surround
35 TV Speakers On/Off Setup
2 Warnings
3~4 Safety Instructions
7 Controls
8 Connection Options
9~11 Remote Control Key Functions
12 Various Installation
13 How to use back cover
13 Swivel Stand
14 Antenna Connection
15 External AV Source Setup
15 Digital Audio Output
16 VCR Setup
17 Cable TV Setup
18 DVD Setup
19 HDSTB Setup
20~21 PC Setup
21 Power Cord Connection
Setup Menu
Options
Video Menu
Options
Audio Menu
Options
Screen Setup
for PC mode
Basic operation
External
Equipment
Connections
Installation
Instruction

6
Contents
Reference
36 Auto Clock Setup
36 Manual Clock Setup
37 On/Off Timer Setup
37 Sleep Timer
38 Auto Off
39 Aspect Ratio Control
40 Caption
40 Caption Option
41 Caption Mode
42 Cinema Mode Setup
42 Demo (Review)
43 Split Zoom
44~45 Parental Lock Setup
46 Watching PIP/Double Window
46 Selecting an Input Signal Source for PIP/Double Window
46 TV Program Selection for PIP
47 Moving the PIP sub picture
47 Swapping PIP/Double Window
48~53 External Control Device Setup
54 Programming the Remote Control
55~56 Programming Codes
57~58 Troubleshooting Checklist
59 Maintenance
59 Product Specifications
Option Menu
Features
Lock Menu Options
PIP (Picture-in-
Picture)/
Double Window
Time Menu
Options
Operation

7
Controls
Controls
Introduction
Introduction
- This is a simplified representation of front panel.
- Here shown may be somewhat different from your TV.
CH VOL ENTER MENU ON/OFF
RRAUDIOAUDIO VIDEOVIDEO S-VIDEOS-VIDEO
L/MONOL/MONO
IN2
TV/VIDEO
VOLUME (F,G) Buttons
Power Standby Indicator
Illuminates red when the TV is in standby mode,
illuminates green when the TV is switched on.
Remote Control Sensor
CHANNEL (E, D) Buttons
MENU Button
ENTER Button
ON/OFF Button
Owner’s Manual
/ Commercial Interface
Control Box Manual
2 Bolts
Power Cord D-sub 15 pin Cable 6 Shield Foams
S-VIDEO Input
Audio/Video Input 2
TV/VIDEO Button
Ensure that the following accessories are included with your TV. If any accessory is missing, please contact the
dealer from where you purchased the product.
Accessories
1.5V
1.5V
LIGHT
TV/VIDEO
MODE
COMP/RGB/DVI
MUTESURF
VOLCH
INFO
SAPRATIO
CC
MENU
SOUNDVIDEO
EXIT
PLAYPAUSESTOPRECORD
PIPPIPCH-PIPCH+PIPINPUT
FREEZE
ADJUST
ENTER
ZOOMSIGNALSWAP
REWFF SKIP
POWER
TIMER
FLASHBK
Remote Control /
AA Batteries
Tie Band
Arrange the wires
with the tie band.
Polishing Cloth
Polish the screen with the cloth.

Connection Options
Connection Options
RL
COMPONENT2
VIDEO
Antenna
PC AUDIO
INPUT2
DIGITAL AUDIO
(OPTICAL)
PC INPUT2
DVI INPUT
(PC/DTV INPUT)
L/MONO
PC INPUT1 AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
PC AUDIO
INPUT1
COMPONENT1/DVI
INPUT
SPEAKER
OUT
RS-232C INPUT
(CONTROL/SERVICE)
AC IN
S-VIDEO
AUDIO
RJP INTERFACE
OUTPUT
DIGITAL AUDIO OUTPUT
/ COMPONENT1/DVI INPUT
* PC INPUT2
(For service)
AUDIO/VIDEO INPUT1
COMPONENT1 (Y, PB, PR/ AUDIO INPUT)
COMPONENT2 INPUT
(Y, PB, PR/ Audio Input)
S-VIDEO INPUT
DVI INPUT (PC/DTV INPUT)
ANTENNA INPUT
Power Cord Socket
PC AUDIO INPUT1
* PC AUDIO INPUT2 / SPEAKER OUT
(For service)
* For Service Jacks: PC INPUT2, PC AUDIO INPUT2, SPEAKER OUT, and RJP INTERFACE
Be careful not to use this jack. Just contact your dealer or service center.
PC INPUT1
/ RS-232C INPUT (CONTROL/SERVICE)
* RJP INTERFACE
(For service)
8
Introduction

