LG 50PC3D - - 50" Plasma TV User manual

PLASMA TV
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : PA-51D
MODEL : 50PC3D 50PC3D-UD
CANADA : http//biz.lgservice.com
USA : http//www.lgservice.com
: http//biz.lgservice.com
All manuals and user guides at all-guides.com
all-guides.com

- 2 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the same specified type.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
CANADA: LG Electronics Canada, Inc. 550 Matheson
Boulevard East Mississauga, Ontario L4Z 4G3
USA : LG Customer Interactive Center
P.O.Box 240007, 201 James Record Road Huntsville,
AL 35824
Digital TV Hotline [phone]
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
All manuals and user guides at all-guides.com

- 3 -
DESCRIPTION OF CONTROLS...........................................4
SPECIFICATIONS.................................................................8
ADJUSTMENT INSTRUCTIONS ..........................................9
BLOCK DIAGRAM...............................................................13
EXPLODED VIEW...............................................................16
EXPLODED VIEW PARTS LIST.........................................17
REPLACEMENT PARTS LIST............................................18
SCHEMATIC DIAGRAM..........................................................
PRINTED CIRCUIT BOARDS.................................................
TABLE OF CONTENTS
All manuals and user guides at all-guides.com

- 4 -
Controls
Controls
- This is a simplified representation of front panel.
- Here shown may be somewhat different from your TV.
CHCH
VVOLOL
ENTERENTER
MENUMENU
INPUTINPUT
CHANNEL (D, E)
Buttons
VOLUME (F,G)
Buttons
ENTER Button
MENU Button
INPUT Button
Remote Control Sensor
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates green when the set is switched on.
(Power) Button
DESCRIPTION OF CONTROLS
All manuals and user guides at all-guides.com

- 5 -
Connection Options
Connection Options
AV IN 2AV IN 2
L/L/MONO
MONO
RR
AUDIO
AUDIO
S-VIDEO
S-VIDEO
VIDEO
VIDEO
HDMI/DVI IN
HDMI/DVI IN
DIGITALAUDIO
DIGITALAUDIO
OUT
OUT
OOPTICAL
PTICAL
RS-232CIN
RS-232CIN
(CONTROL
(CONTROL
&& SERVICE)
SERVICE)
RGB(PC
RGB(PC
// DTV)
DTV)
RGBIN
RGBIN
AUDIO(RGB/DVI)
AUDIO(RGB/DVI)
VIDEO
VIDEO
AUDIO
AUDIO
MONO
(())
VIDEO
VIDEO
AUDIO
AUDIO
COMPONENTIN
COMPONENTIN
S-VIDEO
S-VIDEO
AV IN 1
AV IN 1
AV OUT
AV OUT
ANTENNA
ANTENNA
ININ
CABLE
CABLE
ININ AC IN
REMOTE
REMOTE
CONTROLIN
CONTROLIN
- Here shown may be somewhat different from your TV.
AUDIO Input
S-VIDEO Input
VIDEO Input
DIGITAL AUDIO OUT
OPTICAL
AV OUT
AV IN1
COMPONENT IN 1/2
HDMI/DVI IN
ANTENNA IN
CABLE IN
AUDIO(RGB/DVI)
RGB (PC/DTV)
AC IN
RS-232C INPUT
(CONTROL&SERVICE)
REMOTE CONTROL Port
DESCRIPTION OF CONTROLS
All manuals and user guides at all-guides.com

- 6 -
Remote Control Key Functions
Remote Control Key Functions
POWER
Turns your TV or any other programmed equipment on or
off, depending on mode.
VOL CH
POWER
123
456
78
0
9
MENU
MUTE FAV
DAY-
GUIDE
DAY+
RATIO
VCR
TV
DVD
ENTER
APM
ADJUST
SAP EZ SOUND
EZ PIC
FREEZE
FLASHBK
PAGE
PAGE
EXIT
TIMER
CC
INFO
AUDIO
CABLE
STB
MODE
TVINPUT INPUT
TV INPUT
Rotates the input mode between Antenna and Cable. In AV1-
2, Component 1-2, RGB-DTV (or RGB-PC), and HDMI/DVI
input sources, screen returns to the last TV channel.
MODE
Selects the remote operating mode: TV, DVD, VCR, AUDIO,
CABLE, or STB. Select a mode other than TV, for the remote
to operate an external device.
INPUT (Refer to p.14)
External input modes rotate in regular sequence: Antenna,
Cable, AV1-2, Component 1-2, RGB-DTV (or RGB-PC),
HDMI/DVI).
(AV1, AV2,Component 1-2 input sources are linked
automatically, Only if these are connected)
EXIT
Clears all on-screen displays and returns to TV viewing from
any menu.
TIMER
Lets you select the amount of time before your TV turns
itself off automatically.
CC
Select a closed caption: Off, CC1~4, Text1~4.
MENU
Brings up the main menu to the screen.
GUIDE
Shows program schedule.
RATIO
Changes the aspect ratio.
THUMBSTICK (Up/Down/Left/Right/ENTER)
Allows you to navigate the on-screen menus and adjust the
system settings to your preference.
INFO
When you watch the TV, information displays on top of the
screen. Not available in Component 1-2, RGB and HDMI/DVI
mode.
DESCRIPTION OF CONTROLS
All manuals and user guides at all-guides.com
all-guides.com

