LG SDM-S74 User manual

COLOR MONITOR
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS NO. : CL-42
MODEL: SDM-S74, SDM-S94

1. LCD CHARACTERISTICS
Type : TFT Color LCD Module
Size : 17 inch (SDM-S74)
19 inch (SDM-S94)
Pixel Pitch :
0.264 (H) x 0.264 (V)
(SDM-S74)
0.294 (H) x 0.294 (V) (SDM-S94)
Color Depth : 16.2M colors (SDM-S74)
16.7M colors (SDM-S94)
Electrical Interface : LVDS
Surface Treatment : Haze 25%, Hard-coating(3H)
Operating Mode : Normally White (SDM-S74)
Black (SDM-S94)
Backlight Unit : Top/Bottom edge side 4-CCFL
(Cold Cathode Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥ 10
(SDM-S74)
Left : -60° min., -70°(Typ) Right : +60° min., +70°(Typ)
Top :+45° min., +60°(Typ) Bottom : -45°min., -60°(Typ)
(SDM-S94)
Left : -85° min. Right : +85° min.
Top :+85° min. Bottom : -85°min.
2-2. Luminance : 250(min), 300(Typ) (SDM-S74)
: 240(min), 300(Typ) (SDM-S94)
2-3. Contrast Ratio : 250(min), 450(Typ) (SDM-S74)
: 400(min), 700(Typ) (SDM-S94)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
• Type : Separate Sync,
SOG (Sync On Green)
Composite Sync, Digital
3-2. Video Input Signal
1) Type : R, G, B Analog
2) Voltage Level : 0~0.71 V
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.467 Vp-p
c) Color 15, 0 : 0.714 Vp-p
3) Input Impedance : 75 Ω
3-3. Operating Frequency
Horizontal : 28 ~ 80kHz (Digital: ~64kHz)
Vertical : 48 ~ 75Hz (Digital: ~60Hz)
4
. Max. Resolution
Analog : 1280 x 1024 / 75Hz
DVI Analog/ Digital : 1280 x 1024 / 60Hz
5. POWER SUPPLY
5-1. Power
: AC 100~240V, 50/60Hz , 1.0A
5-2. Power Consumption
6. ENVIRONMENT
6-1. Operating Temperature: 0°C~50°C
6-2. Relative Humidity : 10%~80%
6-3. MTBF : 50,000 Hours(Min)
7. DIMENSIONS (with TILT/SWIVEL)
(SDM-S74)
Width : 367mm (14.45'')
Depth : 215 mm (8.46'')
Height : 410 mm (16.14'')
(SDM-S94)
Width : 412mm (16.22'')
Depth : 234 mm (9.21'')
Height : 445 mm (17.51'')
8. WEIGHT (with TILT/SWIVEL)
(SDM-S74)
Net. Weight : 5.7kg (12.56 lbs)
Gross Weight : 8.3kg (18.30 lbs)
(SDM-S94)
Net. Weight : 7.1kg (15.65 lbs)
Gross Weight : 9.4kg (20.72 lbs)
CONTENTS
SPECIFICATIONS
- 2 -
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 4
TIMING CHART ....................................................... 4
OPERATING INSTRUCTIONS ................................ 6
WIRING DIAGRAM ................................................. 7
DISASSEMBLY ....................................................... 9
BLOCK DIAGRAM ................................................. 11
DESCRIPTION OF BLOCK DIAGRAM...................12
ADJUSTMENT ...................................................... 14
TROUBLESHOOTING GUIDE .............................. 15
EXPLODED VIEW...................................................19
REPLACEMENT PARTS LIST ...............................21
SCHEMATIC DIAGRAM......................................... 24
less then 1W
less then 0W
less then 1.2W less then 1.0W
240V/50Hz 100V/60Hz
MODE
POWER ON (NORMAL)
STAND-BY
SUSPEND
DPMS OFF
POWER S/W OFF
AC POWER OFF
H/V SYNC
ON/ON
ON/OFF
-
-
VIDEO
ACTIVE
OFF
-
-
POWER CONSUMPTION
less than 45 W (SDM-S74)
less than 50 W (SDM-S94)
LED COLOR
GREEN
AMBER
RED
OFF

