LG RJP-201M User manual

© Copyright 2010, LG Electronics U.S.A., Inc.
RJP-201M
Remote Jack Pack
Installation
& Setup Guide
Warranty

2
For Customer Support/Service, please call: 1-888-865-3026
www.lgsolutions.com
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK - - USE ONLY INDOORS
ATTENTION:
RISQUE DE CHOCS ÉLECTRIQUE - - POUR INSTALLATION À L¡¯INTÉRIEUR SEULEMENT
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
AVERTISSEMENT:
L’appareil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures et de plus
qu’aucun objet rempli de liquide tel que des vases ne doit être placé sur l’appareil.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way (except as noted herein) without written authoriza-
tion from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to
operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc., 2000 Millbrook Drive
Lincolnshire, IL 60069, USA •Phone: [phone].
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069
© Copyright 2010, LG Electronics U.S.A., Inc.

Table of Contents
3
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
Installation
Installation in Cabinet Backsplash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installer Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation Mixed Signal Breakout Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Connections to TV Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
End-User Operation
End-User Connections Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
End-User Multi-Media Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
End-User Connectable External Source Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
Troubleshooting
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RJP-201M Scaler RJP Supported Timing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

4
Overview
The Remote Jack Pack (RJP) contains circuitry to determine the pres-
ence of a signal at each input jack.
(Note: Audio In, Audio In L-R and Video In inputs detect the pres-
ence of the inserted plug, regardless if a signal is present or not.)
When a source is detected, its priority is compared to the priority of
other sources which may be present. If the newly-connected active
source is of higher priority than the existing source(s), the RJP
directs the TV display panel to that source.
Video and audio are monitored and switched independently.
Power is supplied to the RJP by the TV display panel via the control
signal cable.

Overview
5
CLEANING CAUTION:
Since the end-user jack panel is exposed, use extreme caution when
cleaning. Do not use liquid cleaners on the connection panel. Do
not allow liquids to be spilled, sprayed onto or otherwise come into
contact with the connection panel on either the end-user side or
the installer side. Clean with a slightly damp cloth.
7 AMPS MAXIMUM CURRENT FOR THE AC OUTLETS:
The maximum combined total current that is allowable to the four
AC power outlets is 7 Amps. These are protected by a circuit breaker
type re-settable fuse.
Introduction
Conveniently installed right in the room where guests will stay, the LG Remote
Jack Pack, (RJP) multi-media interface is available to end-users to connect audio,
video and computer devices to hear and view on the in-room TV display panel.
The RJP can be set up to interface with the TV display panel to show the image
and/or sound from a portable DVD/CD Player, Camcorder, MP-3 Player, Notebook
computer, or portable Video Game Player. Or, devices with digital video output
such as DVD players. A USB connection is available for future applications. If the
end-user does not connect any devices, then the in-room TV display panel will
remain on the source selected. When the end-user connects a device, the inter-
face switches the TV display panel to the new source. Users can recharge laptop
or cell phone batteries while watching TV.
The RJP interface is designed to be able to process audio from one source, and
video separately from a different source, if required. (The end-user can work on a
laptop computer while listening to music from an MP-3 player.) However, only
one audio and one video source can be heard/seen at the same time.
The end-user can simply plug the device’s power cord into one of the four conve-
nience AC power outlets provided on the RJP. Then plug in its Audio/Video
cable(s) to the RJP input jack(s) and turn the device on. The RJP completes the
connection between the newly-connected audio and/or video source and the TV
display panel. No end-user menus are involved, all connections are made directly
to the interface.
The RJP continually monitors its source inputs. When a signal is detected, (a
device is plugged into one of the RJP inputs) the interface sends a message to
the TV display panel to switch to the newly-connected source (if the new source
is of higher priority). The interface allows only the higher priority audio and
video to be heard and seen on the TV display panel. The control cable supplies
12 Volt DC power from the TV display panel to operate the interface.