- 7 -
EZ PIC
Selects a factory preset picture mode depending on the view-
ing environment.
EZ SOUND
Selects the sound appropriate for the program's character.
SAP
Selects MTS sound: Mono, Stereo, and SAP in analog mode.
Change the audio language in DTV mode.
FREEZE
Freezes the currently-viewed picture.
ADJUST
Adjusts screen position, size, and phase in PC mode.
APM
Concurrently, compare with the Daylight, Normal, Night Time
and Custom on the screen.
FAV
Use to scroll the Favorite channels.
MUTE
Switches the sound on or off.
CHANNEL UP/DOWN
Selects available channels found with EZ scan and Manual scan.
PAGE UP/DOWN
Moves from one full set of screen information to the next one.
VOLUME UP/DOWN
Increases/decreases the sound level.
VOL CH
POWER
123
456
78
0
9
MENU
MUTE FAV
DAY-
GUIDE
DAY+
RATIO
VCR
TV
DVD
ENTER
APM
ADJUST
SAP EZ SOUND
EZ PIC
FREEZE
FLASHBK
PAGE
PAGE
EXIT
TIMER
CC
INFO
AUDIO
CABLE
STB
MODE
TVINPUT INPUT
— (DASH)
Used to enter a program number for multiple program chan-
nels such as 2-1, 2-2,etc.
NUMBER BUTTONS
FLASHBK
Returns to the last channel viewed.
VCR/DVD/DVHS/Camcorder BUTTONS
Control some video cassette recorders or DVD players
("RECORD" button is not available for DVD player).
DAY + / DAY-
Moves forward or backward in 24 hour increments.
DESCRIPTION OF CONTROLS
All manuals and user guides at all-guides.com

- 8 -
•The specifications shown above may be changed without prior notice for quality improvement.
MODEL
Television System
Program Coverage
External Antenna Impedance
Operating Temperature Range
Operating Humidity Range
Resolution
42PC3D/3DV-UD 50PC3D-UD
NTSC-M, ATSC, 64 & 256 QAM
VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69
75 Ω
32 ~ 104°F (0 ~ 40°C)
Less than 80%
42PC3D-UD: 1024 x 768 (Dot)
42PC3DV-UD: 852 x 480 (Dot) 1366 x 768 (Dot)
SPECIFICATIONS
All manuals and user guides at all-guides.com

1. Application Object
These instructions are applied to all of the PDP TV, PA-51D.
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test equipment.
(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver be must kept 110V, 60Hz
when adjusting.
(5) The receiver must be operational for about 15 minutes
prior to the adjustments.
1) After receiving 100% white pattern, the receiver must be
operated prior to adjustment. (Or 8. White Pattern
condition in EZ - Adjust)
2) Enter into White Pattern
- Press POWER ON Key on the Service Remote
Control (S R/C)
- Enter the Ez - Adjust by pressing ADJ Key on the
Service Remote Control (S R/C).
- Select the 7. White Pattern using CH +/- Key and
press the Enter(Y) Key.
Display the 100% Full White Pattern.
[Set is activated HEAT-RUN without signal generator in
this mode.
If you turn on a still screen more than 20 minutes (Especially
Digital pattern(13 CH), Cross Hatch Pattern), an afterimage
may occur in the black level part of the screen.
3. EPLD Download
(1) Test Equipment: PC, Jig for download
(2) Connect the power of VSC B/D.
(3) Execute download program(iMPACK) of PC.
(4) After executing the hot key on the Programmer, click icon
(5) End after confirming
4. POWER PCB Assy Voltage
Adjustment (Va, Vs Voltage Adjustment)
4-1. Test Equipment :D.M.M 1EA
4-2. Connection Diagram for Measuring
Refer to <Fig. 2>.
4-3. Adjustment
(1) Va Adjustment
1) Connect + terminal of D.M.M to Va pin of P805 and
connect – terminal to GND pin of P805.
2) Adjust RV601 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805 and
connect – terminal to GND pin of P805.
2) Adjust RV401 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
- 9 -
ADJUSTMENT INSTRUCTIONS
PC VSC
B/D
<Fig. 1> Connection Diagram of EPLD Download
Each PCB Assy must be checked by Check JIG Set before
assembly. (Especially, be careful Power PCB Assy which can
cause Damage to the PDP Module.)
<Fig. 2> Connection Diagram of Power Adjustment for
Measuring (Power Board)
All manuals and user guides at all-guides.com

