Lifesaver i9040EU User manual

Manual 0940-7217-01 Rev.A
ATTENTION: Please take a few minutes to thoroughly read this
user guide which should be saved for future reference and passed
on to any subsequent owner.
Smoke Alarm
User Guide
i9040EU
• 9 Volt Battery Operated
Model: i9040EU
EN14604: 2005
LPCB Ref No. 904a/06
0832-CPD-1427
0940-7217-01_V1.qxd:_ 2013.7.1 4:17 PM Page 1

Smoke Alarm Procedure
NEVER IGNORE THE SOUND OF THE ALARM!
Smoke alarms are designed to minimize false alarms. Cigarette
smoke will not normally set off the alarm, unless the smoke is
blown directly into the alarm. Combustion particles from cook-
ing may set off the alarm if it is located too close to the cook-
ing area. Large quantities of combustion particles are generat-
ed from spills or when broiling. Using the fan on a range hood
which vents to the outside (non-recirculating type) will also
help remove these combustion particles from the kitchen.
If the alarm sounds, check for fires first. If a fire is discovered,
follow these steps. Become thoroughly familiar with these
steps and review with all family members:
• Alert small children in the home.
• Leave immediately by your escape plan. Every second
counts, so don’t waste time getting dressed or picking up
valuables.
• In leaving, don’t open any inside door without first feeling its
surface. If hot, or if you see smoke seeping through cracks,
don’t open that door! Instead, use your alternate exit. If the
inside of the door is cool, place your shoulder against it,
open it slightly and be ready to slam it shut if heat and
smoke rush in.
• If the air is smoky, stay close to the floor. Breathe shallowly
through a cloth, wet if possible.
• Once outside, go to your selected meeting place and make
sure everyone is there.
• Call the fire department from your neighbour’s home - not
from yours!
• Don’t return to your home until the fire officials say that it is
all right to do so.
What to do When the Alarm Sounds!
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 2

Welcome
i9040EU - 9 Volt Battery Operated Smoke Alarm with “HUSH”
Control to temporarily silence nuisance alarms.
Thank you for purchasing this smoke alarm. It is an important part
of your family’s home safety plan. You can trust this product to
provide the highest quality safety protection. We know you expect
nothing less when the lives of your family are at stake.
Important Warning Statements
IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLATION
AND KEEP THIS USER GUIDE NEAR THE ALARM FOR FUTURE REF-
ERENCE.
WARNING: BATTERY DOOR WILL NOT CLOSE AND/OR
ALARM WILL NOT ATTACH TO MOUNTING BRACKET UNLESS
BATTERY IS INSTALLED CORRECTLY.
REMOVAL OF BATTERY WILL RENDER THE SMOKE ALARM
INOPERATIVE.
WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER
RV OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE,
BEFORE EACH TRIP AND AT LEAST ONCE A WEEK DURING
USE.
CAUTION: DUE TO THE LOUDNESS OF THE ALARM (85
DECIBELS), ALWAYS STAND AN ARMS-LENGTH AWAY FROM
THE UNIT WHEN TESTING.
CAUTION:
BEFORE USING THE ALARM HUSH FEATURE,
IDENTIFY THE SOURCE OF THE SMOKE AND BE CERTAIN A SAFE
CONDITION EXISTS. NOTE: DENSE SMOKE WILL OVERRIDE THE
HUSH CONTROL FEATURE AND SOUND A CONTINUOUS ALARM.
SMOKE ALARMS ARE DEVICES THAT CAN PROVIDE EARLY
WARNING OF POSSIBLE FIRES AT A REASONABLE COST;
HOWEVER, ALARMS HAVE SENSING LIMITATIONS.
IONISATION SENSING ALARMS MAY DETECT INVISIBLE FIRE
PARTICLES (ASSOCIATED WITH FAST FLAMING FIRES) SOONER
THAN PHOTOELECTRIC ALARMS. PHOTOELECTRIC SENSING
ALARMS MAY DETECT VISIBLE FIRE PARTICLES (ASSOCIATED
WITH SLOW SMOLDERING FIRES) SOONER THAN IONISATION
ALARMS. HOME FIRES DEVELOP IN DIFFERENT WAYS AND
ARE OFTEN UNPREDICTABLE. FOR MAXIMUM PROTECTION,
KSE LIMITED RECOMMENDS THAT BOTH IONISATION AND
PHOTOELECTRIC ALARMS BE INSTALLED.
!
!
!
!
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 3