- 3 -
Signal Connector Pin Assignment
Pin Signal (DVI-D)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
T. M. D. S. Data2-
T. M. D. S. Data2+
T. M. D. S. Data2/4 Shield
T. M. D. S. Data4-
T. M. D. S. Data4+
DDC Clock
DDC Data
Analog Vertical Sync.
T. M. D. S. Data1-
T. M. D. S. Data1+
T. M. D. S. Data1/3 Shield
T. M. D. S. Data3-
T. M. D. S. Data3+
+5V Power
Ground
(return for +5V,
H. Sync. and V. Sync.)
Pin Signal (DVI-D)
18
9
17 24
16 C1
C4
C3
C2
C5
16
17
18
19
20
21
22
23
24
Hot Plug Detect
T. M. D. S. Data0-
T. M. D. S. Data0+
T. M. D. S. Data0/5 Shield
T. M. D. S. Data5-
T. M. D. S. Data5+
T. M. D. S. Clock Shield
T. M. D. S. Clock+
T. M. D. S. Clock-
T. M. D. S. (Transition Minimized Differential Signaling)
• DVI-D Connector (Digital)

PRECAUTION
- 4 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
•There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
•Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
•Must mount the module using mounting holes arranged
in four corners.
•Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
•Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
•Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
•Make certain that treatment person’s body are
grounded through wrist band.
•Do not leave the module in high temperature and in
areas of high humidity for a long time.
•The module not be exposed to the direct sunlight.
•Avoid contact with water as it may a short circuit within
the module.
•If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
•If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
•Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
TIMING CHART
VIDEO
SYNC
B
D
CFE
A
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

- 5 -
Mode H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
720x400
70Hz
H–35.00 864 640 64 64 96 224
V–66.667Hz 525 480 3 3 39 45
640x480
60Hz
H–37.50 840 640 16 64 120 200
V–75.0Hz 500 480 1 3 16 20
640x480
65Hz
H–31.500 900 720 18 108 54 180
V + 70.156Hz 449 400 12 3 34 49
640x480
75Hz
H–35.162 896 720 34 40 102 176
V–59.901Hz 587 480 12 2 93 107 720x480
60Hz
H +- 35.156 1024 800 24 72 128 224
V + 56.250Hz 625 600 1 2 22 25 800x600
56Hz
H + 37.879 1056 800 40 128 88 256
V + 60.317Hz 628 600 1 4 23 28 800x600
60Hz
H + 48.077 1040 800 56 120 64 240
V + 72.188Hz 666 600 37 6 23 66 800x600
72Hz
H + 46.875 1056 800 16 80 160 256
V + 75.0Hz 625 600 1 3 21 25 800x600
75Hz
H–49.727 1152 832 32 64 224 320
V–74.553Hz 667 624 3 3 37 43
832x624
(MAC16”)
75Hz
H–48.363 1344 1024 24 136 160 320
V–60.004Hz 806 768 3 6 29 38 1024x768
60Hz
H–56.476 1328 1024 24 136 144 304
V–70.069Hz 806 768 3 6 29 38 1024x768
70Hz
H + 60.023 1312 1024 16 96 176 288
V + 75.029Hz 800 768 1 3 28 32 1024x768
75Hz
H–60.241 1328 1024 32 96 176 304
V–74.927Hz 804 768 3 3 30 36
1024x768
(MAC19)
75Hz
H + 67.500 1600 1152 64 128 256 448
V + 75.000Hz 900 864 1 3 32 36 1152x864
75Hz
H–68.681 1456 1152 32 128 144 304
V–75.062Hz 915 870 3 3 39 45
1152x870
(MAC21)
75Hz
H–61.795 1504 1152 30 128 194 352
V–65.950Hz 937 900 2 4 31 37 1152x900
66Hz
H–71.732 1472 1152 16 96 208 320
V–76.068Hz 943 900 2 8 33 43 1152x900
75Hz
H + 31.216 1480 1170 37 129 144 310
V + 50.026Hz 624 584 3 3 34 40 1170x584
50Hz
H + 60.000 1800 1280 96 112 312 520
V + 60.000Hz 1000 960 1 3 36 40 1280x960
60Hz
H + 63.981 1688 1280 48 112 248 408
V + 60.020Hz 1066 1024 1 3 38 42 1280x1024
60Hz
H + 79.976 1688 1280 16 144 248 408
V + 75.025Hz 1066 1024 1 3 38 42 1280x1024
75Hz
Sync
Polarity Frequency
Dot
Clock
Back Porch
(F)
Blanking time
(B)
Resolution
28.350
25.175
30.240
31.500
31.505
36.000
40.000
50.000
49.500
57.285
65.000
75.000
78.750
80.000
108.000
100.000
92.940
105.590
46.200
108.000
108.000
135.000
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H–31.469 800 640 16 96 48 160
V–59.940Hz 525 480 10 2 33 45
Sync Duration
(D)
Front Porch
(C)
Video Active Time
(A)
Total Period
(E)