- 10 -
ADJUSTMENT INSTRUCTIONS
5. EDID(The Extended Display
Identification Data)/DDC
(Display Data Channel) Download
This is the function that enables “Plug and Play".
5-1. HDMI EDID Data Input
(1) Required Test Equipment
1) Jig for adjusting PC, DDC. (PC serial to D-sub.
Connection equipment)
2) S/W for writing DDC(EDID data write & read)
3) D-Sub cable
4) Jig for HDMI Cable connection
(2) Preparation for Adjustments &
Setting of Device
1) Set devices as below and turn on the PC and JIG.
2) Open S/W for writing DDC (EDID data write & read).
(operated in DOS mode)
5-2. EDID DATA for PA-51D
:EDID for HDMI (DDC (Display Data Channel) Data)
EDID table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
______________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 0F 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
40 | 36 00 00 D0 52 00 00 18 00 00 00 FD 00 38 55 1F
50 | 3C 08 00 0A 20 20 20 20 20 20 00 00 00 FC 00 4C
60 | 47 20 54 56 0A 20 20 20 20 20 20 20 00 00 00 FC
70 | 00 50 44 50 0A 20 20 20 20 20 20 20 20 20 01 8F
80 | 02 03 13 F1 44 84 05 03 02 23 15 07 50 65 03 0C
90 | 00 10 00 01 1D 00 72 51 D0 1E 20 6E 28 55 00 C4
A0 | 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 25
B0 | 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0 2D 10 10
C0 | 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D
D0 | 10 10 3E 96 00 13 8E 21 00 00 18 00 00 00 00 00
E0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
F0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ED
:EDID DATA for RGB
EDID table =
0 1 2 3 4 5 6 7 8 9 A B C D E F
__________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 16 0F 01 03 68 6E 3E 96 0A 30 31 A8 55 40 AC 25
20 | 0D 47 48 AF CE 00 31 4F 45 4F 61 4F 01 01 01 01
30 | 01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
40 | 36 00 4C 6C 42 00 00 18 00 00 00 FD 00 38 4B 1E
50 | 3D 08 00 0A 20 20 20 20 20 20 00 00 00 FC 00 4C
60 | 47 20 54 56 0A 20 20 20 20 20 20 20 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 16
6. MST9883A-Set Adjustment
6-1. Synopsis
MST9883A-Set adjustment to set the black level and the Gain
of optimum with an automatic movement from the analog =>
digital converter.
6-2. Test Equipment
Service R/C, MSPG925FA Pattern Generator
(720P The Horizontal 100% Color Bar Pattern output will be
possible and the output level will accurately have to be
revised with 0.7±0.1Vp-p)
PDP TV SET
(or Digital Board)
<Fig. 3>
<Fig. 4> Adjustment Mode
<Fig. 5> Adjustment Pattern: HOzTV31Bar Pattern
(720P/60Hz: Format No. 217)
(480i/60Hz: Format No. 209)
All manuals and user guides at all-guides.com

- 11 -
ADJUSTMENT INSTRUCTIONS
6-3. Adjustment
(1) Select Component as the input with 100% Horizontal
Color Bar Pattern(HozTV31Bar) in 720p Mode and select
‘Normal’ on screen.
(2) After receiving signal for at least 1 second, press the ADJ
Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘1. MST9883A-720p Set’.
Pressing the Enter Key to adjust with automatic movement.
(3) When the adjustment is over, 'MST9883A Component
Success’ is displayed. If the adjustment has errors,
'MST9883A Configuration Error’ is displayed.
(4) After the Component MST9883A adjustment is over,
convert the RGB-DTV Mode and display Pattern.
When the adjustment is over, 'MST9883A RGB_DTV
Success’ is displayed.
(5) Select Component as the input with 100% Horizontal Color
Bar Pattern(HozTV31Bar) in 480i Mode.
(6) After receiving signal for at least 1 second, press the ADJ
Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘3. MST9883A-480i Set’.
Pressing the Enter Key to adjust with automatic movement.
(7) When the adjustment is over, 'MST9883A Component
Success’ is displayed. If the adjustment has errors,
'MST9883A Configuration Error’ is displayed.
[MST9883 480i adjustment is apply the only Component Mode.
(8) Readjust after confirming the case Pattern or adjustment
condition where the adjustment had errors.
(9) After adjustment is complete, exit the adjustment mode by
pressing the ADJ KEY.
7. Adjustment of White Balance
7-1. Required Equipment
(1) Color analyzer (CA-100 or similar product)
(2) Automatic adjustor (with automatic adjustment hour
necessity and the RS-232C communication being possible)
(3) Pattern Generator(MSPG-925FA): DVI Output
7-2. Connection Diagram of Equipment
for Measuring (Automatic Adjustment)
[[RS-232C Command (Automatic Adjustment)
7-3. Adjustment of White Balance
O Operate the Zero-calibration of the CA-100, then attach
sensor to PDP module surface when you adjust.
O Manual adjustment is also possible by the following sequence.
(1) Enter ‘Ez - Adjust’ by pressing ADJ KEY on the Service
Remote Control.
(2) Select "8. WHITE PATTERN" using CH +/- Key and HEAT
RUN at least 30 minutes by pressing the ENTER Key.
(3) Receive the Window pattern signal from Digital Pattern
Generator. (AV Input: connect the ‘HDMI’)
(4) After attaching sensor to center of screen, select ‘5. White-
Balance’ of ‘Ez - Adjust’ by pressing the ADJ KEY on the
Service R/C. Then enter adjustment mode by pressing the
Right KEY (
G ) .
(5) Adjust the Hight Light using R Gain/G Gain(Cool).
Adjust the Hight Light using G Gain/B Gain(Medium).
Adjust the Hight Light using G Gain/B Gain(Warm).
(6) Adjust using Volume +/- KEY.
After adjustment is complete, exit the adjustment mode by
pressing the ADJ KEY.
High Level: 216gray
[Cool]
X; 0.278±0.002 Y; 0.279±0.002
Color temperature: 11000°K±1000°K
[Medium]
X; 0.287±0.003 Y; 0.289±0.003
Color temperature: 9300°K±1000°K
[Warm]
X; 0.315±0.002 Y; 0.316±0.002
Color temperature: 6500°K±1000°K
R Gain
G Gain
B Gain
R Cut
G Cut
B Cut
Jg
Jh
Ji
Cool
Ja
Jb
Jc
Med
RS-232C COMMAND CENTER(DEFAULT)
Jd
Je
Jf
00
00
00
ff
ff
ff
7f
7f
7f
Warm Min Max
b8
bd
c0
40
40
40
Cool
c0
b8
b1
40
40
40
Med
c0
96
54
40
40
40
Warm
All manuals and user guides at all-guides.com
all-guides.com