Contents of This User Guide
1. Recommended Locations for Smoke Alarms
2. Locations to avoid
3. Installation Instructions
4. Operation and testing
5. Nuisance Alarms
6. Maintenance
7. Limitations of Smoke Alarms
8. Good Safety Habits
9. Ionisation Information
10. Additional Information
11. Service and Warranty
This alarm detects products of combustion using the ionisation
technique. It contains 0.9 microcurie of Americium 241, a radioactive
material (see section 9). Do not try to repair the smoke alarm yourself.
Refer to the instructions in section 11 for service.
LOSS OF POWER TO THE ALARM WILL RENDER THIS ALARM
INOPERATIVE.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed
of with household waste.
Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
Product Specifications
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 4

• Locate the first alarm in the immediate
area of the sleeping rooms. Try to monitor
the exit path as the sleeping rooms are
usually farthest from the exit. If more than
one sleeping area exists, locate additional
alarms in each sleeping area (See figure 3).
• Locate additional alarms to monitor any
stairway as stairways act like chimneys for
smoke and heat.
• Locate at least one alarm on every floor
level.
• Locate an alarm in every sleeping room.
• Locate an alarm in every room where elec-
trical appliances are operated (i.e. portable
heaters or humidifiers).
• Locate an alarm in every room where
someone sleeps with the door closed. The
closed door may prevent an alarm not
located in that room from waking the
sleeper.
• Smoke, heat, and combustion products
rise to the ceiling and spread horizontally.
Mounting the smoke alarm on the ceiling
in the centre of the room places it closest
to all points in the room. Ceiling mount-
ing is preferred in ordinary residential con-
struction.
• For mobile home installation, select loca-
tions carefully to avoid thermal barriers
that may form at the ceiling. For more
details, see MOBILE HOME INSTALLATION
below.
• When mounting an alarm on the ceiling,
locate it at a minimum of 10 cm from the
side wall (see figure 1).
• When mounting the alarm on the wall,
use an inside wall with the top edge of
the alarm at a minimum of 10 cm and a
maximum of 30.5 cm below the ceiling
(see figure 1).
1. Recommended Locations for Smoke Alarms
FIGURE 1
ANYWHERE ALONG
10 cm
10 cm
FIGURE 3
FIGURE 2
ANYWHERE ALONG
THIS BOLD SURFACE
30.5 cm
FIGURE 4
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 5

1. Recommended Locations for Smoke Alarms
• Put smoke alarms at both ends of a hallway or large room if the
hallway or room is more than 9.1 m long. For large rooms, one
smoke alarm is recommended for every 47 square meters of floor
space.
• In homes that are not well insulated, extreme heat or cold can be
transferred from the outside to the inside through poorly insulated
walls and roof. This may create a thermal barrier which can prevent
the smoke from reaching an alarm mounted on the ceiling. If you are
not sure about the insulation in your home, or if you notice that the
outer walls and ceiling are either hot or cold, install the alarm on an
inside wall. In such homes, install the smoke alarm with the top edge
of the alarm at a minimum 10 cm and a maximum of 30.5 cm below
the ceiling (see figure 1).
• Install Smoke Alarms on sloped, peaked or cathedral ceilings at or
within 0.9m of the highest point (measured horizontally). Smoke
alarms in rooms with ceiling slopes greater than 0.3m in 2.4 m
horizontally shall be located on the high side of the room. A row of
detectors shall be spaced and located within 0.9m of the peak of the
ceiling measured horizontally (see figure 2).
• Install Smoke Alarms on tray-shaped ceilings (coffered ceilings) on the
highest portion of the ceiling or on the sloped portion of the ceiling
within 30.5cm) vertically down from the highest point (see figure 4).
Mobile Home Installation
Modern mobile homes have been designed and built to be energy effi-
cient. Install smoke alarms as recommended above (refer to RECOM-
MENDED LOCATIONS and Figures 1 and 2). In older mobile homes that
are not well insulated compared to present standards, extreme heat or
cold can be transferred from the outside to the inside through poorly
insulated walls and roof. This may create a thermal barrier which can
prevent the smoke from reaching an alarm mounted on the ceiling. In
such units, install the smoke alarm on an inside wall with the top edge
of the alarm at a minimum of 10cm and a maximum of 30.5cm below
the ceiling (see figure 1).
If you are not sure about the insulation in your mobile home, or if you
notice that the outer walls and ceiling are either hot or cold, install the
alarm on an inside wall. For minimum protection, install at least one
alarm close to the sleeping rooms. For additional protection, see SINGLE
FLOOR PLAN in figure 2.
WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER RV
OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, BEFORE
EACH TRIP AND AT LEAST ONCE A WEEK DURING USE.
!
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 6