- 6 -
OPERATING INSTRUCTIONS
REAR VIEW(SDM-S74) REAR VIEW(SDM-S94)
HD15(RGB) input
connector
Main Power Switch
AC IN connector
DVI-D(Digital) input
connector DVI-D(Digital) input
connector
Main Power Switch
AC IN
connector HD15(RGB) input
connector
1. (Power) switch and (power) indicator
This switch turns the monitor on when the power
indicator lights up in red. To turn the monitor off, press
this switch again.
If the power indicator does not light up, press the MAIN
POWER switch.
2. MENU Button
This button turns the menu screen on and off.
3. Buttons
These buttons are used to select the menu items and
make adjustments.
In addition, these buttons switch the Video input signal
between Input 1 and Input 2 when two computers are
connected to the monitor
4. OK Button
This button actives tge selected menu item and
adjustments made using the buttons(3).
5. ECO Button
This button is used to reduce the power consumption.
Front Control Panel
MENU
INPUT
OK
ECO
1
3
4
2
5

- 7 -
WIRING DIAGRAM
(SDM-S74)
J702
J705
J706
CN001
CN003
Connector Ass’y P/N:
6631T25005K
Connector Ass’y P/N:
6631T10003H
Connector Ass’y P/N:
6631T11016W

- 8 -
J702
J705
J706
WIRING DIAGRAM
(SDM-S94)
Connector Ass’y P/N:
6631T10003H
Connector Ass’y P/N:
6631T11016W
Connector Ass’y P/N:
6631T25005H

- 9 -
DISASSEMBLY(SDM-S74)
1) Please lift the central inside edge of Front bezel
upward with fingertip like picture, then latch will be
departed.
REAR CABINET REMOVEL.
2) Progress to left and lifts bezel furtively and extracts
latch.
3) Progress to right and extracts latch of bezel upper part
by same method.
4) Please pull upper side edge of Rear cabinet outside
with fingertip.
5) Please pull right side edge of Rear cabinet outside with
fingertip.
6) Please pull left side edge of Rear cabinet outside with
fingertip.

DISASSEMBLY(SDM-S94)
- 10 -
REAR CABINET REMOVEL.
2) Progress upward and lifts bezel furtively and extracts
latch.
3) Progress continuously and extracts latch of bezel upper
by same method. 4) Progress continuously and extracts latch of bezel left by same method.
5) Please pull the Rear cabinet both edge outside with
fingertips like picture, then Rear cabinet will be
departed.
6) If Rear cabinet be departed easily, please pull upside
edge of Rear cabinet outside.
1) Please lift the central inside edge of Front bezel
upward with fingertip like picture then latch will be
departed.

- 11 -
ADC
DVI(TMDS)
Inverter
Output
(4Lamp)
EEPROM
(EDID)
EEPROM
(System)
LVDS
Panel
Vcc
Regulator Regulator
KEY
DVI-D D-Sub X1
Filter
EEPROM*1
(EDID) MST9131B
3.3V
3.3V
2.5V
2.5V
5V
5V
MTV412PLCC
12V
DVI Rx
LAMP Connector
LIPS
OSD
Scaling Pre-Amp PLL
LVDS
Tx
+
BLOCK DIAGRAM

