LG LSW2010F User manual

OWNER'S MANUAL
Color Video Network Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LSW2010F
P/NO : MFL62591933

2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclo-
sure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the product.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equip-
ment may cause harmful interference unless the modifica-
tions are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interfer-
ence to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
A suitable conduit entries, knock-outs or glands shall•
be provided in the cable entries of this product in the
end user.

3
Caution: Danger of explosion if battery is incorrectly•
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Holes in metal, through which insulated wires pass,•
shall have smooth well rounded surfaces or shall be
provided with brushings.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environ-
ment this product may cause radio interference in which
case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabi-
net. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.

4
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from
the municipal waste stream via desig-
nated collection facilities appointed by
the government or the local authorities.
3. The correct disposal of your old appli-
ance will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you pur-
chased the product.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essen-
tial requirements and other relevant provisions
of Directive 2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327
AE Almere, The Netherlands
(Tel : [phone])

5
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the appa-
ratus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate nor-
mally, or has been dropped.
Important Safety Instructions

6
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the device is
liable to fail or to get cause of fire or electric shock.
Remove dust or dirt on the surface of the lens with a•
blower.
Use a dry soft cloth to clean the body. If it is very dirty,•
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
Avoid the use of volatile solvents such as thinners,•
alcohol, benzene and insecticides.
They may damage the surface finish and/or impair the
operation of the device.
Operating and storage location
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
Extremely hot or cold places (operating temperature•
from -10 °C to 50 °C, however, we recommend that the
unit be used within a temperature range from
0 °C to 45 °C)
Damp or dust place•
Places exposed to rain•
Places subject to strong vibration•
Close to generators of powerful electromagnetic radia-•
tion such as radio or TV transmitters.
Cautions for Safe Operation

7
Features................................................................. 8
Accessories........................................................................ 8
Part Names and Functions................................... 9
Connections ........................................................12
Precautions .....................................................................12
Connection Overview .................................................12
Connecting Display Device.......................................13
Connecting Network ...................................................13
Connecting Power Source.........................................14
Connecting Alarm Device..........................................15
Connecting Microphone and Speaker Device ...16
Mounting the Lens.......................................................16
Concerning Auto-Iris Lenses.....................................18
Flange-back Adjustment .........................................19
Mounting the camera .................................................20
Operation and settings ......................................21
Before using the system.............................................21
Recommended PC Requirements...........................21
Accessing the LG IP device ........................................22
LG Smart Web Viewer Overview..............................23
Conguring the LG IP camera ..................................26
OSD Menu Setup...........................................................51
Troubleshooting ................................................. 63
Open source software notice............................. 66
Specication .......................................................69
Contents

8
Features
The LG Color Video IP Camera is designed to use on an
Ethernet network and must be assigned an IP address to
make it accessible.
This manual contains instructions on how to install and
manage the LG Color Video IP Camera in your networking
environment.
Some knowledge of networking environments would be
beneficial to the reader.
Should you require any technical assistance, please contact
authorized service center.
Dual H.264 Stream for single Video Input•
Multi-Codec (H.264, MJPEG) Streaming•
PoE (Power over Ethernet) Support (802.3af)•
2 Power (DC 12 V, PoE) Support•
Audio Support (G.711, G.726 Full Duplex)•
Pre/Post Alarm Support•
Direct NAS Writing•
High resolution and high sensitivity with a 6 mm•
Super HAD II CCD.
Auto White Balance•
Day & Night function•
Accessories
Program CD•
User Manual•

9
ab c d ef
aLens mount cap
The lens mount of the camera is covered using a cap
to protect it. Remove the lens cap covering the lens.
bFlange-back adjustment ring
cCamera installation bracket
The bracket can be fixed at the top or bottom of the
camera.
dLens iris output connector (LENS)
This 4- pin connector is used to send the Iris control
signal and power supply to an auto-iris type lens.
eSetup menu control buttons
Use these buttons to set the menu options.
BUTTON Description
UP button
Used to move upper direction on the
menu screen. Use this button to select
an item or adjust the parameters.
DOWN button
Used to move lower direction on the
menu screen. Use this button to select
an item or adjust the parameters.
RIGHT button
Moves the cursor to the right. Used to
increment the value selected in the
menu. The parameter changes each
time this button is pressed.
Part Names and Functions

10
Part Names and Functions
LEFT button
Moves the cursor to the left. Used to
decrement the value selected in the
menu. The parameter changes each
time this button is pressed.
SET button
Executes selections and displays a sub-
menu for an item with the mark.
fALC Lens setting switch
VIDEO: When you attach an Auto Iris lens requir-•
ing the video control signal, please put this
switch in the VIDEO position.
DC: When you attach an Auto Iris lens requiring•
the DC control signal, please put this switch in
the DC position.
ghi
jk

11
gExternal device connectors
Power input terminal: Connects to a DC 12 V•
power supply using proper cables.
AUDIO OUT (Line Level Output): Connect to an•
active speaker with a built-in amplifier.
AUDIO IN (Line Level Input): Input for a mono•
microphone, or a line-in mono signal.
ALARM IN (Sensor input) Terminals:•
Provides physical interface for sensor.
ALARM OUT(R)/ALARM OUT (Relay output)•
Terminals:
Provides physical interface for Alarm/Relay.
hRESET button
Push the button more than 3 seconds, this would
restore the factory default settings.
iPower indicator
Lights when the camera is powered.
jVIDEO OUT
Supplies analog video signal (composite) to the con-
nected device.
kETHERNET/POE Port
Connects to a PC or a network via a hub with a 10
BASE-T/100 BASE-TX cable attached RJ-45 connector.
Note:
Power over Ethernet (PoE) is a technology that inte-
grates power into a standard LAN infrastructure. It
enables power to be provided to the network device,
such as a network camera, using the same cable as
that used for network connection. It eliminates the
need for power outlets at the device locations and
enables easier application of uninterruptible power
supplies (UPS).
Part Names and Functions