9
Introduction
Remote Control Key Functions
Remote Control Key Functions
LIGHT
Illuminates the remote control buttons.
TV/VIDEO Selects:
COMP/RGB/DVI Selects:
— (DASH)
Used to enter a program number for multiple program chan-
nels such as 2-1, 2-2,etc.
MODE
Selects the remote operating mode: TV, VCR, DVD, CABLE,
HDSTB or AUDIO. Select other operating modes, for the
remote to operate external devices.
TIMER
Lets you select the amount of time before your TV turns
itself off automatically. (Refer to p.37)
FLASHBK
Return to the last channel viewed.
DTV Analog Video1-2
Component 1-2
RGB1-DTV / RGB1-PC
RGB2-DTV / RGB2-PC
DVI-DTV / DVI-PC
Component 1-2 RGB1-DTV / RGB1-PC
DVI-DTV / DVI-PC RGB2-DTV / RGB2-PC
POWER
Turns your TV or any other programmed equipment on or
off, depending on mode.
NUMBER buttons
LIGHT
TV/VIDEO
MODE
COMP/RGB/DVI
MUTE SURF
VOL CH
INFO
SAP RATIO
CC
MENU
SOUND VIDEO
EXIT
PLAY PAUSE STOP RECORD
PIP PIPCH- PIPCH+ PIPINPUT
FREEZE
ADJUST
ENTER
ZOOM SIGNAL SWAP
REW FF SKIP
POWER
TIMER
FLASHBK

10
Introduction
LIGHT
TV/VIDEO
MODE
COMP/RGB/DVI
MUTE SURF
VOL CH
INFO
SAP RATIO
CC
MENU
SOUND VIDEO
EXIT
PLAY PAUSE STOP RECORD
PIP PIPCH- PIPCH+ PIPINPUT
FREEZE
ADJUST
ENTER
ZOOM SIGNAL SWAP
REW FF SKIP
POWER
TIMER
FLASHBK
MUTE
Switches the sound on or off.
SURF
Use to scroll the Surf channel list.
INFO
When you watch the TV, displays information on top of the screen.
Not available in Component 1-2, RGB 1-2 and DVI mode.
SAP
Selects MTS sound: Mono, Stereo, and SAP. Change the
audio language in DTV mode. (Refer to p.34)
RATIO
Changes the aspect ratio. (Refer to p.39)
CC
Select a closed caption mode: Off, CC1, CC2, CC3, CC4,
Text1, Text2, Text3, or Text4. (Refer to p.41)
THUMBSTICK (Up/Down/Left/Right/ENTER)
Allows you to navigate the on-screen menus and adjust the
system settings to your preference.
MENU
Brings up the main menu to the screen.
SOUND
Selects the sound appropriate for the program's character.
(Refer to p.33)
VIDEO
Adjusts the factory preset picture according to the room.
(Refer to p.29)
EXIT
Clears all on-screen displays and returns to TV viewing from
any menu.
CHANNEL UP/DOWN
Selects available channels found with EZ scan.
VOLUME UP/DOWN
Increases/decreases the sound level.

11
Introduction
INFO
SAP RATIO
CC
MENU
SOUND VIDEO
EXIT
PLAY PAUSE STOP RECORD
PIP PIPCH- PIPCH+ PIPINPUT
FREEZE
ADJUST
ENTER
ZOOM SIGNAL SWAP
REW FF SKIP
PIP
Switches between PIP and Double Window modes.
(Refer to p.46)
PIPCH-/PIPCH+
Changes to next higher/lower PIP channel.
(Refer to p.46)
PIP INPUT
Selects the input source for the sub picture.
(Refer to p.46)
SWAP
Exchanges the PIP/main images. (Refer to p.47)
FREEZE
Freezes the currently-viewed picture. Main picture is frozen
in PIP/Double Window mode.
ZOOM
Enlarges the main picture size. (Refer to p.43)
SIGNAL
Displays the digital signal strength. (Refer to p.27)
ADJUST
Adjusts screen position, clock, and phase in PC mode.
(Refer to p.22)
VCR/DVD BUTTONS
Control some video cassette recorders or DVD player
("RECORD" button is not available for DVD player).
Installing Batteries
Open the battery compartment
cover on the back side.
Insert two 1.5V AA size batteries in
correct polarity (+ with +, - with -).
Don’t mix old or used batteries
with new ones.
Close the cover.
* Point the remote towards the remote
control sensor of the wireless TV and
use it within about 7 meters.
* Put the used batteries into the recy-
cling bin since it can negatively affect
the environment.
LIGHT
TV/VIDEO
MODE
COMP/RGB/DVI
POWER
TIMER
1
2
3

12
Installation
Installation
Installation
Various Installation
4 inches
4 inches
4 inches4 inches
2 inches
For proper ventilation, allow a clearance of 4" on each side
and 2" from the wall. Detailed installation instructions are
available from your dealer, see the optional Tilt Wall
Mounting Bracket Installation and Setup Guide.
Wall Mount: Horizontal installation
Desktop Pedestal Installation
4 inches
4 inches4 inches
2 inches
For proper ventilation, allow a clearance of 4" on each side
and the top, and 2" from the wall.