- 12 -
DESCRIPTION OF BLOCK DIAGRAM
1. Video Controller Part & Display Data Transmitter Part.
This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the
digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 135MHz.
This part consists of the Scaler, LVDS Tx, TMDS Rx, Reset IC.
The Scaler gets the video signals which were converted analog to digital, interpolates input to 1280 x 1024
resolution signal and outputs 8-bit R, G, B signal to transmitter.
Especially pre-amp / ADC / Video controller/ Transmitter are merged to one chip ‘MST9131A’by MST.
This part transmit digital signal from the Scaler to the receiver of module.
2. Power Part
This part consists of the one 3.3V and one 2.5 regulators to convert power which is provided 5V by LIPS Board.
In particular, 5V is provided for LCD Panel. There is also 12V which is for Audio power.
Also, 5V is converted 3.3V and 2.5V by regulator. Converted power is provided for IC in the main board.
3. System Controller (Microprocessor) Circuit
1) Microprocessor (U501) distinguishes polarity and frequency by calculating horizontal and vertical sync input from
signal source.
2) Microprocessor (U501) carries out power control by sending power-down trigger signal to each IC.
3) Microprocessor (U501) communicates with EEPROM (704), and MST9131A (U201) through IIC or 8 bit bus line.
It is enable to control and communicate each devices.
4) Microprocessor (U501) let User adjust screen by OSD function.

- 13 -
LIPS Board Block Diagram
EMI
COMPONENTS
LINE
100 ~ 240V
INPUT RECTIFIER
AND FILTER ENERGY TRANSFER OUTPUT RECTIFIER AND FILTER
12V
5V
GND
SIGNAL
COLLECTI
ON
PHOTO-
COUPLER
ISOLATION
PWM
CONTROL
CIRCUIT
HVDC 100KHz
PRIMARY SECONDARY
50 ~ 60Hz
Operation description_LIPS
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and also
the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor.

- 14 -
ADJUSTMENT
1. Procedures of how to go to service mode.
1) Enter the service mode of this unit by turning on the
power while pressing and holding the " " key
simultaneously.
2) Press "MENU" key----MAINTAIN.
3) Press "OK" key to enter the service menu.
4) Select the desired function.
5) Press the "MENU" key to exit OSD.
6) Turn off the power and then turn on it again. The
monitor then enters the normal mode.
To enter the service again, repeat the procedure
described above.
Note
W/B readjustment is required after the panel, board
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB reset
before W/B adjustment.
2. Setup
1) Prepare timing and pattern data for a signal
generator according to the Sony timing specifications.
2)
Connect a monitor video cable to the signal generator.
3) Put Color Analyzer(ex. CA-110) 50cm away from the
monitor, specify it vertically in the center of the
display, and adjust the focus to the optimum level
using an eyepiece.
4) Put the monitor and Color Analyzer(ex. CA-110) in a
light-shielded room.
5) Set up [SERVICE MODE] of the monitor.
3. Operation
Data is manually set to improve the productivity. The
brightness, contrast, and backlight are set to 50, 70
and 100 respectively. After that, the default data of the
color temperature to be adjusted is set.
4. Warm up time
Warm up for 30 minutes before performing any
adjustment.
5. Adjustment for White Balance
a. Display SMPTE at SXGA/60Hz(Input level 0.73mV).
b. Set up [SERVICE MODE].
c. Click "INITIAL EEPROM" and again setup Service
Mode.
d. Click "WHITE BALANCE" and then select “AUTO”.
6. 9300K color adjustment
a. Select "9300K" in "COLOR TEMP" and enter.
b. Use a 35%(89Gray) IRE white video field in the
primary mode.
c. Adjust "SUB CONTRAST " to secure the color
temperature.
d. Press "MENU" key to exit adjust mode.
7. 6500K color adjustment
a. Select "6500K" in "COLOR TEMP" and enter.
b. Repeat the adjustment procedure as steps b to d at
9300K.

