LG SJ5Y-S User manual

SIMPLE MANUAL
Wireless
Sound Bar
Please read this manual carefully before operating your set
and retain it for future reference.
To view the instructions of advanced features,
visit http://www.lg.com and then download Owner’s Manual.
Some of the content in this manual may differ from your unit.
MODEL
SJ5Y-S
Copyright © 2017 LG Electronics. All Rights Reserved
www.lg.com
*MFL69670147*
ENGLISH
WARNING:This product contains chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
FCC Compliance Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and the
receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation
of the device. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement : This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements :
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this device. This device cannot be co-located with any other
transmitter.
Responsible Party :
LG Electronics USA, Inc.
1000 Sylvan Ave
Englewood Cliffs, NJ 07632
Tel: [phone]
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
Printed in China
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 1-4 2017-05-11 �� 9:16:25

Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28
Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28

Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28

Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28

Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28

Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28

Front Panel
······································ Standby
······························ Selects Function
··························Adjusts Volume
Subwoofer Connection1
The buttons are located on the rear.
Rear Panel
DC IN ·················· Connect to the AC adapter
OPTICAL IN · · · · · · · · · · · Connect to an Optical device
PORTABLE IN ········ Connect to a Portable device
USB ·················· Connect to a USB device
HDMI OUT (TV ARC) ·············· Connect to a TV
HDMI IN ········· Connect to HDMI out on a device
Place the wireless subwoofer near the speaker and
follow steps below.
aConnect the power cord of wireless subwoofer
and sound bar to the outlet.
bTurn on the main unit. :
The sound bar and wireless subwoofer will be
automatically connected. The subwoofer's
green LED turns on.
Subwoofer Connection Manually
If the subwoofer does not make sound, try to
connect manually.
aPress Pairing button on the rear of the wireless
subwoofer.
yThe green LED on the rear of wireless
subwoofer blinks quickly.
bTurn on the main unit.
cPairing is completed.
yThe green LED on the rear of wireless
subwoofer turns on.
Keep the sound bar and the subwoofer away
from certain devices (ex. wireless router,
microwave oven, etc.) over 1m (3.28 ft) to
prevent wireless interference.
!P
3.28 ft
8: Turns down the volume at night.
AV SYNC: Synchronizes the audio and video.
AUTO VOL: Auomatically adjusts too loud or low output
volume level appropriately.
AUTO POWER: Automatically turns on by an input source.
Battery Replacement
Remote control
aConnect the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on
your TV setting menu.
TV
TV
TV Connection2
Optical Connection
HDMI(ARC) Connection
aConnect the sound bar to the TV using
HDMI cable.
bSet up [External Speaker (HDMI ARC)] on
your TV setting menu.
Connect with the Sound Bar and TV using
Optical ( ) or HDMI ARC ( ).
Additional Device Connection
aConnect to the external device as follows.
TV
OR
(Set-top Box,
Player etc.)
bSet the input source by pressing Fon the remote
control or unit repeatedly.
yHDMI connection is unavailable if your TV
does not support HDMI ARC.
yIf this unit is connected by OPTICAL and
ARC at the same time, the ARC signal has a
higher priority.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping
and handling) upon email request to opensource@lge.
com. This oer is valid for three (3) years from the date
on which you purchased the product.
Additional Information
Specication
Power
consumption Refer to the main label.
AC adapter
yModel :
DA-38A25
yManufacturer : Asian Power
Devices Inc.
yInput :
100 - 240 V ~ 50 - 60 Hz
1.2 A
yOutput : 25 V 01.52 A
Dimensions
(W x H x D)
Approx.
950 mm x 55 mm x 85 mm
(37.4 inches x 2.17 inches x 3.35
inches) With foot
Bus Power
Supply (USB) 5 V 0 500 mA
Amplier (Total
RMS Output
power) 320 W RMS
Design and specications are subject to change
without notice.
Rear Speakers Ready
Ready for surround sound with Rear Speaker
Kit sold separately. (SPJ4-S)
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 5-8 2017-05-11 �� 9:16:28

SIMPLE MANUAL
Wireless
Sound Bar
Please read this manual carefully before operating your set
and retain it for future reference.
To view the instructions of advanced features,
visit http://www.lg.com and then download Owner’s Manual.
Some of the content in this manual may differ from your unit.
MODEL
SJ5Y-S
Copyright © 2017 LG Electronics. All Rights Reserved
www.lg.com
*MFL69670147*
ENGLISH
WARNING:This product contains chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
FCC Compliance Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and the
receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation
of the device. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement : This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements :
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this device. This device cannot be co-located with any other
transmitter.
Responsible Party :
LG Electronics USA, Inc.
1000 Sylvan Ave
Englewood Cliffs, NJ 07632
Tel: [phone]
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
Printed in China
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 1-4 2017-05-11 �� 9:16:25

SIMPLE MANUAL
Wireless
Sound Bar
Please read this manual carefully before operating your set
and retain it for future reference.
To view the instructions of advanced features,
visit http://www.lg.com and then download Owner’s Manual.
Some of the content in this manual may differ from your unit.
MODEL
SJ5Y-S
Copyright © 2017 LG Electronics. All Rights Reserved
www.lg.com
*MFL69670147*
ENGLISH
WARNING:This product contains chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
FCC Compliance Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and the
receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation
of the device. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement : This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements :
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this device. This device cannot be co-located with any other
transmitter.
Responsible Party :
LG Electronics USA, Inc.
1000 Sylvan Ave
Englewood Cliffs, NJ 07632
Tel: [phone]
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
Printed in China
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 1-4 2017-05-11 �� 9:16:25

SIMPLE MANUAL
Wireless
Sound Bar
Please read this manual carefully before operating your set
and retain it for future reference.
To view the instructions of advanced features,
visit http://www.lg.com and then download Owner’s Manual.
Some of the content in this manual may differ from your unit.
MODEL
SJ5Y-S
Copyright © 2017 LG Electronics. All Rights Reserved
www.lg.com
*MFL69670147*
ENGLISH
WARNING:This product contains chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
FCC Compliance Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and the
receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation
of the device. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement : This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements :
High power radars are allocated as primary users of the
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage
this device. This device cannot be co-located with any other
transmitter.
Responsible Party :
LG Electronics USA, Inc.
1000 Sylvan Ave
Englewood Cliffs, NJ 07632
Tel: [phone]
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
Printed in China
SJ5Y-S.DUSALLB(K)_SIM_ENG_MFL69670147.indd 1-4 2017-05-11 �� 9:16:25