LG SK3B Specification sheet

Printed in China
FCC Compliance Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and
the receiver.
yConnect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired
operation. Any changes or modications in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with
minimum distance 20 cm (7.8 inches) between the
antenna and your body. Users must follow the specic
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference Requirements:
High power radars are allocated as primary users of the 5.25 to
5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can
cause interference with and/or damage this device. This device
cannot be co-located with any other transmitter.
Responsible Party:
LG Electronics USA, Inc.
1000 Sylvan Avenue
Englewood Cliffs, NJ 07632
Tel: [phone]
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
SIMPLE MANUAL
Wireless
Sound Bar
ENGLISH
Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions of advanced features, visit http://www.lg.com and then download Owner’s Manual.
Some of the content in this manual may differ from your unit.
MODELS
LAS485B SK3B
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
MFL69596812
LAS464B.DUSARLU_SIM_ENG_MFL69596812.indd 1-2 2018-07-27  1:37:51

Front Panel
Rear Panel
··································Standby /On
·······························Selects Function
··························Adjusts Volume
PORT. IN ············· Connect to a Portable device
OPTICAL IN ···········Connect to an Optical device
Subwoofer Connection1
Place the wireless subwoofer near the sound bar and
follow steps below.
aConnect the power cord of wireless
subwoofer to the outlet.
bTurn on the sound bar :
The sound bar and wireless subwoofer will
be automatically connected. The subwoofer's
yellow - green LED turns on.
Subwoofer Connection Manually
aReset the Subwoofer
If the yellow - green LED on the subwoofer
blinks rapidly, skip this step and go to b
yPress and hold PAIRING button for 5 seconds.
yThe LED lights up alternately in red and
yellow - green.
yUnplug the power cord. After the LED turns off
completely, plug in the power cord again.
When the reset is completed, the subwoofer's
yellow - green LED blinks rapidly.
bReset the sound bar
yAdjust volume to minimum until the red LED on
the sound bar lights up for a while.
yPress and hold (Mute) button on the remote
control for 3 seconds.
yThe red LED on the sound bar blinks rapidly.
yTurn the sound bar’s power off and on while the
subwoofer’s yellow - green LED blinks.
When the connection is completed, you can see the
yellow - green LED on the subwoofer.
Keep the sound bar and the subwoofer
away from the following (ex. wireless router,
microwave oven, etc.) over 1m (3.3 ft) to
prevent wireless interference.
!P
aConnect the the sound bar to the TV using
Optical cable.
bSet up [External Speaker (Optical)] on your TV
setting menu.
TV
TV Connection2 Remote control
Additional Device Connection
aConnect to the external device as follows.
TV
(Set-top
Box, Player
etc.)
bSet the input source by pressing Fon the
remote control or unit repeatedly. Additional Information
ASC/BASS BLAST/CINEMA:Selects sound effect.
NIGHT ON/OFF: Turns down the volume at night.
WOOFER LEVEL +/-:Adjusts the volume level of subwoofer.
AUTO POWER ON/OFF:Automatically turns on by an input
source.
Replacement of battery
Specication
Power
requirements Refer to the main label.
Power
consumption Refer to the main label.
Dimensions
(W x H x D)
Approx.
950 mm x 71 mm x 47 mm
(37.4 inch x 2.8 inch x 1.9 inch)
Amplier
(Total RMS
Output power)
300 W RMS
Design and specications are subject to change
without notice.
LAS464B.DUSARLU_SIM_ENG_MFL69596812.indd 3-4 2018-07-27  1:38:22