6
Accessories
Ensure that the following accessories are included with your product.
Supplied Accessories
Mixed Signal Cable Assembly Installation & Setup Guide
6-Pin RJ-11 Phone Cable
(approx.6.0 feet)
5-Retainer Clips, L-Shaped 5-Machine Screws w/Serrated
Washers
Network Cable (8-Pin RJ-45)
w/Black Protective Sleeve
(approx.6.0 feet)

7
Mixed Signal Breakout Cable
Mixed Signal Breakout Cable
Item Description
No.
1. Audio Cable (Left/Right)
2. Digital Video Cable
3. Control Cable (8-pin RJ-45)
Gender Cable
Assembly
approx.
12.9
Feet
in
Length
Mixed Signal In
1.
Audio Cable
(L - R)
3.
Control
Cable
2.
Digital Video
Cable
Note: The actual appearance of the cable, cabinet, mounting hardware etc., may be different than shown in
these drawings.

8
Installation in Cabinet Backsplash
Installation Instructions
1. Remove the cabinet backsplash and insert the RJP into the cutout
opening.
2. Install the faour L-shaped mounting retainer clips, screws and
serrated washers provided to hold the RJP securely in place. Check
to assure that the RJP is securely mounted.
3. Make all connections to the RJP, please see the following page for
details.
4. After attaching cable hardware etc., reinstall backsplash on the
cabinet.
CAUTION: The cable wiring assembly should be handled
carefully to avoid damage, as it is fed through the opening
and attached to the RJP. The cable assembly needs to be
looped down into the area provided and then threaded
along the channel in the backside of the backsplash to the TV wiring
cutout in the cabinet. The AC power cord should be plugged into a
dedicated and appropriate AC wall power outlet.
The RJP-201M can only be installed in a vertical position
into the backsplash of the cabinet. Vertical mounting in the
backsplash is required so that if liquid is spilled on the desk
top, it will not be able to flow into the RJP. The RJP must
only be installed in the backsplash panel cutout opening. It will then
need to be secured with the four retainer clips, serrated washers and
machine screws provided. The cable wiring assembly and individual
cables will need to be connected to the RJP. All cables will need to
be threaded along the backside of the backsplash panel through the
TV wiring cutout to the TV and other in-room resources.
Note: The connector set that is closest to the mesh sleeving is for
hook up to the TV display panel.
Note: The actual appearance of the
cable assembly, cabinet, backsplash,
mounting hardware and cable
clamps etc., may be different than
shown in these drawings.
(4-Screws)

9
Installer Connections
The RJP-201M and the cables listed below are to be connected to both the TV display panel
and any entertainment resources available in the room.
CAUTION: Be sure power is turned off before attempting to connect the RJP-201M to the
TV display panel and in-room resources.
MIXED SIGNAL
OUT
NETWORK
OUT
PHONE
OUT
PHONE
OUT
NETWORK
OUT
MIXED SIGNAL
OUT
AC Power Cord
Connect to 120V 60 Hz AC
power outlet. Supplies
power to the four conve-
nience AC power outlets for
end-user. (Maximum com-
bined total current allowed
is 7 Amps.)
6-Pin RJ-11 Phone Cable
Connect to telephone line
wall jack panel.
Network Cable (8-Pin RJ-
45) w/Black Protective
Sleeve
Connect to LAN wall jack
panel.
Mixed Signal Cable
Mixed Signal Cable from Mixed
Signal Breakout Cable assembly
must connect to Mixed Signal Out
Connector.
Otherwise damage will occur.
Network Port (8-Pin RJ-45)
Connect to LAN wall jack, if available. Allows the end-user to access
the LAN (local area network) server of the institution.
Phone Port (6-Pin RJ-11)
Connect to telephone line wall jack. Allows the end-user, using a
computer modem, to connect to their ISP (Internet Service
Provider) to access the Internet through a local phone line.
AC Power Cord (Installed on RJP)
Connect to standard 120V 60Hz AC power outlet.
(Four 120 Volt 60 Hz AC power outlets are provided for
the end user.
However, 7 Amps. is the maximum combined current
allowed for the AC outlets.)

10
Installation Mixed Signal Breakout Cable
CAUTION: Be sure power is turned off before attempting to connect the RJP to the TV display
panel.
Note : The actual appearance of the cable, cabinet, hardware etc., may be different than shown in these
drawings.
1. Take off the two-sided tape that is
attached to the Mixed Signal Breakout
cable.
2. Attach the Mixed Signal Breakout cable
to TV display panel on the back.
3. Connect the Mixed Signal Breakout
cable to the TV display panel.