- 12 -
ADJUSTMENT INSTRUCTIONS
8. Video(uPD)-Set
8-1. Required Equipment
MSPG925FA Pattern Generator-connector with Video Input
8-2. MSG925FA Adjustment
(1) After select the model, input the #201(NTSC-M).
(2) Receive the 100% Color Bar Pattern.(Pattern #32)
(3) Select the Reverse button and select the signal as below
figure.
8-3. Adjustment
(1) After receive signal to Ant input, CVBS output of
MSPG925FA to Video and confirm the signal receiving.
(2) Enter the ‘EZ-ADJUST’ by pressing the ADJ Key on the
Service R/C.
(3) Select ‘3. Video(uPD)-Set’ and enter the adjustment mode
by pressing the right key(
G ).
(4) When enter the adjustment mode, displayed the TV 2CH
Screen automatic at picture and appear as below figure.
(5) When the automatic adjustment is over, 'RF Configuration
Success’ is displayed. If the adjustment has errors, 'Video
Configuration Error’ is displayed.
(6) After the RF signal automatic adjustment is over, convert
the Video Mode as below figure and adjust with automatic
movement the Video Mode.
When the automatic adjustment is over, 'Video
Configuration Success’ is displayed. If the adjustment has
errors, 'Video Configuration Error’ is displayed.
All manuals and user guides at all-guides.com

- 13 -
BLOCK DIAGRAM
– –
–
–
–
All manuals and user guides at all-guides.com

- 14 -
BLOCK DIAGRAM
All manuals and user guides at all-guides.com

- 15 -
BLOCK DIAGRAM
All manuals and user guides at all-guides.com

- 16 -
EXPLODED VIEW
300
121
560
120
570
305
303 302
301
304
200
580
201
202
203
204
240
501
520
530
502
400
430
431
250
205
206
208
101
207
600
602
601
All manuals and user guides at all-guides.com
all-guides.com

