Eneo TSD-52F0013P0A User manual

EN
User Manual
1/3" HD Dome, Fixed, Day&Night,
1920x1080, Infrared, 1,34mm, 360°,
Indoor, 12VDC
TSD-52F0013P0A

2
Table of Contents
General safety instructions.............................................................................................. 3
1. Product Features .......................................................................................................... 5
2. The Overview ................................................................................................................ 6
3. Installation..................................................................................................................... 7
3.1 Connections................................................................................................................................7
3.2 Separate the main body of the camera and the base..................................................................7
4. Menu Operation............................................................................................................. 8
4.1 Main Menu.................................................................................................................................9
4.2 Video Type................................................................................................................................10
4.3 Video Setting ............................................................................................................................11
4.4 System.......................................................................................................................................13
4.4.1 Updating System Firmware............................................................................................................................13
5. Using a Web Brower................................................................................................... 15
5.1 Connecting to the Camera .......................................................................................................15
5.2 Browsing Images from the Camera..........................................................................................15
6. Specifications ............................................................................................................. 16

3
General safety instructions
Before switching on and operating the system, first read this safety advice and the operating
instructions.
Keep the operating instructions in a safe place for later use.
Installation, commissioning and maintenance of the system may only be carried out by authorised
individuals and in accordance with the installation instructions - ensuring that all applicable
standards and guidelines are followed.
Protect the devices from water penetration and humidity, since these can cause lasting damage.
Should moisture nevertheless enter the system, under no circumstance switch on the devices
under these conditions, rather send them for examination by an authorised specialist workshop.
The system must never be used outside of the technical specifications, since this can destroy it.
The device must be protected from excesses of heat, dust, humidity and vibration effects.
When separating the system from the voltage supply, only ever use the plug to pull out the cable.
Never pull directly on the cable itself.
Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or
damaged and that no humidity can penetrate into them.
In the event of a malfunction, please inform your supplier.
Maintenance and repairs may only be carried out by authorised specialist personnel.
The system must be isolated from the power supply before opening the housing.
The device may only be opened by qualified service personnel. Unauthorised access invalidates
any warranty claim.
Connection cables should always be exchanged through VIDEOR E. Hartig GmbH.
Use only original spare parts and accessories from VIDEOR E. Hartig GmbH.
The housing should only ever be cleaned using a mild domestic cleaning agent. Never use
solvents or petrol as these can permanently damage the surface.
During installation, it is essential to ensure that the seals provided are correctly installed and that
they are not displaced during installation. Damaged seals must not be installed.
The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by
sealing the cable outlets with silicone.
Wire end ferrules should be used when shortening the flexible connection cables.
The devices may only be operated in the temperature range indicated in the data sheet and within
the defined air humidity range.
Product-specific safety instructions:
Dome cameras
Do not attempt to remove the camera module from the dome.
The camera may never be pointed at the Sun with the aperture open (this will destroy the sensor).
All of the openings in the housing intended for installation must be closed and/or sealed.

4
It is unavoidable that during manufacture and to a certain extent during later use, humidity will be
present in the ambient air within the device's housing. In the event of large temperature
fluctuations, this humidity may condense inside the housing. To avoid this condensation inside the
very tightly sealed housing, the manufacturer has inserted silica gel bags in the housing.
It is however a physical given, that these silica gel bags will reach saturation after a certain amount
of time. They should therefore be replaced with new silica gel sachets.
The installer is responsible for the maintenance of the enclosure in accordance with the technical
data, e.g. through the use of all the accompanying seals and O-rings, through sealing of the cable
outlets with silicone and by laying the cables in such a way that no "water channel" results through
the cable.
During installation, it is essential to ensure that the seals provided are correctly installed and that
they are not displaced during installation. Damaged seals must not be installed.

5
1. Product Features
Full HD Image Quality and Details: A high-resolution megapixel sensor provides latency-free
1920x1080P Full HD resolution video to ensure that you won’t miss a thing.
Day/Night Surveillance: Integrated infrared LED illuminates darkness and provides a clear picture
at night for a dependable, 24-hour surveillance solution.
Direct fit to your existing HD-TVI DVR system: Just replacing your standard resolution analog
system with the HD-TVI compliant products through coaxial cable, you can seamlessly upgrade
your system to a HD analog system without additional cabling.
360°and assorted viewing modes.
Cost-effective Solution: Greater field of view at one time makes it a cost-effective replacement for
four separate 720P cameras.
OSD Menu: Functional cable (in-line joystick) with easier adjustment.