11
Connections to TV Display Panel
RS-232C IN
( SERVICE ONLY)
AUDIO IN
VIDEO
AUDIO
RGB IN (PC)
VIDEO AUDIO
L(MONO) R
2
1
L R
/DVI IN
COMPONENT IN
AV IN 1
UPDATE
RESET
(RGB/DVI)
REMOTE
CONTROL OUT
SPEAKER OUT
(8 )
RJP
After completing connections between the RJP and the TV display panel, be sure the installer menu items have
been updated to enable the RJP. Installer Menu item 040 Auto Camport needs to be set to 000 and 093 RJP
Available needs to be set to 005 or 006.
(See TV installation guide for complete instructions on new TV installations.) A brief description of each of the
available RJP connections is provided below.
Digital Video
Cable
6-Pin RJ-11
Phone Cable Network Cable
(8-Pin RJ-45)
w/Black
Protective
Sleeve
Power Cord
Audio Cable
(L-R)
Control
Cable
-TV/STB Installer Menu Item 093 RJP Available must have options 005 and 006 to be compatible.
Be sure to make all RJP connections beforesetting installer items.
Note:
-The actual appearance of the TV display panel
connections etc., may be different than shown
in this drawing.
-Installer Menu Item 093 RJP Available
(HDMI) for HDMI set to 005
(Digital video & Audio) for DVI set to 006
Network Port (8-Pin RJ-45)
Connect to LAN wall jack, if available. Allows the end-user to
access the LAN (local area network) server of the institution.
Phone Port (6-Pin RJ-11)
Connect to telephone line wall jack. Allows the end-user, using a
computer modem, to connect to their ISP (Internet Service
Provider) to access the Internet through a local phone line.
AC Power Cord (Installed on RJP)
Connect to standard 120V 60Hz AC power outlet.
(Four 120 Volt 60 Hz AC power outlets are provided for
the end user.
However, 7 Amps. is the maximum combined current
allowed for the AC outlets.)

12
End-User Connections Overview
®
P
R
E
S
T
O
S
R
E
10 AMP MAXIMUM CURRENT
S
E
T
PHONEINNETWORKIN
PC VIDEO IN
L-AUDIOIN-R
VIDEOIN
DIGITALVIDEO IN
AUDIOIN
CHARGE
SYNC
P
R
E
S
T
O
S
R
E
10AMPMAXIMUMCURRENT
S
E
T
PHONEINNETWORKIN
PCVIDEOIN
L-AUDIOIN-R
VIDEOIN
DIGITALVIDEOIN
AUDIOIN
CHARGE
SYNC
Today's
Report
Today's
Report
Typical
In-Room TV
Display Panel
End-User
Connection Panel
The end-user simply plugs a device such as a laptop computer with the appropriate cables, as shown in the
example, into the RJP connection panel. The Remote Jack Pack senses the new source connection and
switches the TV to the newly-connected source. The device’s sound and image are then presented on the in-
room TV display panel. The TV display panel adjusts automatically to the computer output format.
When the laptop is disconnected, the interface directs the TV to revert back to the previous source for video
and audio.
The end-user has several audio/video connection options available for connecting external devices. The
guest/user can connect a portable DVD Player, CD Player, Camcorder, MP-3 Player, Notebook Computer,
Portable Video Game Player, etc. For added convenience, four AC power outlets are also available on the front
of the interface to provide power for these external devices and/or recharge laptop or cell phone batteries.
(The maximum combined current allowed for the AC power outlets is 7 Amps.)
An end-user could connect and hear audio from one device and connect and view video from a different
device. The RJP offers two different stereo audio input jacks to accommodate various end-user devices.
However, only the higher priority audio source will be selected and heard. Similarly, multiple video inputs are
available, but only the higher priority video source will be selected and displayed.
(See page 12 input priorities.)