- 17 -
EXPLODED VIEW PARTS LIST
101 5900904001A FAN,C4230S12B2-LG DONGYANG DC CROSSFLOW 12V 60MM 1100RPM 3P 850MM CFF
120 6400WMCX04A SPEAKER,WOOFER G2060102 M 8OHM 15W 82DB OTHERS 100HZ 240*57MM
121 6400DTTX02B SPEAKER,TWEETER EN15D-6659 8OHM 15/20W 78DB OTHERS PC1 MODEL
200 6348Q-C049N PDP,50 1365*768 PDP50X30010.AKDDG
6348Q-C049F PDP,50 1365*768 PDP50X30010.DDDRB *CSKD
201 6871QCH059B PCB ASSEMBLY,DISPLAY CTRL ASSY 50 CTRL WITH AU CONNECTOR
202 6871QDH088A PCB ASSEMBLY,DISPLAY YDRV ASSY 50X3 YDRV TOP
203 6871QDH089A PCB ASSEMBLY,DISPLAY YDRV ASSY 50X3 YDRV BOTTOM
204 6871QLH049D PCB ASSEMBLY,DISPLAY XRLT ASSY 50 X3 FFC TCP AU
205 6871QXH030D PCB ASSEMBLY,DISPLAY XRCT ASSY 50 X3 FFC TCP AU
206 6871QRH057D PCB ASSEMBLY,DISPLAY XRRT ASSY 50 X3 FFC TCP AU
207 6871QYH039A PCB ASSEMBLY,DISPLAY YSUS ASSY FOR 50X3
208 6871QZH044A PCB ASSEMBLY,DISPLAY ZSUS ASSY FOR 50X3
240 4980900101A SUPPORTER ASSY,AL NON
4980900101C SUPPORTER ASSY,AL SKD
250 4980900102A SUPPORTER ASSY,AL VERTICAL L
4980900102C SUPPORTER ASSY,AL VERTICAL L SKD
300 30919E0005A CABINET ASSEMBLY,50PC2R-TA BRAND 3090V00922 NON
30919E0005B CABINET ASSEMBLY,50PC3D-UD.SUSULLJR BRAND CSKD
301 4980900103A SUPPORTER,FILTER AL 50PC1R-TA, TOP
4980900103B SUPPORTER,FILTER AL 50PC3D-UD.SUSULLJR
302 4980900104A SUPPORTER,FILTER AL 50PC1R-TA, BOTTOM
4980900104B SUPPORTER,FILTER AL 50PC3D-UD.SUSULLJR BOTTOM
303 4980900105A SUPPORTER,FILTER AL 50PC1R-TA , RIGHT
4980900105B SUPPORTER,FILTER AL 50PC3D-UD.SUSULLJR RIGHT
304 4980900106A SUPPORTER,FILTER AL 50PC1R-TA , LEFT
4980900106B SUPPORTER,FILTER AL 50PC3D-UD.SUSULLJR LEFT
305 5230V00025B FILTER(MECH), LG CHEMICAL GLASS FILTER (40%)
400 3809900102D BACK COVER ASSEMBLY,50PC3 2PHONE DIGITAL
3809900102F BACK COVER ASSEMBLY,50PC3D-UD.SUSULLJR NON SKD
430 3501900004E BOARD ASSEMBLY,STAND 50PC3D-UD PA52D
3501900004F BOARD ASSEMBLY,STAND 50PC3D-UD PA52D SKD
431 35509K0101E COVER,42/50PC3D-UD CABLE DARK TITAN
501 3301900089D PLATE ASSEMBLY,AV 3300V00615 VTCP-PRESS
502 3301900092J PLATE ASSEMBLY,DIGITAL COVER ASSY (PA52D)(50INCH)
520 68719MM062A PCB ASSEMBLY,MAIN PA51D 50PC3D-UD AUSLLAX
530 68719SMJ26A PCB ASSEMBLY,SUB PA51D 42PC3D-UD AUSLLAX TUNER B/D
560 68719SM157A PCB ASSEMBLY,SUB PA51D 50PC3D-UD AUSLLAX CONTROL KEY
68719SM157B PCB ASSEMBLY,SUB PA51D 50PC3D-UD SUSLLJR CONTROL KEY SKD
570 68719SMJ11A PCB ASSEMBLY,SUB PA51D 50PC3D-UD AUSLLAX PREAMP+LED
68719SMJ11B PCB ASSEMBLY,SUB PA51D 50PC3D-UD SUSLLJR PREAMP+LED SKD
580 6709900020A POWER SUPPLY ASSEMBLY,50INCH UNIFAICATION PSU PDP LGIT PA61A 530W 50PB2DR
600 68719SM156A PCB ASSEMBLY,SUB PA51D 50PC3D-UD AUSLLAX SIDE AV
601 4811900021A BRACKET ASSEMBLY,SIDE AV 42PC3D-UD PA51D NORTH AMERICA
602 48149V0003B SHIELD,SIDE AV 50PC1R
No. Part No. Description
All manuals and user guides at all-guides.com