6
2. The Overview
1. Camera Lens.
2. Light Sensor: Detects light levels and adjusts IR-LEDs accordingly.
3. Micro SD Card Slot: Insert a micro SD card for firmware upgrading.
4. Power LED.

7
3. Installation
Please follow the instructions below to set up the system.
3.1 Connections
1. Connect the video output (①) from the camera to the DVR via BNC connector.
2. Connect the inlet (②) to an external power supply. Please connect with the 12V DC Power Supply.
3. The camera OSD menu is displayed by pressing the joystick in-line joystick (③)
3.2 Separate the main body of the camera and the base
To separate the main body of the camera and the base, please:
1. Rotate the main body 15 degrees in anticlockwise direction.
2. Then pick up the main body form the base.
➂In-line Joystick & Menu Button
➁DC Socket
➀HD-TVI Output

8
4. Menu Operation
This section shows you how to operate and manage the camera.
The operation interface of the different DVR may differ. Please refer to the actual operation interface.
The OSD Menu Structure:
VIEW TYPE
WALL 1O / 1P
CEILING 1P / 2P / 1O3R / 1O1R1P
/ 2R1P
VIDEO
SETTING
DAY & NIGHT AUTO / NIGHT / DAY
MIRROR H / V / HV / OFF
D-WDR OFF / ON
ADVANCE
BRIGHTNESS 0~8 (default: 4)
CONTRAST 0~8 (default: 4)
SHARPNESS 0~8 (default: 4)
SATURATION 0~8 (default: 4)
DENOISE 0~8 (default: 4)
WHITE BALANCE AUTO/ PUSHLOCK
EXPOSURE MAX GAIN 36 / 24/ 12 / 6 dB (default: 36)
BRIGHTNESS THRESHOLD 0~8 (default: 4)
HIGH LIGHT
COMPENSATION
OFF / ON: 1~8
(default: 7)
SYSTEM
FIRMWARE
VERSION UPDATE
LANGUAGE ENGLISH
VIDEO FORMAT NTSC / PAL
RESET

9
4.1 Main Menu
There are 2 ways to enter the camera’s OSD menu:
By the In-line Joystick of the Camera:
1. The OSD menu will be displayed by pressing the joystick of the camera.
2. Press right direction to enter the OSD menu. Navigate through the menus and change
parameters using the joystick via pressing the direction buttons.
3. To confirm (save and exit) your selection please press the center button again.
By the Coax Control of the DVR:
1. Our camera features the coax telemetry. It enables you to instantly see on-screen the
effects of any changes made.
2. Access the OSD menu via a DVR PTZ control panel.
3. Press the “” (right direction) button to enter the OSD menu. Navigate through the
menus and change parameters by pressing the direction buttons.
4. To confirm your selection please press the “” (right direction) button again.
The camera’s OSD main menu:
The Exit menu:
After changing any parameter, please remember to select the Exit item to enter the Exit menu.
Select the Save and Exit or Save item to change any configuration, and all the changes will only take affect
after saving.
Exit
Save and Exit →
Save →
Exit without Save →
Back →
Menu
1. Mounting type Ceiling
Viewing mode
ROI 1
View Window
Auto Pan OFF
Rotate 0
2. Video Setting →
3. System →
Exit →

10
4.2 Video Type
The video types are adjustable from both Wall and Ceiling mounting positions.
1. Viewing mode: Select the multiple viewing modes as you need.
1O: One original fisheye view.
2P: Two panoramic views.
1O3R: One original fisheye view and three regional views.
1O1R1P: One original fisheye view, one regional view and one panoramic view.
1P2R: One panoramic and two regional views
4R: Four regional views.
2. ROI: Select the desired section of the viewing mode from 1~3/ 4.
3. View Window: Select to see the outer () or inner () boundary of ROI.
4. Auto Pan: The auto-panning function allows user to see the horizontal move automatically between the
both ends of the ROI area.
5. Speed: Select the speed of the auto-panning function.
6. Rotate: Rotate the ROI area to see your desired direction of view.
NOTE:
When the product is installed on a wall or ceiling, the device should be firmly fixed.
Menu
1. Mounting type Ceiling
Viewing mode
ROI 1
View Window
Auto Pan OFF
Rotate 0
2. Video Setting →
3. System →
Exit →