13
Installation
How to use back cover
- The TV can be conveniently swivelled on its stand 90°
to the left or right to provide the optimum viewing
angle.
Swivel Stand
34
2Install wires as necessary.
(To install various wires, refer to p.14~21.)
Align the holes on the TV back panel with the
four protuberance on the back cover and
insert.
Antenna
LOOPTHROUGH
UPGRADE
PORT
HDMI MONITOR
OUT
REMOTE
CONTROL
DVIINPUT
(PC INPUT)
PC SOUND
AV1 AV2
VIDEO
L
AUDIO
R
Reinstall the cover.
Antenna
LOOPTHROUGH
UPGRADE
PORT
HDMI MONITOR
OUT
REMOTE
CONTROL
DVIINPUT
(PC INPUT)
PC SOUND
AV1 AV2
VIDEO
L
AUDIO
R
Wire Arrangement
- Pull the cables through
the hole on the set.
Antenna
LOOPTHROUGH
UPGRADE
PORT
HDMI MONITOR
OUT
REMOTE
CONTROL
DVIINPUT
(PC INPUT)
PC SOUND
AV1 AV2
VIDEO
L
AUDIO
R
Hold the back cover with both hands and
pull it backward.
1
* Arrange the signal input cable and the power
cord by holder, as shown.
Install the 2 bolts to prevent
the detachment between TV
and back cover.
Antenna
UPGRADE
PORT
HDMI MONITOR
OUT
REMOTE
CONTROL
DVI INPUT
(PCINPUT)
PCSOUND
AV1 AV2
VIDEO
L
AUDIO
R

14
Installation
NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-
type searches. The TV will let you know when the analog, cable, and digital channel scans are complete.
External Equipment Connections
External Equipment Connections
Antenna Connection
- Antenna or Cable Service without a Cable Box Connections.
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor Antenna
Wall Antenna Socket
VHF Antenna
UHF Antenna
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
•In a poor signal area to improve picture quality, purchase
and install a signal amplifier.
•If the antenna needs to be split for two TV’s, install a “2-
Way Signal Splitter”in the connections.
•If the antenna is not installed properly, contact your deal-
er for assistance.
Antenna
Antenna
L/MONO
INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
L
R
VIDEO
Bronze Wire
Be careful not to bend the bronze wire when
connecting the antenna.
Signal
Amplifier

15
Installation
Digital Audio Output
RAUDIO VIDEOS-VIDEO
L/MONO
IN2
RL
AUDIO VIDEO
Camcorder
Video Game Set
TV Front 1
1
2
3
Connect the AUDIO/VIDEO jacks between TV
and external equipment. Match the jack colours
(Video = yellow, Audio Left = white, and Audio
Right = red).
Select Video 2 input source with using the
TV/VIDEO button on the remote control.
- If connected to VIDEO1 input (the back side),
select Video 1 input source.
Operate the corresponding external equipment.
Refer to external equipment operating guide.
1
2
3
Connect one end of an optical cable to the TV
Digital Audio Optical Output port.
Connect the other end of the optical cable to the
digital audio optical input on the audio equipment.
Set the “TV peaker option - Off”in the AUDIO
menu. Refer to page 35.
See the external audio equipment instruction
manual for operation.
DIGITAL AUDIO
(OPTICAL)
PC INPUT2
DVI INPUT
(PC/DTV INPUT)
L/MONO
PC INPUT1 AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
RS-232C INPUT
(CONTROL/SERVICE)
S-VIDEO
OUTPUT
COMPONENT1/DVI
INPUT
- Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.
CAUTION
Do not look into the optical output port. Looking
at the laser beam may damage your vision.
External AV Source Setup
1/2 TV Back