- 18 -
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
IC507
IC600
IC602
IC603
IC700
IC701
IC702
IC703
IC704
IC800
IC801
IC802
IC803
IC804
IC805
IC900
IC902
IC903
IC906
Q100
Q1000
Q1001
Q1002
Q1003
Q1004
Q1005
Q1006
Q1008
Q101
Q101
Q101
Q102
Q102
Q102
Q103
Q104
Q105
Q106
Q107
Q107
Q108
Q109
Q110
Q1100
Q1101
Q111
0IPRP00668A
0IPRPS5005A
0IMMRAL014C
0IMCRSJ001A
0IMCRFA013A
0ICB533100A
0ISTL00029A
0IPMGKE032A
0ICB841500B
0IMI623200B
0IPRPNS054A
0IMCRSJ001B
0IMCRSH001A
0IPMGKE032A
0IPMGKE032A
0IMCRSJ001A
0ICTMLG018B
0IMCRTH002A
0IPMGA0010A
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR387500AA
0TR102008AA
0TR830009BA
0TR102009AG
0TR387500AA
0TR387500AA
0TR102009AG
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR830009BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
IDT2309A-1DCG IDT 16P
SII9011CLU(PB FREE) 128P
AT24C02N-10SU-2.7 8P
SC1565IST-1.8 3P SOT223
74LCX244MTC 20P
CS5331A-KSR 8SOIC TP ADC -
MC33078DR2G 8P
KIA78R09F 5PIN DPAK R/TP 1A,9V
CS8415A-CZR 28P
M62320FP 16P
LM75CIMX-3 8P
SC1565IST-2.5TR 2.5V 1.5A 3P SOT-223
PQ05DZ1U SHARP 5
KIA78R09F 5PIN DPAK R/TP 1A,9V
KIA78R09F 5PIN DPAK R/TP 1A,9V
SC1565IST-1.8 3P SOT223
LGDP4411 IEP2 LG IC 208P
THC63LVD103 64P
AZ1117H-3.3 SOT-223 3P R/TP 3.3V
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
KRA102S SOT23 CHIP TR
BSS83
CHIP KRC102S KEC TP SOT-23
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP KRC102S KEC TP SOT-23
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
BSS83
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
LOCA. NO PART NO DESCRIPTION
IC100
IC100
IC1000
IC1001
IC1002
IC1003
IC1004
IC1005
IC1006
IC1007
IC1008
IC1009
IC101
IC101
IC102
IC103
IC103
IC104
IC107
IC108
IC110
IC1100
IC1101
IC111
IC200
IC200
IC201
IC201
IC202
IC202
IC203
IC300
IC301
IC302
IC303
IC304
IC305
IC306
IC400
IC401
IC500
IC501
IC502
IC503
IC504
IC505
0IMMRAL014C
0IMCRSS016A
0IMCRSH001A
0IMCRSH001A
0ILNR00015A
0IMCRTI028C
0IMCRMN027D
0IMCRSJ001A
0IMCRSJ001A
0IPMGA0010A
0IMCRFA010A
0IPMGA0010A
0IMCRSO025A
0IKE702900G
0IPH740800M
0ISO206900A
0IPH741400E
0ISTL00024A
0IMMRHY001L
0IMMRHY001L
0IKE704200J
0ICTMLG019A
0IPRP00538A
0IMCRAL006A
0IPRP00009A
0IMCRSH001A
0IMCRPH026B
0IMCRFA010A
0IMCRAL021A
0IMCRSH001A
0IMCRXL004A
0IPRPFA015B
0IPMGSG018C
0IPRPNE008A
0IMMR00080A
0IPRPFA016A
0IPMGA0010A
0IPRPM3002D
0ICTMLG009C
0IMCRSJ001A
0IMMR00141A
0IMMR00141A
0IMMR00141A
0IMMR00141A
0IMCRCY001A
0ICTMLG013A
AT24C02N-10SU-2.7 8P
S3C44BOX01-EDRO LQFP-160 TRAY CPU
PQ05DZ1U SHARP 5
PQ05DZ1U SHARP 5
NSP-2100A 64P DIGTAL AUDIO
TAS5122DCARG4 56P
MSP4440K 80P MULTI SOUND
SC1565IST-1.8 3P SOT223
SC1565IST-1.8 3P SOT223
AZ1117H-3.3 SOT-223 3P R/TP 3.3V
KA7809R 2P
AZ1117H-3.3 SOT-223 3P
CXA2181Q SONY 48P
KIA7029AF SOT-89 TP 2.9V
74F08D 14P
CXA2069Q QFP64 BK I2C BUS AV S/W
74HC14D 14SOP
MC14053BDR2G 16P
HY57V641620ETP-H 54P
HY57V641620ETP-H 54P
KIA7042AF SOT-89 TP 4.2V
LGDT3303 LG IC 100P
FSA1156P6X-NL 6P
AT24C16AN-10SU-2.7 8 EEPROM
ICL3232CBNZ 16P
PQ05DZ1U SHARP 5
PA9516APW 16P
KA7809R 2P
AT24C512W-10SU-2.7 8PIN
PQ05DZ1U SHARP 5
XC95288XL-10TQG144C 144P
FMS6400CS1X 8P
LD1086DT15TR 2P
UPD64011BGM-8ED-A 160
HY57V161610ETP-6 50PIN
FMS6407MTC20X-NL(PB-FREE) 20P
AZ1117H-3.3 SOT-223 3P R/TP 3.3V 1A
MST9883C-LF-110 80P
LGDT1102C HD2.3 SBGA-432P
SC1565IST-1.8 3P SOT223
HY57V641620ETP-6 54PIN
HY57V641620ETP-6 54PIN
HY57V641620ETP-6 54PIN
HY57V641620ETP-6 54PIN
CY2305SXC-1HT 8P
LGDT1901A LG IC 24P
IC
RUN DATE : 2006.2.17
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
TRANSISTOR
All manuals and user guides at all-guides.com