• In the garage. Products of combustion are present when you start
your automobile.
• Less than 10cm from the peak of an “A” frame type ceiling.
• In an area where the temperature may fall below 0ºC or rise above
40ºC, such as garages and unfinished attics; this should also include
electrical boxes exposed to these environments.
• In dusty areas. Dust particles may cause nuisance alarm or failure to
alarm.
• In very humid areas. Moisture or steam can cause nuisance alarms.
• In insect-infested areas.
• In areas where the Relative Humidity (RH) is above 93%.
• Smoke alarms should not be installed within .9m of the following: the
door to a kitchen, the door to a bathroom containing a tub or shower,
forced air supply ducts used for heating or cooling, ceiling or whole
house ventilating fans, or other high air flow areas.
• Kitchens. Normal cooking may cause nuisance alarms. If a kitchen
alarm is desired, it should have an alarm silence feature or be a
photoelectric type.
• Near fluorescent lights. Electronic “noise” may cause nuisance alarms.
• Smoke alarms are not to be used with detector guards unless the
combination (alarm and guard) has been evaluated and found suitable
for that purpose.
• In front of forced air supply ducts used for heating and air
conditioning, near ceiling fans,or other high air flow areas.
2. Locations To Avoid
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 7

3. Installation Instructions
FIGURE 5
AA
FIGURE 6
FIGURE 7 FIGURE 8
mounting
bracket
The “A” line should be
horizontal and the “UP FOR
WALL MOUNTING” arrow
must be pointing up.
Alignment marks
Install Remove
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 8

3. Installation Instructions
MOUNTING INSTRUCTIONS
CAUTION: This unit is sealed. The cover is not removable!
1. Remove the mounting plate from the back of the alarm by holding the
mounting plate and twisting the alarm in the direction indicated by the
“OFF” arrow on the alarm cover.
2. To insure aesthetic alignment of the alarm with the hallway or wall, the
“A” line on the mounting plate should be parallel with the hallway when
ceiling mounting or horizontal when wall mounting.
3. After selecting the proper smoke alarm location as described in section 1,
attach the mounting plate to the ceiling as shown in figure 5. For wall
mounting see figure 6. Place mounting plate on the wall as described in
the mounting illustrations. Use the screws and anchors provided to
secure the mounting plate (use 3/16” drill bit for anchor holes).
4. Battery installation instructions are provided on the inside of the battery
door. To ensure proper installation of the smoke alarm battery, follow
the instructions.
5. When installing the battery, press the battery reminder finger down into
the battery compartment and install the battery
CAUTION! IF THE BATTERY REMINDER FINGER IS NOT HELD
DOWN IN THE BATTERY COMPARTMENT BY THE BATTERY,
THE UNIT WILL NOT ATTACH TO THE MOUNTING BRACKET.
6. Alignment marks are provided on the edge of the trim plate and the
alarm. After installing the mounting plate, place the alarm on the
mounting plate with the alignment marks lined up. Twist the alarm in the
direction indicated by the “ON” arrow on the alarm cover (see figure 8)
until it locks in place.
7. After installation, test your alarm by depressing and holding down the
test button for at least 5 seconds. This should sound the alarm.
!
!
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 9

