Liberty Digitalinx Series User manual

www.libav.com 800.530.8998
USER MANUAL
DL-HD70-H3 Owners Manual
Digitalinx Series HDBaseT 3.0 70m Extension Set
18G HDBaseT 3.0 Extender set extends uncompressed resolutions up to 4K60 4:4:4,
IR,RS232 & Power up to 40m or 70m

Rev 221712 OWNERS MANUAL DL-HD70-H3
PACKAGE CONTENTS
PRODUCT OVERVIEW
The Digitalinx DL-HD70-H3 HDBaseT 3.0 extender set transmits video, audio, IR, and RS232 over single
category 6a F/UTP or better twisted pair cable.The DL-HD70-H3 can transmit 4K resolutions up to 4K@60Hz,
4:4:4 up to 40m / 131’ and 4K30 or below up to 70m / 230’. The Digitalinx DL-HD70-H3 supports HDMI 2.0
and is HDCP 2.2/2.3 compliant and supports CEC pass through. The Digitalinx DL-HD70-H3 supports
multiple audio formats including PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio
and DTS:X . The Digitalinx DL-HD70-H3 supports any HDR format, including Dolby Vision and HDR10+..
The DL-HD70-H3 has an EDID Dipswitch to allow manual or auto EDID selection.
The DL-HD70-H3 is sold only as a set with a single power supply, and can be powered on either end.
• DL-HD70-H3 extender set
• (2) 3pin-3.81mm Phoenix Connectors (Male)
• (4) Mounting Ears with Mounting Screws
• 12V 2A Power Adapter with US, UK, AU AND EU Power Adapters
• (1) IR Emitter
• (1) IR Receiver (30kHz - 50kHz)
• (1) IR-AC Coupler Cable

3
OWNERS MANUAL DL-HD70-H3
TRANSMITTER PRODUCT BREAKDOWN
1. Power LED (Red) :When the red power LED is on the transmitter has power.
2. Status LED (Green) : When blinking the units are working properly.
3. Link LED (Green) : Link LED is on, the transmitter and receiver have a good connection.
When it's o the units are not connected.
4. HDCP LED : Solid light means HDMI signal with HDCP. Flashing light means HDMI signal
without HDCP. OFF - No Light means noHDMI signal
5. EDID DIP switch : See EDID section for settings.
1. Power In : Connects to power adapter. Either transmitter or receiver needs to be plugged
in to power.
2. IR in : Connects to the provided IR receiver.
3. IR out: Connects to the provided IR emitter.
4. HDBT out : Connects CAT cable to connect to the receiver.
5.HDMI in: Connects to an HDMI source.
6. RS-232 : Connects to a RS232 device Pass-through to receiver RS-232 port.

Rev 221712 OWNERS MANUAL DL-HD70-H3
RECEIVER PRODUCT BREAKDOWN
1. Power LED (Red) :When the red power LED is on the transmitter has power.
2. Status LED (Green) : When blinking the units are working properly.
3. Link LED (Green) : Link LED is on, the transmitter and receiver have a good connection.
When it's o the units are not connected.
4. HDCP LED : Solid light means HDMI signal with HDCP. Flashing light means HDMI signal
without HDCP. OFF - No Light means noHDMI signal
5. EDID DIP switch : See EDID section for settings.
1. Power In : Connect to power adapter. Either transmitter or receiver needs to be plugged
into power.
2. IR in : Connects to the provided IR receiver.
3. IR out: Connects to the provided IR emitter.
4. HDBT in : Connects CAT cable to connect to the transmitter.
5.HDMI out: Connects to an HDMI display or projector.
6. RS-232 : Connects to a RS232 device, Pass-through to transmitter RS-232 port.

5
OWNERS MANUAL DL-HD70-H3
CONFIGURATION SETTINGS
Below is an example of an extender set in a typical application.
APPLICATION DIAGRAM
DIP SWITCH on Receiver EDID MODE
1 is up and 2 is up Copy display's EDID (factory default)
1 is up and 2 is down 4K 30 4:4:4
1 is down and 2 is up 1080p60 4:4:4
1 is down and 2 is down 1200p60 4:4:4

Rev 221712 OWNERS MANUAL DL-HD70-H3
Cabling Requirements
HDBaseT Cabling
HDBaseT3.0 Specification is made using high quality Cat6a F/UTP cabling. For
maximum full capability performance, ensure Cat6a F/UTP or above is used.To ensure
proper performance of the DL-HD70-H3, it is recommended that you use solid core,
shielded Category 6aF/UTP or above cabling. Category 6 or 5e F/UTP may work but
may not support power over HDBaseT reliably and may only work over short distances.
For opmized HDBaseT performance use the following Liberty Wire and Cable branded
cabling;
Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH
Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON-plenum; 24-4P-L6ASH
When using shielded category cabling A LWAY S ...
....use shielded connectors
....properly ground the category cable
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6a
connection between send and receive
units.
RS232 Wiring
Connect the controller or device RX signal to
TX on the DL-HD70-H3 extender. Connect the
controller or device TX signal to Rx on the
DL-HD70-H3 extender.
RS232 Port
Connected RS232
Device Pins
TX G RX

7
OWNERS MANUAL DL-HD70-H3
TECHNICAL SPECIFICATIONS
Model DL-HD70-H3
Physical Parameter
Case Material Receiver: Industrial-grade metal chassis with metal brackets
Transmier: Industrial-grade metal chassis with metal brackets
Dimensions Transmier: 170mm [W] x 105mm [D] x 25mm [H]
Receiver: 170mm [W] x 105mm [D] x 25mm [H]
Weight Transmier: 265g
Receiver: 265g
Power Protecon ESD protecon with human body model — ±8kV (Air-gap discharge) & ±4kV
(Contact discharge)
Power Output DC 12V 2A
Power Input AC 100-240V 50/69Hz
Power Consumpon 14.28W (Max)
Operang Temperature 32- 113°F / 0- 45°C
HDMI Specicaons
HDMI 2.0b
HDCP 2.3/2.2/1.4
Video Bandwidth 18 Gbps
Video Resoluons 4096×2160@24/25/30/50/60Hz,3840×2160@24/25/
30/50/60Hz, 1920x1080p,[email protected]/24/25/29.97/
30/50/59.94/60Hz,1080i@50/59.94/60Hz, 720p@50/
59.94/60Hz, 576p, 576i, 480p, 480i
Color Space RGB, YCbCr 4:4:4 / 4:2:2. YUV 4:4:4
Color Depth 8/10/12-bit
Analog Audio Format LPCM 2.0
HDMI
Audio Formats
HDMI IN/OUT: Fully supports audio formats in HDMI 2.0 specicaon, including
PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio and DTS:X
Connecvity
Inputs Inputs: 1x HDMI
1x IR IN
1x DC 12V
Rx : 1xHDBT IN [RJ45, Female]
1x IR IN
1x DC 12V
Outputs Outputs: 1x HDBT OUT [RJ45, 8-pin female]
1x RS-232 Phoenix jack 3 pin (3.81mm)
1x IR OUT
Rx: 1xHDMI Type A-Female
1x IR OUT
Transmission
Max Distance (4K30)230ft / 70m over CAT6a 60m over Cat6
Max Distance (4K60 4:4:4)131 / 40m over CAT6a/7

Rev 221712 OWNERS MANUAL DL-HD70-H3
Thank you for your purchase.
For technical support please call our
toll-free number at 800-530-8998
or email us at [email protected]
www.libav.com 800-530-8998