- 15 -
NO PROBLEM
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK POWER
BOARD, AND FIND
OUT A SHORT POINT
AS OPENING
EACH POWER LINE
CHECK J705
VOLTAGE
PIN 5, 6, 8(5V)
PIN 1, 2(12V)?
NO
CHECK 5VS LINE
(OPEN CHECK)
CHECK
U501 PIN 8 Voltage
(5V) ?
NO
CHECK IIC LINE
CONNECTION
(U501, U502)
CHECK U201 VCC,
X501 XTAL CHECK
IS U201
PIN94 (3.3V), PIN85(2.5V)
VOLTAGE REPEATED
AS PULSE
SHAPE ?
NO
YES
YES NO PROBLEM
YES
CHECK KEY CONTROL
CONNECTOR ROUTINE

- 16 -
2. NO RASTER (OSD IS NOT DISPLAYED) –LIPS
CHECK MICOM INV
ON/OFF PORT.
CHECK
J705 PIN 9
5V?
NO
NO RASTER
(OSD IS NOT DISPLAYED)
CHECK LIPS
CHECK J705
PIN 5, 6, 8(5V)
PIN 1, 2(12V)?
NO
1. CONFIRM BRIGHTNESS
OSD CONTRL STATE.
2. CHECK MICOM DIM-ADJ
PORT
CHECK
J705 PIN 10
5V?
NO
LIPS
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL.
(CONTACT PROBE TO
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
NO
REPLACE CCFL LAMP
IN THE LCD MODULE
YES
YES
YES
YES

- 17 -
1. CHECK PIN11, 12
SOLDERING CONDITION
2. CHECK X501
3. TROUBLE IN U501
U201
POWER PIN 72,
82, 94(3.3V)
PIN 64, 85 (2.5V)?
NO CHECK U803
(2.5V REGULATOR),
CHECK U804
(3.3V REGULATOR)
U501
PIN11, 12
OSCILLATE AS
12MHZ?
CHECK CONNECTION LINE
FROM D-SUB TO U501
TROUBLE IN CABLE
OR LCD MODULE
YES
YES
YES
3. NO RASTER (OSD IS NOT DISPLAYED) –MST9131B
NO RASTER
(OSD IS NOT DISPLAYED)
U501
PIN41 IS 48KHz H-SYNC?
PIN42 IS 60Hz V-SYNC?
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
NO
NO

- 18 -
4. TROUBLE IN DPM
TROUBLE IN DPM
TROUBLE IN PC
CHECK PC
PC IS NOT GOING
INTO DPM OFF MODE
NO
TROUBLE IN
SIGNAL CABLE
NO
YES
YES
CHECK
R734, R741
(INPUT-1)SYNC.
R732, R755
(INPUT-2)SYNC.
CHECK
U501 PIN 24
(0V) ?

