LG 32LN549C User manual

www.lg.com
OWNER’S MANUAL
LED TV
PUBLIC DISPLAY MODE SETUP
Please read this manual carefully before operating your set and retain it
for future reference.
32LN549C
42LN549C
47LN549C
32LP360H
42LP360H

2
ENG
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your
product.
 Do not use this apparatus near water.
Short-circuit
Breaker
Power Supply
 Clean only with a dry cloth.
Short-circuit
Breaker
Power Supply
 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Short-circuit
Breaker
Power Supply
 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Short-circuit
Breaker
Power Supply
 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet (Can differ by
country).
Short-circuit
Breaker
Power Supply
 Do not press strongly upon the panel with a hand or
a sharp object such as a nail, pencil or pen, or make
a scratch on it.
Short-circuit
Breaker
Power Supply
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may be
seriously injured or there is a possibility of accident
or death.
CAUTION
If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the product
safely. Please read the note carefully before using
the product.
Short-circuit
Breaker
Power Supply

3
ENG
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
 Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Short-circuit
Breaker
Power Supply
 Only use attachments/accessories specified by the
manufacturer.
Short-circuit
Breaker
Power Supply
 Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Short-circuit
Breaker
Power Supply
 Unplug this apparatus during lightning storms or
when unused for long periods of time.
Short-circuit
Breaker
Power Supply
 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Short-circuit
Breaker
Power Supply
 Do not stick metal objects or any other conductive
material into the power cord. Do not touch the end
of the power cord while it is plugged in.
 Keep the packing anti-moisture material or vinyl
packing out of the reach of children. Anti-moisture
material is harmful if swallowed. If swallowed
by mistake, force the patient to vomit and visit
the nearest hospital. Additionally, vinyl packing
can cause suffocation. Keep it out of the reach of
children.
 CAUTION concerning the Power Cord
(Can differ by country):
It is recommended that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner’s manual to be certain. Do
not connect too many appliances to the same AC
power outlet as this could result in fire or electric
shock. Do not overload wall outlets. Overloaded
wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and
if its appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part
by an authorized service. Protect the power cord
from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance. Do
not move the TV with the power cord plugged in.
Do not use a damaged or loose power cord. Be sure
do grasp the plug when unplugging the power cord.
Do not pull on the power cord to unplug the TV.
Short-circuit
Breaker
Power Supply
 Warning - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles, or expose the
TV to direct air conditioning.
Short-circuit
Breaker
Power Supply
 Do not expose to dripping or splashing and do not
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).
Short-circuit
Breaker
Power Supply

4
ENG
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
 Grounding
(Except for devices which are not grounded.)
Ensure that you connect the earth ground wire to
prevent possible electric shock (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grounded AC outlet). If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not
try to ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
Short-circuit
Breaker
Power Supply
 As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
 Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
 Outdoor Antenna Grounding (Can differ by country):
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power circuits,
or where it can come in contact with such power
lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges. Section 810 of the
National Electrical Code (NEC) in the U.S.A. provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Short-circuit
Breaker
Power Supply
Ground Clamp
Grounding Conductor
(NEC Section 810-21)
Antenna Lead in Wire
Electric Service
Equipment
Antenna Discharge Unit
(NEC Section 810-20)
Ground Clamp
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
NEC: National Electrical Code
 Cleaning
When cleaning, unplug the power cord and wipe
gently with a soft cloth to prevent scratching. Do
not spray water or other liquids directly on the TV
as electric shock may occur. Do not clean with
chemicals such as alcohol, thinners or benzine.
 Moving
Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press or put
stress on the front panel of the TV.
 Ventilation
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other
materials while plugged. Do not install in excessively
dusty places.
 If you smell smoke or other odors coming from
the TV, unplug the power cord and contact an
authorized service center.
 Keep the product away from direct sunlight.
 Never touch this apparatus or antenna during a
thunder or lightning storm.
 When mounting a TV on the wall, make sure not
to install the TV by hanging the power and signal
cables on the back of the TV.
 Do not allow an impact shock or any objects to fall
into the product, and do not drop anything onto the
screen.
 Disconnecting the Main Power
The power outlet used with this device must remain
easily accessible.
 Store the accessories (battery, etc.) in a safe
location out of the reach of children.
 This apparatus use batteries. In your community
there might be regulations that require you
to dispose of these batteries properly due to
environmental considerations. Please contact your
local authorities for disposal or recycling information.
 Do not dispose of batteries in a fire.
 Do not short circuit, disassemble or allow the
batteries to overheat.