4. Operation and Testing
OPERATION: The smoke alarm is operating once a fresh battery is
installed and testing is complete. When products of combustion are
sensed, the unit sounds a loud 85db pulsating alarm until the air is
cleared.
HUSH CONTROL: The “HUSH” feature has the capability of temporarily
desensitizing the alarm circuit for approximately 8 minutes. This feature is
to be used only when a known alarm condition, such as smoke from
cooking, activates the alarm. If the smoke is not too dense, the alarm will
silence immediately and the Red LED will flash once every 10 seconds for
approximately 8 minutes. This indicates that the alarm is in a temporarily
desensitized condition. The smoke alarm will automatically reset after
approximately 8 minutes and sound the alarm if particles of combustion
are still present. The “HUSH” feature can be used repeatedly until the air
has been cleared of the condition causing the alarm.
NOTE: DENSE SMOKE WILL OVERRIDE THE HUSH CONTROL FEA-
TURE AND SOUND A CONTINUOUS ALARM.
CAUTION: BEFORE USING THE ALARM HUSH FEATURE,
IDENTIFY THE SOURCE OF THE SMOKE AND BE CERTAIN A SAFE
CONDITION EXISTS.
FLASHING LED LIGHT: This smoke alarm is equipped with a flashing
red indicator light. The light is located under the test button and will
flash every 40 seconds to indicate that the smoke alarm is receiving
power.
TESTING: Test by pushing the test button on the cover and holding it
down for a minimum of 5 seconds. This will sound the alarm if the
electronic circuitry, horn, and battery are working. If no alarm sounds,
the unit has defective batteries or other failure. DO NOT use an open
flame to test your alarm, you could damage the alarm or ignite
combustible materials and start a structure fire.
TEST THE ALARM WEEKLY TO ENSURE PROPER OPERATION.
Erratic or low sound coming from your alarm may indicate a defective
alarm, and it should be returned for service (see section 11).
NOTE: WEEKLY TESTING IS REQUIRED.
Smoke alarms are designed to minimize nuisance alarms. Cigarette smoke
will not normally set off the alarm, unless the smoke is blown directly into
the alarm. Combustion particles from cooking may set off the alarm if the
alarm is located close to the cooking area. Large quantities of combustible
particles are generated from spills or when broiling. Using the fan on a
range hood which vents to the outside (non-recirculating type) will also
help remove these combustible products from the kitchen. If the alarm
does sound, check for fires first. If a fire is discovered, get out and call the
fire department. If no fire is present, check to see if one of the reasons
listed in section 2 may have caused the alarm.
5. Nuisance Alarms
!
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 10

6. Maintenance
BATTERY REPLACEMENT
Note: Replacement batteries are available where you purchased your
alarm.
To replace the battery, remove the alarm from the mounting plate by
rotating the alarm in the direction of the “OFF” arrow on the cover
(see figure 8).
This smoke alarm is powered by a 9V battery. A fresh battery should last
for one year under normal operating conditions. This alarm has a low
battery monitor circuit which will cause the alarm to “chirp”
pproximately every 30 - 40 seconds for a minimum of thirty (30) days
when the battery gets low. Replace the battery when this condition
occurs.
USE ONLY THE FOLLOWING 9 VOLT BATTERIES FOR SMOKE ALARM
BATTERY REPLACEMENT.
Alkaline type: ENERGIZER 522; DURACELL MN1604, MX1604;
GOLD PEAK 1604A.
NOTE: WEEKLY TESTING IS REQUIRED.
WARNING! USE ONLY THE BATTERIES SPECIFIED. USE OF DIF-
FERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT ON THE
SMOKE ALARM.
CLEANING YOUR ALARM
YOUR ALARM SHOULD BE CLEANED AT LEAST ONCE A YEAR
To clean your alarm, remove it from the mounting bracket as outlined in
the beginning of this section. You can clean the interior of your alarm
(sensing chamber) by using compressed air or a vacuum cleaner hose
and blowing or vacuuming through the openings around the perimeter
of the alarm. The outside of the alarm can be wiped with a damp cloth.
After cleaning, reinstall your alarm and test your alarm by using the test
button. If cleaning does not restore the alarm to normal operation the
alarm should be replaced.
!
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 11