12
Precautions
Be sure to switch off the unit before installation and connection.•
The installation should be made by qualified service personnel or system installers.•
Do not expose the power and connection cables to moisture, which may cause damage to the unit.•
Connection Overview
PoE Device
(IEEE802.3af)
Connections

13
Connecting Display Device
Connect the video signal between the IP camera and the
monitor.
Connecting Network
You can control and monitor the system via network. With
the remote control (monitoring), you can change the sys-
tem configuration or monitor the image via network. After
the installation, check the network settings for the remote
control and monitoring work.
Connect the IP camera to your network using a standard
RJ-45 network cable as shown below.
PoE Device
(IEEE802.3af )
Router Broadband
Service
Broadband
Service
Broadband
Service
Broadband
Service
Router
PoE Device
(IEEE802.3af)
Connections

14
Connecting Power Source
Connect power, using one of the methods listed below:
To use the power adapter
Connect a DC 12 V power source to the power input
terminal as shown below.
1. Remove the insulation on the power cable as
illustrated.
2. Connect to the DC 12 V UL Listed, Class 2 Power
Supply only on the unit.
To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the unit.
You must use the “IEEE802.3af” standard PoE device.
PoE Device
(IEEE802.3af)
Note:
If the camera doesn't work properly after connect PoE
device, please check if the PoE device is supplying enough
power.
Connections

15
Connecting Alarm Device
Alarm terminals are used to connect the alarm (relay)
devices such as sensors, door switches, etc.
ALARM IN (Sensor Input )
Connect the sensor device to the sensor input
terminal.
Sensor
Device
ALARM OUT(R) / ALARM OUT (Relay Output)
Connect the alarm (relay) device to the relay output
terminal. Alarm signal is outputted at an event
occurrence.
Alarm (Relay)
Device
Note:
The Photo MOS Relay is rated for 100 mA at 20 V DC or
100 mA at 28 V AC.
Connections

16
Connecting Microphone and
Speaker Device
Optionally connect an active speaker and/or external
microphone with a built-in amplifier. Each Microphone and
Speaker should be connected with GND.
Note:
Keep the microphone away from the speaker to avoid
howling.
Mounting the Lens
1. Remove the lens mount cap from the camera.
2. Install the auto-iris lens.
2-1. CS mount type lens
Carefully align the lens mount with the camera
opening, then turn the lens slowly to install it.
2-2. C mount type lens
To allow for flange- back adjustment, install the
C-mount adaptor (option) on the lens mount,
then carefully align the lens mount with the cam-
era opening and turn the lens slowly to install it.
Connections

17
Connections
2-1
2-2
2-2
2-1
3. Connect the lens plug to the lens iris output connec-
tor (LENS) on the side of the camera.
When using lenses from other makers, the plug shape
may not correspond to the terminal on the camera.
In such a case, remove the original plug and using a
soldering iron, connect a lens iris plug according to
the diagram. (Refer to next page.)
lens iris output connector
Pin layout for the lens iris output connector.
No. DC type lenses VIDEO type lenses
1 Damping - Vcc (+9 V)
2 Damping + Not used
3 Drive + Video
4 Drive - Ground

18
Connections
Rewire the lens iris plug
1. Cut off the plug of the lens cable, cut off approxi-
mately 8 mm of the insulation, and then strip
approximately 2 mm of the ends of the cable
sheaths.
8mm
2mm
2. Solder the ends of the cable wires to the ends of
the pins, and then attach the cover of the lens iris
plug.
Concerning Auto-Iris Lenses
DC type auto-iris lens
A lens without driver circuit that operates only on a DC
power source. In general, this type of lens is referred to
as DC type coil lens. (Set the ALC Lens Setting Switch
to the DC position.)
CAUTION:
Depending on the type of lens used, the lens may not
perform properly.

19
Connections
VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video sig-
nal and DC power source. In general, this type of lens
is referred to as EE amplifier type lens. ALC and LEVEL
volume level controls are available on the lens for iris
adjustments. (Set the ALC Lens Setting Switch to the
VIDEO position.)
CAUTION:
Be cautions not to use Auto Iris Lens with over 35mA.
Flange-back Adjustment
The adjustment is required only when a lens without focus-
adjusting mechanism is mounted, or when a lens with
adjusting mechanism is mounted and focus that is more
accurate is needed.
1. Loosen the flange-
back fixing screws.
2. Use the flange-back
adjusting ring to
obtain a focused
point while watch-
ing the monitor
screen.

20
Connections
3. Tighten the flange-back fixing screws.
Note:
The object may be out of focus when using a source of
near-infrared light than using the visible light.
Mounting the camera
The mounting bracket can be secured on either the top or
bottom of the camera. Use the same set of screws to attach
the mounting bracket on the camera.
Note:
If using a camera mounting bracket, select a location that
is strong enough to bear the full weight of the camera and
the mounting bracket for long periods, and install the cam-
era and mounting bracket securely.