5
ENG
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
 Dot Defect
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.
 Generated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated by
plastic thermal contraction due to temperature and
humidity. This noise is common for products where
thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level
noise is generated from a high-speed switching
circuit, which supplies a large amount of current
to operate a product. It varies depending on the
product.
This generated sound does not affect the
performance and reliability of the product.
 Take care not to touch the ventilation openings.
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or cause
defects in the product.
 If the TV feels cold to the touch, there may be a
small “flicker” when it is turned on. This is normal,
there is nothing wrong with TV. Some minute dot
defects may be visible on the screen, appearing as
tiny red, green, or blue spots. However, they have
no adverse effect on the TV’s performance. Avoid
touching the LCD screen or holding your finger(s)
against it for long periods of time. Doing so may
produce some temporary distortion effects on the
screen.
Preventing “Image burn” or “Burn-in” on your TV
screen
 If a fixed image displays on the TV screen for a long
period of time, it will be imprinted and become a
permanent disfigurement on the screen. This is
“image burn” or “burn-in” and not covered by the
warranty.
 If the aspect ratio of the TV is set to 4:3 for a
long period of time, image burn may occur on the
letterboxed area of the screen.
 Avoid displaying a fixed image on the TV screen for
a long period of time (2 or more hours for LCD, 1
or more hours for the Plasma TV) to prevent image
burn.

6
ENG
ENGLISH
TABLE OF CONTENTS / INSTALLATION MENU
TABLE OF CONTENTS
6 TABLE OF CONTENTS
6 INSTALLATION MENU
6 ENTERING THE INSTALLATION MENU
7 PUBLIC DISPLAY SETUP
9 USB Cloning
11 Changing the Password
11 Set ID Setup
INSTALLATION MENU
Your TV's OSD (On Screen Display) may differ
slightly from that shown in this manual.
ENTERING THE
INSTALLATION MENU
The feature set up available on this LG commercial
TV which is equipped with ‘USB Cloning’ as
shown on the ‘Installation Menu’. This simple
menu is designed to make it easy and efficient
for the system integrator to install and set up the
institution’s communications system.
Public Display Mode controls operation and
functionality of the TV. Once set up, these settings
are clonable; they can be copied and transferred to
another identical TV. See the USB Cloning section
for cloning details.
Accessing the Installation Menu
with the Menu Button
1 With an LG installer remote, press and hold
down the MENU button for five seconds. The
TV screen will show the Channel on-screen
display in the upper-left corner.
2 Key in “1-1-0-5” and press the OK button. This
is the default password. The password can be
changed if desired.
Accessing the Public Display Mode
Menu
1 Use the
v or
^
button to select the Public
Display Settings option and press the OK
button.
2 Once in the Public Display Settings menu,
use the
v
^
< > button to select and adjust
the menu options to your requirements. If you
want Public Display mode to be enabled, select
‘Yes’ for that option.
Installation Menu (V 2.6)
Public Display Settings
USB Cloning
Password Change
Set ID Setup
Configuration Setup
OK