11
4.3 Video Setting
Configure the details of the video settings setup for your camera.
1. Day/ Night: There are three parameters available for day/night mode configuration. It can be set as
Automatic, Day Mode or Night Mode.
(1) Automatic: The camera is capable of automatically switching from black and white mode (night)
and color mode (day) regarding to the lightening conditions. It is the default mode.
(2) Day (Color): You can switch it to Day mode in normal lighting conditions.
(3) Night (B/W): You can switch the IR cut filter into Black and White mode to increase then lens
sensitivity in low light conditions
2. Mirror:
(1) OFF: The default of mirror function is off.
(2) H: The video will flips 180 degrees in horizontal direction.
(3) V: The video will flips 180 degrees in vertical direction.
(4) HV: The video will flips 180 degrees both in horizontal and vertical direction.
3. D-WDR: The wide dynamic range (WDR) function helps the camera provide clear images even under
back
light circumstances. When there are both very bright and very dark areas simultaneously in the field
of view, WDR balances the brightness level of the whole image and provide clear images with details.
4. Advance: Configure the details of the advanced video settings for your camera.
(1) Brightness: An adjustable setting to compensate for backlit scenes.
(2) Contrast: Contrast is the degree of difference between the darker and lighter parts of the image.
Menu
1. Mounting type Ceiling
Viewing mode
ROI 1
View Window
Auto Pan OFF
Rotate 0
2. Video Setting →
3. System →
Exit →
Video Setting
1. Day/ Night Night Mode
2. Mirror OFF
3. D-WDR OFF
4. Advance →
Back →
Video Setting
1. Brightness 4
2. Contrast 4
3. Sharpness 4
4. Saturation 4
5. Denoise 4
6. White Balance AUTO
7. Exposure →
Back →
Exit →
Video Setting
1. Day/ Night Night Mode
2. Mirror OFF
3. D-WDR OFF
4. Advance →
Back →

12
(3) Sharpness: Set the value to automatically adjust the sharpness of the image to get a clear image.
The greater the value is, the stronger the effect will be.
(4) Saturation: Saturation indicates the brightness of the color. The higher the saturation, the brighter
the color is.
(5) Denoise: The Denoise (noise reduction) function is the process of removing noise from signals.
The greater the value is, the less the noise will be in the low illumination environment.
(6) White Balance: White balance is the white rendition function of the camera to adjust the color
temperature according to the environment automatically. White balance is the process of removing
unnatural shades of color, so that objects which appear white in reality are rendered white in the
images. Select your options from Auto and Push Lock.
Auto: This mode is typically used for outdoor applications or where variable lighting conditions
exist.
PushLock: Select PushLock o to calibrate the white balance for the current scene. This mode is
typically used for scenes with constant lighting conditions.
(7) Exposure:AE mode defines the priority of iris, shutter and gain while the camera adjusting the
brightness of the live view. You can change the mode on Exposure submenu.
I. Exposure Mode:
Auto: Automatic exposure mode.
Indoor: The optimum exposure setting is pre-programmed for the indoor environment.
Outdoor: The optimum exposure setting is pre-programmed for the outdoor environment.
II. Max Gain: The value of gain indicates the amplification degree of the original image signal.
III. Brightness Threshold: Set the brightness value of exposure.
iv. Highlight Compensation: Highlight compensation is a feature that came out of necessity due
to overexposure from strong light sources like headlights, torch light or spotlights. The default
value is off.
NOTE:
The highlight compensation and brightness threshold are connected. Before you configure the brightness
threshold, please enable the highlight compensation first.
Exposure
1. Exposure Mode Auto
2. Max Gain 24dB
3. Brightness Threshold 4
4. High Light Compensation OFF
Back →
Exit →