7. Limitations of Smoke Alarms
WARNING: PLEASE READ CAREFULLY AND THOROUGHLY
• Fire-warning equipment for residential occupancies are capable of
protecting about half of the occupants in potentially fatal fires. Victims
are often intimate with the fire, too old or too young, or physically or
mentally impaired such that they cannot escape even when warned
early enough that escape should be possible. For these people, other
strategies such as protection-in-place or assisted escape or rescue
would be necessary.
• Smoke alarms are devices that can provide early warning of possible
fires at a reasonable cost; however, alarms have sensing limitations.
Ionisation sensing alarms may detect invisible fire particles (associated
with fast flaming fires) sooner than photoelectric alarms. Photoelectric
sensing alarms may detect visible fire particles (associated with slow
smoldering fires) sooner than ionisation alarms. Home fires develop in
different ways and are often unpredictable. For maximum protection,
the manufacturer recommends that both Ionisation and Photoelectric
alarms be installed.
• A battery powered alarm must have a battery of the specified type, in
good condition and installed properly.
• AC powered alarms (without battery backup) will not operate if the
AC power has been cut off, such as by an electrical fire or an open
fuse.
• Smoke alarms must be tested regularly to make sure the batteries and
the alarm circuits are in good operating condition.
• Smoke alarms cannot provide an alarm if smoke does not reach the
alarm. Therefore, smoke alarms may not sense fires starting in chim-
neys, walls, on roofs, on the other side of a closed door or on a differ-
ent floor.
• If the alarm is located outside the sleeping room or on a different
floor, it may not wake up a sound sleeper.
• The use of alcohol or drugs may also impair one’s ability to hear the
smoke alarm. For maximum protection, a smoke alarm should be
installed in each sleeping area on every level of a home.
• Although smoke alarms can help save lives by providing an early
warning of a fire, they are not a substitute for an insurance policy.
Home owners and renters should have adequate insurance to protect
their lives and property.
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 12

8. Good Safety Habits
DEVELOP AND PRACTICE A PLAN OF ESCAPE
• Make a floor plan indicating all doors and windows and at least two
(2) escape routes from each room. Second story windows may need a
rope or chain ladder.
• Have a family meeting and discuss your escape plan, showing
everyone what to do in case of fire.
• Determine a place outside your home where you all can meet if a fire
occurs.
• Familiarize everyone with the sound of the smoke alarm and train
them to leave your home when they hear it
• Practice a fire drill at least every six months, including fire drills at
night. Ensure that small children hear the alarm and wake when it
sounds. They must wake up in order to execute the escape plan.
Practice allows all occupants to test your plan before an emergency.
You may not be able to reach your children. It is important they know
what to do.
• Install and maintain fire extinguishers on every level of the home and
in the kitchen, basement and garage. Know how to use a fire
extinguisher prior to an emergency.
• Current studies have shown smoke alarms may not awaken all
sleeping individuals, and that it is the responsibility of individuals in
the household that are capable of assisting others to provide assis-
tance to those who may not be awakened by the alarm sound, or to
those who may be incapable of safely evacuating the area unassisted.
• There are situations where a smoke alarm may not be effective to pro-
tect against fire as noted by the NFPA and UL. For instance:
- Smoking in bed.
- Leaving children unsupervised.
- Cleaning with flammable liquids, such as gasoline.
- Fires where the victim is intimate with a flaming initiated fire; for
example, when a person's clothes catch fire while cooking.
- Fires where the smoke is prevented from reaching the detector due
to a closed door or other obstruction.
- Incendiary fires where the fire grows so rapidly that an occupant's
egress is blocked even with properly located detectors
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 13