7
ENG
ENGLISH
INSTALLATION MENU
PUBLIC DISPLAY SETUP
Refer to the PDM menu options as described
below and on the following page. Then set the
options to your requirements.
1 Use the v or ^ or < or > button to select
desired menu option.
2 Use the OK button to return to previous menu.
3 Use the OK button to exit menu.
Installation Menu (V 2.6)
Public Display Settings
USB Cloning
Password Change
Set ID Setup
Configuration Setup
OK
Public Display Mode Menu Items
Public Display Settings
ꔊ Yes ꔋ
Yes
TV
Virtual
12
2
No
AV1
Enable
0
100
No
15
No
7
0
0
0
OK
• Public Display Mode
• Power On Defult
• Input Source
• Tune Mode
• Major
• Minor
• Aux Source Setting
• Input Source
• Setting
• Minimum Volume
• Maximum Volume
• Start Volume
• Level
• Power Management
• Setting
• Key Management
• Factory Reset
• Aspect Ratio
Previous
ꕣ
Public Display Mode
If ‘Public Display Mode’ is set to Yes (Enabled), all
functions of the Public Display Settings are active.
If ‘Public Display Mode’ is set to No (Disabled), all
functions of the Public Display mode are not active.
Power On Default
This function allows you to determine the initial channel
number and external input when the TV is turned
On. This feature is useful for an in-house information
channel, since the TV would always select that channel
when it is turned On. When set to No, the TV starts on
the channel it was on before turning off.
Aux Source Setting
The Aux Source Setting feature will enable or
disable each external input. This data will be
retained in non-volatile memory and will survive a
power loss.
Minimum Volume
This function determines the minimum volume level
allowable with the VOLUME (VOL) Up/Down control. In
this way, for example, someone cannot set the volume
too low to hear. The value range is from 0 to 100 —
change values with ADJ Left/Right arrow. The factory
default is 0, which provides the full range of volume
control, if item 009 MAX VOLUME is also set to 100. It
may be best to set the same value on every TV.
NOTE: The minimum volume level cannot have a value
setting higher than the MAX VOLUME level (described
below).
Maximum Volume
This function determines the maximum volume
level allowable with the VOLUME (VOL) Up/Down
controls. In this way, for example, someone can not
set the volume level high enough to disturb others.
The value range is 0 to 100, with 100 as the default,
which gives the user the full range of volume control,
if item 008 MIN VOLUME is also set at 0. Change
values with ADJ Left/Right arrow keys. It may be
best to set the same value on every TV.
NOTE: The maximum volume level cannot have a
value setting lower than the MIN VOLUME level
(described previously).
Start Volume
This function allows the Installer to determine
the initial volume level setting when the TV is
turned ON. This feature is useful for an in-house
information channel, since the TV would always
select that Volume level when it is turned on. The
range of values are 0 - 100. If No is selected, the
current volume level will be retained in memory
when the TV is turned Off. At TV turn On, Volume
level is automatically set to the previous level.
Setting is retained in non-volatile memory.
Level
The level means start volume level. (0 ~ 100)

8
ENG
ENGLISH
INSTALLATION MENU
Power Management
Determines hours of no activity before automatic
shutoff. The POWER MANAGE function is for
saving energy. If set to No, Power Manage is
disabled. Settings range from 1 ~ 7, representing
the hours that the unit will remain On, unless
there has been activity from either the control
panel or remote control. Setting is retained in non-
volatile memory.
Setting
The setting is a value between 1 and 7
corresponding to the number of hours desired.
Key Management
If set to 1, key defeat prevents the end user from
accessing the on-screen menus with the display
front panel-SETTINGS button do not function.
Note: The menus can always be accessed by
pressing MENU button on the remote.
Key management when enabled determines
the level of control that the guest has over the
television. Key management has five modes:
(default is ‘0’)
0 = Television is unrestricted and responds to
all commands.
1 = "Key defeat”prevents the television from
responding to “MENU”key presses on the
front panel.
2 = “Key Lock”prevents the television from
responding to any front panel key press.
3 = “System provider”mode allows access to
the menu system from the front panel or
remote control but access is controlled as
follows
* Accessible items on the menu system
- Main/PIP input select screens
- Sleep Timer
- Aspect Ratio
- Closed Caption
- Full access “Lock”
→
Q.menu, related to “Setup Menu”, is not
accessible either.
4 = “Key defeat” prevents the TV from
responding to a “MENU” button pressed
on the front panel and remote control.
5 = “No access Remote/Front panel” prevents
the TV from responding to any button
pressed on the front panel and remote
control.
NOTE: You must set the Auto Off option to
off in the Time menu to prevent the TV set
from being turned off automatically.
Setting is retained in non-volatile memory.
Factory Reset
Set to 0 for normal.
Set to 1 to load presets to all of the previous item
settings and exit menu.
WARNING: Setting this to 1 will reload the factory
defaults.
Setting is retained in non-volatile memory.
Aspect Ratio
Selects default aspect ratio at power up, see
settings below.
Set to 0 to disable. Aspect Ratio will stay at
previous state.
Set to 1 “Set By Program”.
Set to 2 for 4:3.
Set to 3 for 16:9.
Setting is retained in non-volatile memory.
Item Enable Disable Initial
Public Display Mode Yes No No
Power On default Yes No No
Input Source TV-MAX_INPUT TV
Tune Mode Virtual/Physical Physical
Major No. Subject to Ch. Type 2
Minor No. Subject to Ch. Type 0
Aux Input Source Setting Yes No No
Input Source
Aux Input (AV1-Max_Input) AV1
Setting Enable / Disable Enable
Minimum Volume 0 ~ 100 0
Maximum Volume 0 ~ 100 100
Start Volume Yes No No
Level 0 ~ 100 20
Power Management Yes No No
Setting 1 ~ 7 1
Key Management 0 ~ 5 0
Factory Reset 0 ~ 1 0
Aspect Ratio 0 ~ 3 0