- 19 -
LOCA. NO PART NO DESCRIPTION
Q112
Q113
Q114
Q115
Q117
Q118
Q119
Q120
Q121
Q122
Q123
Q124
Q138
Q139
Q141
Q300
Q301
Q302
Q303
Q304
Q305
Q600
Q601
Q602
Q603
D100
D101
D106
D109
D1100
D1101
D115
D200
D201
D202
D203
D600
IC102
LD101
LED802
ZD1000
C100
C100
C1000
C1001
C1002
C1003
0TR387500AA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR102009AJ
0TR102009AJ
0TR102009AJ
0TR102009AG
0TR102009AG
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR102009AG
0DD184009AA
0DD181009AB
0DD184009AA
0DZRM00218A
0DL233309AC
0DL233309AC
0DD184009AA
0DRSE00038A
0DRSE00038A
0DL233309AC
0DL233309AC
0DD184009AA
0DD184009AA
0DL200000CA
0DL233309AC
0DZRM00248A
0CK104CK56A
0CE476WH6DC
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
KRC102S SOT23 50V 0.1A
KRC102S SOT23 50V 0.1A
KRC102S SOT23 50V 0.1A
CHIP KRC102S KEC TP SOT-23
CHIP KRC102S KEC TP SOT-23
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
BSS83
BSS83
BSS83
CHIP KRC102S KEC TP SOT-23
KDS184 TP KEC - 85V - 300MA
KDS181 TP KEC - 85V - 300MA
KDS184 TP KEC - 85V - 300MA
ZENERS,UDZS8.2B
LED,SAM2333
LED,SAM2333
KDS184 TP KEC - 85V - 300MA
SDC15 TVS SOT23 12.8V
SDC15 TVS SOT23 12.8V
LED,SAM2333
LED,SAM2333
KDS184 TP KEC - 85V - 300MA
KDS184 TP KEC - 85V - 300MA
LED,SAM5670(DL-2LRG) BK Y-GREEN -
LED,SAM2333
ZENERS,RLZ8.2B-TE11
0.1UF 1608 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
LOCA. NO PART NO DESCRIPTION
C1004
C1005
C1006
C1008
C1009
C101
C101
C101
C1010
C1011
C1012
C1013
C1014
C1015
C1016
C1017
C1018
C1019
C102
C102
C1022
C1023
C1024
C1025
C1026
C1027
C1028
C1029
C103
C103
C1030
C1031
C1032
C1033
C1035
C1038
C104
C1040
C1042
C1043
C1044
C1045
C1046
C1047
C1048
C1049
C105
C105
C1050
C1051
C1052
0CK104CK56A
0CK104CK56A
0CE476WH6DC
0CK102CK56A
0CC020CK01A
0CK104DK56A
0CK104CK56A
0CC101CK41A
0CC020CK01A
0CC101CK41A
0CK104CK56A
0CE476WH6DC
0CC560CK41A
0CC560CK41A
0CC560CK41A
0CK105DF64A
0CK104CK56A
0CK104CK56A
0CC220CK41A
0CC330CK41A
0CE476WH6DC
0CK104CK56A
0CK104CK56A
0CE476WH6DC
0CE335WK6D8
0CK104CK56A
0CK103CK56A
0CK102CK56A
0CC220CK41A
0CE4763F618
0CK104CK56A
0CK104CK56A
0CK474CH94A
0CK222CK51A
0CK474CH94A
0CK222CK51A
0CE4763F618
0CK104CK56A
0CK222CK51A
0CK222CK51A
0CK103CK56A
0CK222CK51A
0CC101CK41A
0CK222CK51A
0CK105DF64A
0CK104CK56A
0CC821CK41A
0CE4763F618
0CK222CK51A
0CK105DF64A
0CK222CK51A
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
1000PF 1608 50V 0.1 R/TP X7R
2PF 1608 50V 0.25 PF R/TP NP0
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
100PF 1608 50V 5% R/TP NP0
2PF 1608 50V 0.25 PF R/TP NP0
100PF 1608 50V 5% R/TP NP0
0.1UF 1608 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
56PF 1608 50V 5% R/TP NP0
56PF 1608 50V 5% R/TP NP0
56PF 1608 50V 5% R/TP NP0
1UF 2012 16V 20% F(Y5V) R/TP
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
22PF 1608 50V 5% R/TP NP0
33PF 1608 50V 5% R/TP NP0
47UF MVK 25V 20% SMD R/TP(SMD)
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
3.3UF MVK,RC 50V 20% SMD TAPPING
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
1000PF 1608 50V 0.1 R/TP X7R
22PF 1608 50V 5% R/TP NP0
47UF SRE,SE 16V 20% FL TP 5
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.47UF 1608 25V 80%,-20% R/TP F(Y5V)
2200PF 1608 50V 10% R/TP B(Y5P)
0.47UF 1608 25V 80%,-20% R/TP F(Y5V)
2200PF 1608 50V 10% R/TP B(Y5P)
47UF SRE,SE 16V 20% FL TP 5
0.1UF 1608 50V 10% R/TP X7R
2200PF 1608 50V 10% R/TP B(Y5P)
2200PF 1608 50V 10% R/TP B(Y5P)
0.01UF 1608 50V 10% R/TP X7R
2200PF 1608 50V 10% R/TP B(Y5P)
100PF 1608 50V 5% R/TP NP0
2200PF 1608 50V 10% R/TP B(Y5P)
1UF 2012 16V 20% F(Y5V) R/TP
0.1UF 1608 50V 10% R/TP X7R
820PF 1608 50V 5% R/TP NP0
47UF SRE,SE 16V 20% FL TP 5
2200PF 1608 50V 10% R/TP B(Y5P)
1UF 2012 16V 20% F(Y5V) R/TP
2200PF 1608 50V 10% R/TP B(Y5P)
REPLACEMENT PARTS LIST
DIODE
CAPACITOR
All manuals and user guides at all-guides.com