13
4.4 System
Displays all the information about your device.
1. Firmware Version and Update: Shows the firmware version here.
2. Language: The OSD display language is English.
3. Video Format: The video system is NTSC/ PAL (by region).
4. Reset: Enter the submenu to reload the factory default setting. Select Yes to continue.
4.4.1 Updating System Firmware
If the system firmware of the camera needs to be upgraded, please take the following steps to safely
process it.
NOTE:
Before carrying out the following procedures, please ensure the SD card is working and the file of the
system firmware is intact.
1. Copy the file of UPDATE.BIN to the SD card directory.
2. Insert the SD card into the camera.
3. Enter the Update submenu of the System page.
4. The Power LED will fast blinking red while this update process is running, please do not power off the
camera.
5. The Power LED will become solid red when this update process is finished, then remove the SD card
from the camera.
6. Verify the version of the system software.
NOTE:
You must perform Steps 1 on a PC.
Ensure you are using the correct UPDATE.BIN file in Step 1, otherwise the camera will not work
properly.
If the power of the camera is suddenly lost in step 4, please remove the SD card first and turn on the
SYSTEM
1. Firmware Version V1.04
Update →
2. Language English
3. Video Format NTSC
4. Reset →
Back →
Menu
1. Mounting type Ceiling
Viewing mode
ROI 1
View Window
Auto Pan OFF
Rotate 0
2. Video Setting →
3. System →
Exit →

14
camera next to test its operation. If the camera remains working normally, please go back to step 3;
otherwise, please inform your technical support.
Make sure that the SD card is inserted in a correct position in step 2, or the camera will suffer
permanent physical damage.
Do not interrupt the process when the unit is updating, or it will crash.

15
5. Using a Web Brower
This section provides instructions for remotely accessing the camera using a Web browser, such as the
Microsoft Internet Explorer.
NOTE:
Your DVR must be configured with a network connection to provide this access.
5.1 Connecting to the Camera
Start your Web browser (for example, the Microsoft Internet Explorer) and then follow these steps to
connect to the DVR:
1. Click on the URL entry box near the top of the Web browser window.
2. Enter the URL (address) of the DVR into the URL block, and press the Enter button to enter the
login page. Prepare the administrative User Name and Password respectively. Also, you can login
with any User name and password that has accessing permission for remote accessing.
3. Enter the user name. Then fill in the password. Both the user name and password must be correct.
4. Enter the home page of the DVR.
5. Select the fisheye camera then press the right button into the camera OSD menu.
5.2 Browsing Images from the Camera
After your PC was successfully connected to the DVR, the live images from the DVR will be displayed
on the home page.
The operation of Web browser is same as in the local DVR.

16
6. Specifications
Model TSD-52F0013P0A
HD-TVI Analog 360
°
Wide Angle View Camera
Camera Lens Fixed wide angle lens.
Image Sensor 3MP 1/3” progressive COMS sensor.
Image
Resolution 1920x1080.
Angle of View 360°
Frame Rate 25fps/ 30fps
Signal System PAL/ NTSC
Viewing Type Ceiling: 1P/ 2P/ 1O3R/ 1O1R1P/ 2R1P/ 4R.
Wall: 1O/1P.
Video Settings
Brightness/ Contrast/ Sharpness/ Saturation/
Denoise/ Mirror/ D-
WDR/ Exposure/ White
Balance
Indicator
Power LED Yes
Status LED Solid red: power on.
Blinking red: firmware upgrading.
Day & Night
IR LED Yes
IR Cut Filter Yes
Light Sensor Yes
Modes Auto/ Day/ Night
UTC Protocol Supports Pelco C protocol
General
Power Supply 12VDC, 1.5A
Power Consumption Max 3.2W
Operating Condition 0°C~40°C (32°F~104°F)
Coaxial Cable 3C/ 5C cable
Transmission Distance: Up to 500 meters.
Firmware Via micro SD card (for firmware upgrade only).
Language English
Dimension 77x33.5mm without bracket / 97x48.3mm with bracket
Package Weight 345 grams
Accessories
Quick Installation Guide.
Mounting hardware kit.
Mount.
**Design and specifications are subject to change without notice.

eneo® is a registered trademark of
VIDEOR E. Hartig GmbH
Exclusive distribution through special-
ised trade channels only.
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. [phone] / 888-0
Fax [phone] / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig
GmbH Version 04/2019