9
ENG
ENGLISH
INSTALLATION MENU
USB Cloning
An Installer can quickly set up and clone multiple
TV sets at a property. These cloned TVs will all
have the same Master TV Setup: Public Display
Mode Installation Menu settings, User A/V settings
and the Channel Map. This newer procedure
significantly decreases the installation time.
Receive from USB
* USB Restriction: NTFS format is not supported.
1 Plug USB memory card into the USB port of the TV.
2 Use the v or ^ button to select the USB
Cloning option and then press the OK button.
Installation Menu (V 2.6)
Public Display Settings
USB Cloning
Password Change
Set ID Setup
Configuration Setup
OK
3 Use the v or ^ button to select the Receive
from USB and press the OK button.
• Below explains the naming rules for .TTL files
The supported model line will be in the name
of the file but the screen size will be listed as
"xx".
This allows TVs having the same chassis
model number to use the same ‘*.TTL’ file
without regard to the screen size.
ex) The name of ‘*.TTL’ file is ‘xxLH200C-
UA00000.TLL’ for 32/37/42LH200C model.
USB Cloning
Receive from USB
Send to USB
Logo Image Download
OK
Previous
ꕣ
4 Use the v or ^ button to select the desired
*.TLL files name and press the OK button.
Receive from USB
xxLH200C-UA00001.TLL
xxLH200C-UA00002.TLL
xxLH200C-UA00003.TLL
OKPrevious
ꕣ
5 The TV is changed to Standby mode after a
successful download.
If the download failed, the TV will changed to
the initial installation screen.
Send to USB
* USB Restriction: NTFS format is not supported.
1 Plug the USB memory card into the USB port
of the TV.
2 Use the v or ^ button to select the USB
Cloning option and then press the OK button.
Installation Menu (V 2.6)
Public Display Settings
USB Cloning
Password Change
Set ID Setup
Configuration Setup
OK
3 Use the v or ^ button to select the Send to
USB and press the OK button.
USB Cloning
Receive from USB
Send to USB
Logo Image Download
OK
Previous
ꕣ
4 Use the v or ^ button to select the desired file
mane and press the OK button.
Send To USB
Select the file name and press OK to start
ꔠ
ꔡ
xxLH200C-UA00001.TLL
OK
Previous
ꕣ
5 The TV is changed to the initial installation
screen after a successful download.

10
ENG
ENGLISH
INSTALLATION MENU
Logo Image Download
Make a ‘LG_DTV’ folder on the USB flash drive
and then copy the splash image file to that folder.
1 Connect the USB device to the USB IN jack on
the TV.
IN 3
H/P USB IN
AV IN 2
VIDEO
AUDIO
L/MONO
R
ANTENNA/
CABLE IN
RGB IN (PC)
AUDIO IN
(RGB/DVI)
RS-232C IN
(CONTROL &
SERVICE)
OPTICAL
DIGITAL
AUDIO OUT
VIDEO
AUDIO
L/MONO
R
VIDEO AUDIO
COMPONENT IN
AV IN 1
Y PBPRL R
1
2
/DVI IN
IN 3
H/P USB IN
AV IN 2
VIDEO
AUDIO
L/MONO
R
ANTENNA/
CABLE IN
RGB IN (PC)
AUDIO IN
(RGB/DVI)
RS-232C IN
(CONTROL &
SERVICE)
OPTICAL
DIGITAL
AUDIO OUT
VIDEO
AUDIO
L/MONO
R
VIDEO AUDIO
COMPONENT IN
AV IN 1
Y PBPRL R
1
2
/DVI IN
2 Use the v or ^ button to select the USB
Cloning option and then press the OK button.
Installation Menu (V 2.6)
Public Display Settings
USB Cloning
Password Change
Set ID Setup
Configuration Setup
External Speaker
OK
3 Use the v or ^ button to select Logo Image
Download and press the OK button.
USB Cloning
Receive from USB
Send to USB
Logo Image Download
OK
Previous
ꕣ
4 Use the v or ^ button to select the desired file
name and press the OK button.
Logo Image Download
Image1.jpg
Image2.jpg
Image3.jpg
OKPrevious
ꕣ
5 Wait till the download process is completed.
After completion of download, TV set will
restart automaticallly.
!
?
!
?
TV Software Upgrade
UPGRADING...
100%
Do not unplug!
6 You can see a new Splash Image on TV which
you downloaded while turning on TV.
INPUT MENU VOL CH ENTER
NOTE
 Splash Image update function supports only
JPEG format file of less than 1 MB filesize.
 JPEG images with progressive encoding are
not supported.
 We recommend you that splash image
resolution match the TV`s panel resolution.
 Max resolution of splash image: Full HD ->
1920 x 1080, HD -> 1360 x 768.
 The TV will keep the Splash image until you
change it.

