LG VR6270 Series User manual

1.5 m1.5 m
2 m
Please, turn the
power switch ON.
Operation mode and cleaning
Installation of Home Station
Power ON and cleaning
1. Operation mode 2. Starting location
1. Install the Home Station after removing the
protection plastic wrap.
2. While in use (cleaning/recharging), always
keep the power cord plugged.
1. Turn the Main Power Switch on the rear-left
of main unit.
3. Starting and stopping the cleaning
2. Turn the power ON by pressing the 'Start/
Stop' button on main unit.
Be careful not to touch the main button on the unit, when
switching ON the power. Otherwise, the button may
possibly not work.
Pressing the button may turn ON the display.
Make sure to install it on a plane spot free of obstacles
within a 1.5 mdistance left-right and 2 mdistance
forward and not exposed to direct sunlight.
Keep the spare cords in order on the power cord hook.
• If the Charging Terminal has dusts on it, recharging could
fail. Clean regularly the Terminal with a dry mop.
• When putting the Robot Cleaner upside down, make sure to
put it on a soft cloth laid on the floor.
• Before turning over the main unit, remove the Dust Bin, first.
Otherwise, dusts may pour down from the Bin.
Tip
▒
A correct starting point
▒
A wrong starting point
Power cord not connected
to Home Station
Start near the wall Start with a hand blinding
the sensor lens
www.lg.com
Quick Guide
This guide briefly describes how to use the Cleaning Robot.
For more detail, please refer to the user manual
 Please read carefully this before installing and operating the product.
Cleaning Robot
VR6260 Ser.
VR6270 Ser.
[Main Power Switch
protection cap]
Chair
Corner
Carpet
Next to a Couch
Check if the LED glows red
in recharging.
Power cord connected
to Home Station
No obstacles within
a 30 cm radius
With the Robot Cleaner's power ON, pressing the 'Start/
Stop' button will start the cleaning, and another pressing
will stop it.
▒
ZigZag
: Swiftly clean a wide
space
▒
Cell by Cell
: Meticulously clean a
complex environment
▒
My Space
: Clean a desired,
particular spot
▒
Spot Cleaning
: Intensely clean an area
of a 1.5 mdiameter
1.5 m
Mi espacio
After the Robot Cleaner is turned on, press the 'Start'
button on the remote control. A melody will sound and
cleaning will begin.
Press the STOP button during the cleaning cycle to
'Stop' cleaning.

Voice message
Dust Bin/Sensor/Brush cleaning methods
Smart Diagnosis and Smart Operation
Recharging, threshold climbing and using the Mop Plate
1. Dust Bin 3. Brush (Side Brush)
2. Sensor lens
3. Threshold climbing height
1. "Please check that the dust bin and lter
are properly installed."
3. "The wheels are not touching the oor.
Please move HomBot onto at oor."
5. "Battery is low. Please move HomBot onto the
home station to charge."
4. "Please remove any foreign material on the
left/right wheel."
2. "Please remove any foreign material from
the brush on the bottom of the HomBot."
4. Mop Plate
1. Auto Charging
2. Manual Charging
Robot Cleaner nds the Home
Station to recharge itself, if cleaning
is complete or the battery is low.
In the latter case, above, the robot
nds the areas it could not cover
and continue to work on them.
The height of a threshold the robot can climb is
max. 15 mm; with the Mop Plate attached, 5 mm.
• With the Mop Plate attached, the height is limited
to such a level since it is required to prevent dusts
from contaminating the carpet, etc.
• Threshold climbing height also may vary depending on the shape of thresholds.
• Precautions with Learning mode
– 'Learning Mode' is available only when the robot
starts cleaning at Home Station.
– Robot Cleaner memorizes every aspect of the
environment it was put under from when it started
cleaning at Home Station to the moment it nished
its mission.
– Robot Cleaner learns the new conditions when the
location of Home Station has been changed.
– If learning mode is recognized, voice message will
say "The learning cleaning process is complete."
Tip
Tip
Empty the Bin after cleaning is nished, and clean the
Filter once a week with a brush.
Cut off and remove the hairs twined around the Brush
with the cleaning tool along the furrows.
Clean the lens regularly with a cleaning brush.
Brush
Side
brush
①
①
③
②
②
④
A warning message will be given if an alien material is
found on the Brush. Please remove any foreign material.
The battery requires charging.
If the Robot Cleaner cannot nd
the Home Station manually attach
the Robot Cleaner to the Home
Station for recharging.
[ Brush ]
[ Side Brush ]
1. Smart Diagnosis 2. Learning Mode
• In one of the following cases, Smart Diagnosis
may not work.
– If Robot Cleaner is detached from Home
Station
– If Battery is low
– If Dust Bin is not in place
– If Mop Plate is attached
• In 'Smart Diagnosis' mode, Robot Cleaner will
move about 50 cm. Clear any object in the way
within a 1 mradius from Home Station so that
its operation is not disturbed.
Tip
Tip
Robot Cleaner is capable of diagnosing itself through
Smart Diagnosis. For any irregularity found in the
Diagnosis, contact the local LG service center.
Robot Cleaner is capable of memorizing the cleaning
environment through its Learning mode for intelligent
cleaning operation.
Mop Plate attached to the robot may sometimes blind the sensor
to cause a malfunctioning (i.e., going backward or circling in a
same spot), so attach the Plate along the lines guided.
Separate with a
screwdriver
Removal of alien
materials
15 mm
①
③
②
④
Have the Robot Cleaner squared with the front of Home
Station.
Press the 'HOME' button on Remote Controller or main unit.
A warning message will be given if there is no Dust
Bin or Filter Cover available.
Please put the Dust Bin with Filter.