Ionisation type smoke alarms use a very small amount of a radioactive
element in the sensing chamber to enable detection of visible and invisible
combustion products. The radioactive element is safely contained in the
chamber and requires no adjustments or maintenance. This smoke alarm
meets or exceeds all government standards. It is manufactured and
distributed under license from the U.S. Nuclear Regulatory Commission.
9. Ionisation Information
10. Additional Information
Smoke Detection - Where required by applicable laws, codes, or standards
for a specific type of occupancy, approved single- and multiple-station
smoke alarms shall be installed as follows:
(1) In all sleeping rooms and guest rooms
(2) Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft)
of any door to a sleeping room, the distance measured along a path of travel
(3) On every level of a dwelling unit, including basements
(4) On every level of a residential board and care occupancy (small facility),
including basements and excluding crawl spaces and unfinished attics
(5) In the living area(s) of a guest suite
(6) In the living area(s) of a residential board and care occupancy (small facility)
Are More Smoke Alarms Desirable? The required number of smoke alarms
might not provide reliable early warning protection for those areas separated
by a door from the areas protected by the required smoke alarms. For this
reason, the use of additional smoke alarms for those areas for increased
protection is recommended. The additional areas include the basement,
bedrooms, dining room, furnace room, utility room, and hallways not
protected by the required smoke alarms. The installation of smoke alarms in
kitchens, attics (finished or unfinished), or garages is not normally
recommended, because these locations occasionally experience conditions
that can result in improper operation.
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 14

11. Service and Warranty
LIMITED WARRANTY
The manufacturer warrants to the original purchaser that the enclosed
smoke alarm (but not the battery) will be free from defects in material and
workmanship or design under normal use and service for a period of three
years from the date of purchase. The obligation of the manufacturer under
this warranty is limited to repairing or replacing the smoke alarm or any
part which we find to be defective in material, workmanship or design, free
of charge to the customer, upon sending the smoke alarm with proof of
date of purchase, postage and return postage prepaid, to Warranty Service
Department, Lifesaver Products, Kidde Safety Europe Limited., Mathisen
Way, Colnbrook SL3 OHB
This warranty shall not apply to the smoke alarm if it has been
damaged,modified, abused or altered after the date of purchase or if it fails
to operate due to improper maintenance or inadequate A.C. or D.C.
electrical power.
THE LIABILITY OF KSE LIMITED OR ANY OF ITS PARENT OR SUBSIDIARY
CORPORATIONS ARISING FROM THE SALE OF THIS SMOKE ALARM OR
UNDER THE TERMS OF THIS LIMITED WARRANTY SHALL NOT IN ANY CASE
EXCEED THE COST OF REPLACEMENT OF SMOKE ALARM AND, IN NO
CASE, SHALL KSE LIMITED OR ANY OF ITS PARENT OR SUBSIDIARY
CORPORATIONS BE LIABLE FOR CONSEQUENTIAL LOSS OR DAMAGES
RESULTING FROM THE FAILURE OF THE SMOKE ALARM OR FOR BREACH
OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE
LOSS ORDAMAGE IS CAUSED BY THE COMPANY’S NEGLIGENCE OR
FAULT.
This warranty does not affect your statutory rights.
If after reviewing this manual you feel that your smoke alarm is defective
in any way, do not tamper with the unit.
Return for servicing to: Lifesaver Products, Kidde Safety Europe Limited.,
Mathisen Way, Colnbrook SL3 0HB 0800-917-0722 (See Warranty for in-
warranty returns)
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 15

QUESTIONS OR FOR MORE INFORMATION
Call our Consumer Hotline
(UK) 0800 917 0722
(Ireland) 1 800 818 601
Lifesaver is a brand of Kidde Safety Europe Limited
Kidde Safety Europe Ltd.
Mathisen Way, Poyle Road, Colnbrook, Berkshire SL3 0HB
0940-7217-01_V1.qxd:_ 2013.7.1 4:18 PM Page 16