11
ENG
ENGLISH
INSTALLATION MENU
Changing the Password
If security for the system is a critical issue, the
password can be changed.
1 Use the v or ^ button to select the Password
Change option and then press the OK button.
 If the password is incorrect, the TV will
return to the installation menu (This feature
is not available for all models).
2 Key in a new four number password, key in the
password again for confirmation.
 The password cannot be “8-7-4-1”. That
sequence of numbers is used to enter the
calibration menu (This feature is not available
for all models).
Password Change
New Password
Confirm Password
OK
*
** *
* * **
Previous
ꕣ
Set ID Setup
1 Use the v or ^ button to select the Set ID
Setup option and then press the OK button.
2 Select Yes to enable Set ID Lock or No to
disable Set ID Lock.
3 Key in a set ID number 1 ~ 99.
Set ID Setup
Set ID Lock
Set ID
OK
◀ Yes ▶
1
Previous
ꕣ
Configuration setup
1 Select RCU (Remote Control Unit)
 It is a mode to set whether to use Select
RCU or not. When ‘Select RCU’ is set to
‘Enable’, You can adjust the ‘Number of
RCU’ menu.
2 Number of RCU
 It is a mode to set the Number of RCU.
Number of RCU value range 1 ~ 9 (When
‘Select RCU’ is set to ‘Enable’)
Number of RCU value range 0 (When ‘Select
RCU’ is set to ‘Disable’)
* RCU (Remote Control Unit): It is special RCU
that operates only a set number of RCU in the
TV.
3 Splash Offset Time
 Sets the splash image display time.
 The time can be set to between 0 and 10
seconds.
4 USB Auto playback
 When 'USB Auto Playback' is 'Enable', TV
finds and plays USB's movie files located
at the first slot and partition and root(top)
directory movies if USB is pluggedin. (Some
menu OSDs may prevent this function.)
 When the TV is on, the TV will search
the USB's movie files and play them,
automatically.
 If it reaches the last file, it starts the first file
again.
5 Auto Sensing (For LP360H Only)
 Select ‘Aux Source Setting – Yes’ to use
‘Auto Sensing’ function (See page 7). If 'Auto
Sensing' is set to 'To Set ⊙', the input is
automatically switched when the input signal
that you set to 'ON' is received .
 If 'Auto Sensing' is set to 'Disable', the input
is not switched when the input signal is
received .
 TV can display the switched input depends
on connected device’s display availability.
 SIMPLINK and Auto Sensing cannot work
simultaneously. If SIMPLINK is set to On,
Auto Sensing is automatically set to Disable.
 If the signal is removed while Auto Sensing
(automatic input switch) is enabled, the input
returns to the previous setting .
 If the several inputs are connected by
enabling Auto Sensing and the automatic
input switch is performed several times, the
input returns to the previous setting only
for the last input and does not repeat the
operation for the rest.
Configuration Setup
Select RCU
Number of RCU
Splash Offset Time
USB Auto Playback
Auto Sensing
Enable
1
0
OK
Previous
ꕣ
Disable
Disable

The model and serial number of the TV is
located on the back and/or one side of the TV.
Record it below should you ever need service.
MODEL
SERIAL