16
Installation
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
- Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides
of the screen may remain visible on the screen.
VCR Setup
NOTE: All cables shown are not included with the TV.
When connecting with an antenna
1
2
3
4
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
34
OUTPUT
SWITCH
ANT OUT
ANT IN
DVI INPUT
(PC/DTV INPUT)
Connect the RF antenna out socket of the VCR to
the Antenna socket on the set.
Connect the antenna cable to the RF antenna in
socket of the VCR.
Set VCR output switch to 3 or 4 and then tune TV
to the same channel number.
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.)
TV Back
VCR
When connecting with a RCA cable
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
34
OUTPUT
SWITCH
ANT OUT
ANT IN
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
DVI INPUT
(PC/DTV INPUT)
VCR
TV Back 1
2
3
Connect the AUDIO/VIDEO jacks between TV
and VCR. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.)
Select Video1 input source with using the
TV/VIDEO button on the remote control.
- If connected to IN 2 input (TV front), select
Video2 input source.
•If you have a mono VCR, connect the audio cable
from the VCR to the AUDIO L/MONO jack of the set.
When connecting with an S-Video cable
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
34
OUTPUT
SWITCH
ANT OUT
ANT IN
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
DVI INPUT
(PC/DTV INPUT)
VCR
TV Back 1
1
2
2
3
4
Connect the an S-VIDEO output of the VCR to the
S-VIDEO input on the set. The picture quality is
improved; compared to connecting a regular VCR
to the Video input.
Connect the audio outputs of the VCR to the
AUDIO input jacks on the set.
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.)
Select Video 1 input source with using the
TV/VIDEO button on the remote control.
- If connected to IN2 input (TV front), select
Video2 input source.
Do not connect to both Video and S-Video at
the same time.
1
2
1

17
Installation
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch
cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV
converter box is connected to the TV.
- For further information regarding cable TV service, contact your local cable TV service provider(s).
Cable TV Setup
When connecting with an antenna
1
2
3
5
4
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
TV
VCR RF Cable
(R) AUDIO (L)
VIDEO
34
OUTPUT
SWITCH
DVI INPUT
(PC/DTV INPUT)
Connect the RF antenna socket of the cable box
to the Antenna socket on the set.
Connect the antenna cable to the RF antenna
socket of the cable box.
Select 3 or 4 with channel switch on the cable box.
Tune the TV channel to the same selected output
channel on the cable box.
Select channels at the cable box or with the cable
box remote control.
When connecting with a RCA cable
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
TV
VCR RF Cable
(R) AUDIO (L)
VIDEO
34
OUTPUT
SWITCH
DVI INPUT
(PC/DTV INPUT)
1
2
3
Connect the AUDIO/VIDEO jacks between TV
and VCR. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
Select Video1 input source with using the
TV/VIDEO button on the remote control.
- If connected to IN 2 input (TV front), select
Video2 input source.
Select your desired channel with the remote con-
trol for the cable box.
TV Back
Cable Box
1/2
Cable Box
TV Back
1

18
Installation
NOTE: All cables shown are not included with the TV
DVD Setup
When connecting with a S-Video cable
S-VIDEO (R) AUDIO (L)
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
DVI INPUT
(PC/DTV INPUT)
DVD
TV Back 1
1
2
2
3
4
5
Connect the S-VIDEO output of the DVD to the
S-VIDEO input on the set.
Connect the audio outputs of the DVD to the
AUDIO input jacks on the set.
Turn on the DVD player, insert a DVD.
Select Video1 input source with using the
TV/VIDEO button on the remote control.
- If connected to IN 2 input (TV front), select
Video 2 input source.
Refer to the DVD player's manual for operating
instructions.
When connecting with a component cable
1
3
4
5
Connect the video outputs (Y, PB, PR) of the DVD
to the COMPONENT1 VIDEO (Y, PB, PR)jacks
on the set.
Connect the audio outputs of the DVD to the
COMPONENT1 AUDIO jacks on the set.
Connect the optical audio output of the DVD to
the DIGITAL AUDIO COMPONENT1/DVI INPUT
jack on the set.
Turn on the DVD player, insert a DVD.
Select Component 1 input source with using the
TV/VIDEO or COMP/RGB/DVI button on the
remote control.
- If connected to COMPONENT2 (TV side), select
Component 2 input source.
Refer to the DVD player's manual for operating
instructions.
•Component Input ports
To get better picture quality, connect a DVD player
to the component input ports as shown below.
•Digital Audio will not work for Component 2 input
source.
•Digital Audio operation has priority if Digital Audio
and AUDIO L/R are connected at the same time.
Y PBPR
Component ports on the TV
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
Video output ports
on DVD player
BR
(R) AUDIO (L)
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
DVI INPUT
(PC/DTV INPUT)
DIGITAL AUDIO
OPTICAL
DIGITAL AUDIO
(OPTICAL)
OUTPUT
COMPONENT1/DVI
INPUT
DVD
TV Back
1
Select or , depending on your DVD
connector.
2-1
2-1
2-1 2-2
2-2
2-2