13
End-User Multi-Media Interface Connections
P
R
E
S
T
O
S
R
E
10 AMP MAXIMUM CURRENT
S
E
T
PHONE IN NETWORK IN
PC VIDEO IN
L-AUDIO IN-R
VIDEO IN
DIGITAL VIDEO IN
AUDIO IN
CHARGE
SYNC
Reset Switch
Circuit breaker for
AC power outlets.
AC Power Outlets
Four (4) convenience AC outlets
for end-user. (Total combined
current is 7 Amps maximum.)
Digital Video Input Port
Connection for digital video
sources. (portable DVD)
PC Video (RGB) Input Port
Connection for PC Video.
Video/Audio Input Jacks
Connection for composite
Video/Left-Right Audio
sources.
Phone In (RJ-11) Jack
Access to room’s phone line (PC
Modem).
Network In (RJ-45) Jack
Port for access to institution’s
local area network server, if
available.
3.5 mm Stereo
Audio Input Jack
Connection for MP-3
player or PC audio.
Note: Audio In, Audio In L-R and Video In inputs detect the presence of the inserted plug, regard-
less if a signal is present or not.
USB Charging Port
Connection for USB
device charging.
USB Sync Port
Connection for playing
multi-media file.
End-User Audio/Video Input Priorities
Note: The highest priority is listed first.
Audio Inputs/Sources
1st. 3.5 mm Stereo Audio Jack
2nd. Left - Right Audio Jacks
3rd. Digital Video Audio
4th. TV Display Panel Tuner Audio (Audio Default)
Video Inputs
1st. Digital Video
2nd. PC Video
3rd. S-Video
4th. Video Composite Jack
5th. TV Display Panel Tuner Video (Video Default)
Direct Connections to In-Room Resources
A. USB (if available)
B. LAN RJ-45
C. Phone RJ-11

14
•PC Laptop/Notebook Computers
•Portable Video Game Players
•Portable DVD/CD Players
•Camcorders
•Digital Cameras
•MP-3 Audio Players
The End-User Can Connect:
Examples of devices a guest/end-user
can connect are shown to the right.
There are four AC power outlets
available on the jack pack for added
convenience.
End-User Connectable External Source Devices
•USB Flash Drives
and other USB devices
(if available)

15
Specifications
Application
Makes available to the hotel’s guests, a multi-media interface to the in-room TV display panel and media
resources. Input jacks are provided for external portable devices such as DVD/CD Players, Laptop
Computers, Camcorders, etc.
Installer Connections
(RJP Back)
Network Out LAN Jack (8-Pin RJ-45)
Phone Out Phone Jack (6-Pin RJ-11)
(TV Display Back)
Mixed Signal Breakout • Digital Video Cable
Cable • Audio L-R
• Control Cable (8-pin RJ-45)
Dimensions
Height 4.08 Inches (103.6 mm)
Width 16.49 Inches (418.95 mm)
Depth 2.18 Inches (55.4 mm)
Weight (Approx.) 2.54 Pounds (1.15 kg)
End-User Device Inputs
AC Outlets x 4 AC 120V 60Hz (Maximum 7 Amps.
total combined current allowed for AC outlets)
Phone In Phone Jack (6-Pin RJ-11)
Network In LAN Jack (8-Pin RJ-45)
Audio In 3.5 mm Stereo Audio Jack
Audio In L-R Left - Right Audio Jacks
(Nom In: 250mV RMS @ 22K ohms)
Overload In: 1.6V RMS Max
Video In Composite Video Jack
1 Vpp, 75 ohms
PC Video In 15-pin RGB PC Monitor Connector
Digital Video In Digital Video Connector
USB In USB Connector (“A”-type female)

16
Specifications
Regulatory
UL, FCC Class B, Digital Video Device
Environmental Parameters
Operating Temperature 0° to 40° Degrees Celsius
(32° to 104° Degrees Fahrenheit)
Storage Temperature -20° to 85° Degrees Celsius
(-4° to 185° Degrees Fahrenheit)
Cooling Free Air Convection
Humidity 10% to 90% Non-condensing
Supplied Accessories List
(Cable Assembly) • Mixed Signal Cable Assembly (approx.12.9 ft)
(Separate Cables) •Phone Cable (6-Pin RJ-11)
•Network Cable (8-Pin RJ-45)
(Attached Cable) •AC Power Cord, 120V 60Hz
(Misc. Hardware) •5-Retainer Clips, L-Shaped (4-Required)
•5-Machine Screws w/Serrated Washers (4-Required)
Note: Design and specifications are subject to change without prior notice.