- 20 -
LOCA. NO PART NO DESCRIPTION
C1053
C1054
C1055
C1056
C1057
C1058
C106
C106
C1062
C1063
C1064
C1065
C1066
C1067
C1068
C1069
C107
C1070
C1072
C1073
C1074
C1075
C1076
C1077
C1078
C1079
C108
C1080
C1081
C1082
C1083
C1084
C1085
C1086
C1087
C1088
C1089
C109
C1090
C1095
C1097
C110
C1100
C1103
C1104
C1104
C1105
C1106
C1107
C1107
C1108
0CK104CK56A
0CK103CK56A
0CC471CK41A
0CE335WK6D8
0CK104CK56A
0CE107WF6DC
0CK104CK56A
0CE476WH6DC
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK103CK56A
0CK103CK56A
0CK104CK56A
0CK104CK56A
0CE108EJK18
0CK104CK56A
0CK333CK56A
0CK333CK56A
0CK333CK56A
0CK333CK56A
0CE108EJK18
0CE475WK6DC
0CE475WK6DC
0CK104DK56A
0CK103CK56A
0CK103CK56A
0CK103CK56A
0CK103CK56A
0CF4741L438
0CF4741L438
0CK104CK56A
0CK103CK56A
0CK103CK56A
0CK103CK56A
0CK104CK56A
0CK103CK56A
0CE107WF6DC
0CE476WH6DC
0CK104CK56A
0CK103CK56A
0CE476WH6DC
0CE105WK6DC
0CE476WH6DC
0CK103CK56A
0CK103CK56A
0CK104DK56A
0CE476WH6DC
0CK104DK56A
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
470PF 1608 50V 5% R/TP NP0
3.3UF MVK,RC 50V 20% SMD TAPPING
0.1UF 1608 50V 10% R/TP X7R
100UF MVK 16V 20% R/TP(SMD) SMD
0.1UF 1608 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
1000UF KMG,RD 35V 20%,-20% FL TP 5
0.1UF 1608 50V 10% R/TP X7R
33000PF 1608 50V 10% R/TP X7R
33000PF 1608 50V 10% R/TP X7R
33000PF 1608 50V 10% R/TP X7R
33000PF 1608 50V 10% R/TP X7R
1000UF KMG,RD 35V 20%,-20% FL TP 5
4.7UF MVK,RC 50V 20% SMD TAPPING
4.7UF MVK,RC 50V 20% SMD TAPPING
0.1UF 2012 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
100UF MVK 16V 20%
47UF MVK 25V 20%
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
1UF MVK 50V 20% R/TP(SMD) SMD
47UF MVK 25V 20% SMD R/TP(SMD)
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
0.1UF 2012 50V 10% R/TP X7R
LOCA. NO PART NO DESCRIPTION
C1108
C1109
C1109
C111
C1110
C1111
C1112
C1115
C1117
C1118
C112
C1121
C1121
C1122
C1123
C1123
C1124
C1125
C1126
C1126
C1127
C1127
C1128
C1128
C1129
C1129
C113
C1130
C1130
C1131
C1132
C1132
C1133
C1134
C1135
C1136
C1136
C1137
C1137
C1138
C1138
C1139
C1139
C114
C114
C1140
C1140
C1141
C1141
C1142
C1143
0CK103CK56A
0CK104DK56A
0CK104CK56A
0CK103CK56A
0CK104DK56A
0CE476WH6DC
0CK104CK56A
0CE225WK6DC
0CK103CK56A
0CK103CK56A
0CK103CK56A
0CK104CK56A
0CE105WK6DC
0CE476WH6DC
0CK104CK56A
0CE105WK6DC
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104DK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104CK56A
0CE225WK6DC
0CK103CK56A
0CK104DK56A
0CK104CK56A
0CK104CK56A
0CK104DK56A
0CE105WK6DC
0CE227SF6DC
0CK104CK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104DK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0.01UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
47UF MVK 25V 20% SMD R/TP(SMD)
0.1UF 1608 50V 10% R/TP X7R
2.2UF MVK,RC 50V 20% SMD TAPPING
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.01UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
1UF MVK 50V 20% R/TP(SMD) SMD
47UF MVK 25V 20% SMD R/TP(SMD)
0.1UF 1608 50V 10% R/TP X7R
1UF MVK 50V 20% R/TP(SMD) SMD
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
2.2UF MVK,RC 50V 20% SMD TAPPING
0.01UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
1UF MVK 50V 20% R/TP(SMD) SMD
220UF MVG 16V 20% R/TP(SMD) SMD
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 2012 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
0.1UF 1608 50V 10% R/TP X7R
REPLACEMENT PARTS LIST
All manuals and user guides at all-guides.com