- 19 -
EXPLODED VIEW
1
5
2
2-1
6-1
3
7
8
9
11
13
14
15
12
4
16
10
6
9-1
17a
18

- 20 -
EXPLODED VIEW PARTS LIST
1
2
2-1
3
4
5
6
6-1
7
8
9
9-1
10
11
12
13
14
15
16
17
18
a
3091TKL077M CABINET ASSEMBLY, LOS74M SONY 3090TKL074A GRAY, TCO99 (SDM-S74)
3091TKL077N CABINET ASSEMBLY, LOS74M SONY 3090TKL074A GRAY-NT,TCO03 (SDM-S74)
3091TKL078L CABINET ASSEMBLY, LOS94M SONY 3090TKL075A GRAY, TCO99 (SDM-S94)
3091TKL078M CABINET ASSEMBLY, LOS94M SONY 3090TKL075A GRAY-NT,TCO03 (SDM-S94)
3091TKL078K CABINET ASSEMBLY, LOS94M SONY 3090TKL075A BLACK (SDM-S94)
6304FAU009A LCD(LIQUID CRYSTAL DISPLAY), M170EN05V4 AU TFT COLOR AUO V4(SDM-S74) TCO99
or 6304FAU005A
LCD(LIQUID CRYSTAL DISPLAY), M170EN05V1 AU TFT COLOR 17.0" SXGA LVDS SMM(SDM-S74)
6304FCI005B LCD(LIQUID CRYSTAL DISPLAY), M170E5-L05 CHIMEI TFT COLOR 300NITS 16MS TN SXGA(SDM-S74)
6304FAU012B LCD(LIQUID CRYSTAL DISPLAY), M170EN05-V6 AU TFT COLOR 300NITS,TN 16MS (SDM-S74) TCO03
6304FFT002C LCD(LIQUID CRYSTAL DISPLAY), FLC48SXC8V-11A FUJITSU TFT COLOR 300NITS LVDS MVA (SDM-S94)
6304FCI008A LCD(LIQUID CRYSTAL DISPLAY)M190E2-L01 CHIMEI TFT COLOR LVDS 8BIT (SDM-S94)
6304FAU013A
LCD(LIQUID CRYSTAL DISPLAY), M190EN02-V2 AU TFT COLOR 250 NITSLVDS SXGA MVA (SDM-S94)
3809TKL056H BACK COVER ASSEMBLY, LOS74M 3808TKL059A GRAY (SDM-S74)
3809TKL057H BACK COVER ASSEMBLY, LOS94M 3808TKL060A GRAY (SDM-S94)
3809TKL057G BACK COVER ASSEMBLY, LOS94M 3808TKL060A BLACK (SDM-S94)
3043TKK131V TILT SWIVEL ASSEMBLY, LOS74M, GRAY-NT(SDM-S74)
3043TKK131X TILT SWIVEL ASSEMBLY, LOS94M, GRAY-NT(SDM-S94)
3043TKK131W TILT SWIVEL ASSEMBLY, LOS94M, BLACK-NT (SDM-S94)
6871TST418F PWB(PCB) ASSEMBLY,SUB, LS74/94DM CONTROL TOTAL SONY CL-42
4950TKK487A METAL, FIX CONNECTOR-AU SIDE LS71K (SDM-S74)
4950TKK583A METAL, FIX CONNECTOR CMO 17 OX73(SDM-S74)
4950TKK547A METAL, FIX CABLE,LHS93K(SDM-S94) FUJITSU
4950TKK610A METAL, FIX CABLE CMO OS93(SDM-S94)
4950TKK772A METAL, FIX SIGNA OS94D(SDM-S94) AUO
4951TKS110K METAL ASSEMBLY, FRAME LOS74D_AUO NT (SDM-S74)
4951TKS110J METAL ASSEMBLY, FRAME LOS74D_CMO_L05 NT(SDM-S74)
4951TKS113H METAL ASSEMBLY, FRAME LOS94D_FUJITSU NT(SDM-S94)
4951TKS113J METAL ASSEMBLY, FRAME LOS94D_CMO NT(SDM-S94)
4951TKS113L METAL ASSEMBLY, FRAME LOS94D_AUO (SDM-S94)
3550TKK344H COVER, LOS53/73/93L PIECE POWER S/W GRAY, NT-LOCAL(SDM-S74)(SDM-S94)
3550TKK344G COVER, LOS53/73/93L PIECE POWER S/W BLACK, NT-LOCAL(SDM-S94)
6871TPT241N PWB(PCB) ASSEMBLY,POWER, OS73 POWER TOTAL SONY SPI FOR 17INCH AUO (SDM-S74)
6871TPT243F
PWB(PCB) ASSEMBLY,POWER, AI-0032C POWER TOTAL LIEN CHANG OS73L LIPS FOR NEW CMO (SDM-S74)
6871TPT249A PWB(PCB) ASSEMBLY,POWER, AI-0031(OX93L) POWER TOTAL LIEN CHANG 19"SONY STEP UP O/S FOR FUJITSU(SDM-S94)