17
Problem Possible Cause(s) Check RJP, User Device and In-Room TV
No Power •Power not connected?
•Circuit breaker on RJP tripped?
(Unplug all accessory devices from RJP AC outlets, press RESET.)
No Audio •Have all audio connections been made?
•Audio output available?
•Volume level turned up?
•Sound muted?
•TV setup correct for RJP? (Installer menu item 040 is set to 000 and 093 set to 001.)
•Try another RJP.
•Priority level? (Disconnect other devices.)
No Video •Video output available?
•All video cables connected?
•TV setup correct for RJP? (Installer menu item 040 is set to 000 and 093 set to 001.)
•Priority level? (Disconnect other devices.)
Poor Video •Check connections. (Video pass-through no user action possible.)
USB
No USB •USB connected?
function •RJP USB port is a pass-through, no action possible.
Equipment Setup Analysis Notes
•RJP USB port is a pass-through connection, reserved for future applications.
•Make sure all connectors and connections are tight and secure on user device, RJP-201M and TV.
•Check to assure user device, RJP-201M and TV are all powered up and working properly and that the TV
Installer menu items are set correctly.
•Check to assure network interface to host is viable and working.
•Audio and Video can be from different sources. Default is TV tuner Audio and Video, if no other
audio/video source is connected.
•Audio source must be viable. The audio output from the customer’s device must be present when connected
to be heard at the TV.
•RJP AC circuit breaker maximum is 7 Amps. If 7 Amp current limit is exceeded, breaker will trip; unplug all
accessory devices from RJP AC outlets and press RESET.
Test Procedures
•Test and connect only one user device to determine if RJP is providing audio/video to TV.
•Test user device on another RJP (perhaps located in a different room) to determine if user device is com-
patible with RJP.
•On LCD or Plasma TVs, be sure Installer menu item 040 is set to 000 and 093 is set to 001 to enable RJP
mode.
Following are some possible solutions to problems:
Troubleshooting

18
Troubleshooting Flow Charts
No
Power
No Audio (or
not desired
Audio)
No Audio (or
not desired
Audio)
Power
Failure?
RJP
Has Circuit
Breaker
Tripped
?
RJP
Has Circuit
Breaker
Tripped
?
RJP
Is Video
connected
?
RJP
Are other
Video devices
connected
?
TV
Is TV
turned
On
?
User
Device
Is correct
Video output
selected
?
User
Device
Is Video
connected
?
RJP
Is Audio
connected
?
RJP
Are other
audio devices
connected
?
TV
Is TV
turned
On
?
TV
Are
Speakers
turned Off
?
TV
Is sound
Muted
or set too
low
?
User
Device
Is Audio
connected
?
User
Device
Audio
available &
turned up
?
RJP
Is power cord
connected
?
RJP
Has Circuit
Breaker
Tripped
?
TV
Is power cord
connected
?
TV
Is TV power
turned on
?
User
Device
Is power cord
connected
?
User
Device
Is device
turned On
?
Restore
Power Remove AC
load, press
RESET
Remove AC
load, press
RESET
Connect
Video
Cables
Disconnect
other
Video devices
Turn
TV On
Are
Installer menu
items set up?
Select
correct Video
output
PC
External
Port
Connect
Connect
Audio
Cables
Disconnect
other
Audio devices
Turn
TV On
Are
Installer menu
items set up?
Turn
Speakers
On
Press
Volume
Up
Connect
Turn
Volume
Up
Yes
Yes
No
No No
Yes
No
No
Yes
No
Yes
No
Yes
No
No
Yes
Yes
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
No
Yes
Yes
No
Connect
Power
Cord
Remove AC
load, press
RESET
Connect
Power
Cord
Turn
Power
On
Connect
Power
Cord
Turn
Power
On
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes

19
RJP-201M Scaler RJP Supported Timing List
1. Input
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
640x350@70
[email protected]
640x400@85
[email protected]
720x400@70
640x480@60
640x480@66
640x480@72
640x480@75
800x600@56
800x600@60
800x600@72
800x600@75
832x624@75
1024x768@60
1024x768@70
1024x768@75
1280x960@60
1280x960@75
1280x1024@60
1280x1024@75
1360x768@60
1360x768@75
1400x1050@60
1400x1050@75
1600x1200@60
1680x1050@60
1920x1080@60
480i
480p
576i
576p
720p50
720p60
1080i50
1080i60
1080p24
1080p25
1080p30
1080p50
1080p60
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
CVBS/HDMI(DVI)
RGB/HDMI(DVI)
CVBS/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
RGB/HDMI(DVI)
HDMI(DVI)
HDMI(DVI)
HDMI
HDMI
HDMI
RGB/HDMI(DVI)
RGB/HDMI(DVI)
Video Input Comments
Format
(Pixels x Lines)
2. Output
No
1
2
3
4
800x600@60
1360x768@60
1680x1050@60
1920x1080@60(RB)
HDMI(DVI)
HDMI(DVI)
HDMI(DVI)
HDMI(DVI)
Installer Menu only
Shipping Default
Future Using
Future Using
Video Output Comments
Format
(Pixels x Lines)

20
Quick Setup Guide
Installer RJP-201M Quick Setup Reference Guide
Following are the tasks associated
with installing and setting up an
RJP-201M System.
1. Install RJP-201M in cabinet.
2. Make all hard wire connections to
RJP-201M, TV and any other
inroom resources.
3. Plug all system components into
power sources.
4. Adjust TV installer menu items 040
and 093 to enable RJP capability.
(See TV installation guide for com-
plete instructions on new TV instal-
lations. The master TV setup
can be modified to include RJP
settings for multiple system instal-
lations.)
5. Test the system with user-type
devices to assure TV sound/picture
are as desired.
6. Provide user information in
room. (As applicable to your enter-
tainment system.)
Suggestions
•RJP-201M Tent Card. (Or equiv-
alent)
•RJP-201M Quick Reference
Guide. (Or equivalent)
RS-232C IN
( SERVICE ONLY)
AUDIOIN
VIDEO
AUDIO
RGB IN (PC)
VIDEO AUDIO
L(MONO) R
2
1
L R
/DVI IN
COMPONENT IN
AV IN 1
UPDATE
RESET
(RGB/DVI)
REMOTE
CONTROL OUT
SPEAKER OUT
(8 )
RJP
RJP-201MRemote JackPack(Seeother side)
Multi-Media Interface
QuickReferenceGuide
RJP-201MRemoteJackPack
Hotel GuestMulti-MediaInterface
•TheLGRemoteJackPackisprovidedtoconnectpersonalaudio,videoandPC
devicestohearandviewonthein-roomTV/displaypanel.
•Asshownontheleft,youcanconnectaportableDVD/CDPlayer,Camcorder,
MP-3Player,LaptopPC,VideoGamePlayerandotherentertainmentdevices--
charge yourcellphone,laptopetc.and watchTV.
CAUTION:Donotconnecthairdryers,clothingirons,coffeemakersorother
similarhigh-currentelectricdevicestothefourAC poweroutletsprovided.The
maximumloadforallfouroutletsis10Amps.
HowtoUsetheMulti-MediaInterface
•P
lugyourdevice’spowercordintooneofthefourACoutlets.
•C
onnectthedevice’saudio/videooutputtothemulti-mediainterface.
•Listentoaudiofromonedeviceandviewvideofromadifferent device. For
exampleyoucanlistentoyourMP-3playerwhileyouworkonyourlaptopPC.
Thein-roomTVplayssoundfromyourMP-3playeranddisplaysyourlaptop
PC’s imageontheTV’sscreen.Or,moretypicallyaudio/videofromthesame
device.(Seeotherside foravailableconnections.)
Note: All the multi-mediaconnectionoptions shownabovemaynot beavailable at this hotel.
Pleasecheck with thehotel to confirm what resources areavailable.
PC
Game
Machine
DVD
Player
Digital
Camera
MP3
Player
Camcorder
Flash
Drive
RESETSWITCH:The switchablecircuitbreakerisratedat10Amps.Ifthislimitis
exceeded,theRESETbuttonpopsupandAC poweristurnedoff.Ifthisoccurs,sim-
plypushintheredRESETbuttontoreinstateAC powerandresettheunit.
Standard
120 Volt
60Hz AC
Power
Outlet
Typical TV Display Panel
Installer Menu
Item Desc. Set
040 Auto Camport 000
093 RJP Available 001