19
Installation
When connecting with a D-sub 15 pin cable
1
2
3
4
Connect the RGB output of the digital set-top box
to the PC INPUT1 jack on the set.
Connect the audio outputs of the set-top box to
the PC AUDIO INPUT1 jack on the set.
Turn on the digital set-top box. (Refer to the
owner’s manual for the digital set-top box.)
Select RGB1-DTV input source with using the
TV/VIDEO or COMP/RGB/DVI button on the
remote control.
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if
you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure
as shown below.
RGB-DTV OUTPUT
(R) AUDIO (L)
PC AUDIO
INPUT2
DIGITAL AUDIO
(OPTICAL)
PC INPUT2
PC INPUT1
PC AUDIO
INPUT1
SPEAKER
OUT
RS-232C INPUT
(CONTROL/SERVICE)
AC IN
OUTPUT
COMPONENT1/DVI
INPUT
Digital Set-top Box
HDSTB Setup
TV Back
When connecting with a Component cable
1
2
3
4
Connect the video outputs (Y, PB, PR) of the digi-
tal set-top box to the COMPONENT1 VIDEO
INPUT (Y, PB, PR)jacks on the set.
Connect the audio outputs of the digital set-top
box to the COMPONENT1 AUDIO INPUT jacks
on the set.
Turn on the digital set-top box. (Refer to the
owner’s manual for the digital set-top box.)
Select Component 1 input source with using the
TV/VIDEO or COMP/RGB/DVI button on the
remote control.
- If connected to COMPONENT2 input (TV side) ,
select Component 2 input source.
BR
(R) AUDIO (L)
Antenna
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
DVI INPUT
(PC/DTV INPUT)
Signal
480i
480p/720p/1080i
Component1/2
Yes
Yes
RGB-DTV, DVI-DTV
No
Yes
When connecting with a DVI cable
1
2
3
4
Connect the DVI output of the digital set-top box to
the DVI INPUT (PC/DTV INPUT) jack on the set.
Connect the digital audio outputs of the set-top
box to the DIGITAL AUDIO COMPONENT1/DVI
INPUT jack on the set.
Turn on the digital set-top box. (Refer to the
owner’s manual for the digital set-top box.)
Select DVI-DTV input source with using the
TV/VIDEO or COMP/RGB/DVI button on the
remote control.
Antenna
DVI-DTV OUTPUT
DIGITAL AUDIO
OPTICAL
DIGITAL AUDIO
(OPTICAL)
L/MONO
OUTPUT
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
DVI INPUT
(PC/DTV INPUT)
COMPONENT1/DVI
INPUT
Digital Set-top Box
TV Back
1
2
1
2
TV Back
Digital Set-top Box
1
2

20
Installation
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association
(VESA) Display Data Channel (DDC) protocol.
PC Setup
When connecting with a D-sub 15 pin cable
When connecting with a DVI cable
1
2
3
4
Connect the RGB output of the PC to the PC
INPUT1 jack on the set.
Connect the PC audio outputs to the PC AUDIO
INPUT1 jack on the set.
Turn on the PC and the set.
Select RGB1-PC input source in main input
option of SETUP menu. (Refer to P.28)
1
2
3
4
Connect the DVI output of the PC to the DVI
INPUT (PC/DTV INPUT) jack on the set.
Connect the PC audio outputs to the DIGITAL
AUDIO COMPONENT1/DVI INPUT jack on the set.
Turn on the PC and the set.
Select DVI-PC input source in main input option
of SETUP menu. (Refer to P.28)
DIGITAL AUDIO
OPTICAL
Antenna
DIGITAL AUDIO
(OPTICAL)
DVI INPUT
(PC/DTV INPUT)
L/MONO
AUDIO INPUT
AUDIO VIDEO
VIDEO INPUT
VIDEO1
COMPONENT1
RL
R
S-VIDEO
OUTPUT
COMPONENT1/DVI
INPUT
DVI-PC OUTPUT
RGB-PC OUTPUT
AUDIO
PC AUDIO
INPUT2
DIGITAL AUDIO
(OPTICAL)
PC INPUT2
PC INPUT1
PC AUDIO
INPUT1
SPEAKER
OUT
RS-232C INPUT
(CONTROL/SERVICE)
AC IN
OUTPUT
COMPONENT1/DVI
INPUT
1
2
1
2
TV Back
PC
TV Back
PC