6871TPT249B PWB(PCB) ASSEMBLY,POWER, AI-0031B(OS93L) POWER TOTAL LIEN CHANG 19" SONY OFFICE STANDARD FOR CMO(SDM-S94)
6871TPT249H PWB(PCB) ASSEMBLY,POWER, AI-0031H(OS93L) POWER TOTAL LIEN CHANG LIPS FOR AUO(SDM-S94)
6631T11016W CONNECTOR ASSEMBLY, 30P-30P H-H 200MM UL20276 AWG30 LOX73L/LOX93L(SDM-S74)(SDM-S94)
6631T11016M CONNECTOR ASSEMBLY, 30P H-H 200MM UL20276 AWG30 JAE LOCKING TYPE LOS93L(SDM-S94)AUO
6871TMT606B PWB(PCB) ASSEMBLY,MAIN, LS74DM SUEUGT SONY CL-42 TOTAL(SDM-S74)TCO99, AUO, EUROPE
6871TMT606D PWB(PCB) ASSEMBLY,MAIN, LS74DM SGEUGT SONY CL-42 TOTAL(SDM-S74) CMO, EUROPE
6871TMT606E PWB(PCB) ASSEMBLY,MAIN, LS74DM SGUSGT SONY CL-42 TOTAL(SDM-S74) CMO, U.S.A
6871TMT606A PWB(PCB) ASSEMBLY,MAIN, LS74DM SUUSGT SONY CL-42 TOTAL(SDM-S74) AUO, U.S.A
6871TMT606C PWB(PCB) ASSEMBLY,MAIN, LS74DM SUEUQT SONY CL-42 TOTAL(SDM-S74)TCO03, AUO
6871TMT562B
PWB(PCB) ASSEMBLY,MAIN, LS94DM SFEUGT SONY CL-42 TOTAL(SDM-S94) TCO99, EUROPE
6871TMT562E PWB(PCB) ASSEMBLY,MAIN, LS94DM SFEUQT SONY CL-42 FUJITSU TCO03 TOTAL(SDM-S94)
6871TMT562C PWB(PCB) ASSEMBLY,MAIN, LS94DM SGEUGT SONY CL-42 CMO TOTAL(SDM-S94)
6871TMT562D PWB(PCB) ASSEMBLY,MAIN, LS94DM SUEUGT SONY CL-42 AUO TOTAL(SDM-S94)
3313TL7043B MAIN TOTAL ASSEMBLY, LS74DM SONY CL-42 AUO (SDM-S74) TCO99, EUROPE
3313TL7043A MAIN TOTAL ASSEMBLY, LS74DM SONY CL-42 AUO UC/JP/CN(SDM-S74) TCO99, U.S.A
3313TL7043D MAIN TOTAL ASSEMBLY, LS74DM SONY CL-42 CMO AEP(SDM-S74) TCO99, EUROPE
3313TL7043E MAIN TOTAL ASSEMBLY, LS74DM SONY CL-42 CMO UC/JP/CN(SDM-S74) TCO99, U.S.A
3313TL7043C MAIN TOTAL ASSEMBLY, LS74DM SONY CL-42 AUO TCO03(SDM-S74)
3313TL9032B
MAIN TOTAL ASSEMBLY, LS94DM SONY CL-42 AEP GRAY(SDM-S94) TCO99, EUROPE, FUJITSU
3313TL9032E MAIN TOTAL ASSEMBLY, LS94DM SONY CL-42 FUJITSU TCO03(SDM-S94)
3313TL9032F MAIN TOTAL ASSEMBLY, LS94DM SONY CL-42 FUJITSU UC/JP/CN(SDM-S94) U.S.A
3313TL9032C MAIN TOTAL ASSEMBLY, LS94DM SONY CL-42 CMO(SDM-S94) TCO99, EUROPE
3313TL9032D MAIN TOTAL ASSEMBLY, LS94DM SONY CL-42 AUO(SDM-S94) TCO99, EUROPE
4951TKK138A METAL ASSEMBLY, REAR LOS73L(SDM-S74)
4950TKK604A METAL, REAR OS93(SDM-S94)
4950TKK611A METAL, BACK PLATE OS73 NT LOCAL
3550TKK388F COVER, LOS73L BACK DOOR GRAY, NT LOCAL (SDM-S74)
3550TKK392F COVER, LOS93L BACK DOOR GRAY-NT(SDM-S94)
3550TKK392E COVER, LOS93L BACK DOOR BLACK-NT(SGEUBT)(SDM-S94)
6850TD9004G CABLE,D-SUB, UL20276-9C(5.8MM) DT 1800MM BLACK(9930) SONY DM
4810TKK215B BRACKET, LOS53/93L HOLDER CONTROL PCB-NT
3846TKK062B MARK, PIECE BADGE SONY NO6.0(AL) 4-095-995-21 GREY
3846TKK062A MARK, PIECE BADGE SONY NO6.0(AL) 4-095-995-31 BLACK(SGEUBT)
332-113D SCREW,DRAWING, PVP+3*8(MSWR/FZMY)
Description
Part No.
Ref. No.