Lifetime POWER LIFT 90757 User manual

TOOLS REQUIRED TABLE OF CONTENTS
ASSEMBLY INSTRUCTIONS
QUESTIONS? Model Number: 90757
Product ID:
Icon legend..................................................3
Warnings & notices......................................4
Pole assembly..............................................5
Pole-to-base assembly...............................10
Backboard-to-rim assembly......................15
Backboard-to-pole assembly.....................19
Parts identifier..........................................i–iv
Handle assembly.......................................23
Final assembly...........................................29
Moving the system.....................................34
Maintenance.............................................35
Warning sticker...........................................36
(x2)
(x1)
(x1)
(x1)
(x1)
(x1)
(x1)
(x1)
1/2" (≈13 mm), 7/16" (≈11 mm),
9/16" (≈14 mm), 3/4" (≈19 mm)
3/16" (≈5 mm)
(included)
325 lb (≈147 kg)
1/2" (≈13 mm)
(x2)
(x1)
(x1)
POWER LIFT™
BASKETBALL SYSTEM
MODEL 90757
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
• Decide with what to fill the base
(sand is recommended)
• At least 2 adults recommended for setup
BEFORE ASSEMBLY:
中文版，详见第2页。
Web Site: cn.lifetime.com

2
(x2)
(x1)
(x1)
(x1)
(x1)
(x1)
(x1)
(x1)
1/2" (≈13 mm), 7/16" (≈11 mm),
9/16" (≈14 mm), 3/4" (≈19 mm)
3/16" (≈5 mm)
(
包括 )
325 lb (≈147 kg)
1/2" (≈13 mm)
(x2)
(x1)
(x1)
POWER LIFT™
篮 球 架
MODEL 90757
Web Site: cn.lifetime.com
For English, see page 1.
安装说明书
· 准备场地
安装开始前，请您决定如何填充底座（推荐使
用沙子）。
· 征集亲朋好友
安装此产品需2个成年人。
烦请妥善保管本说明书以便更换零件时联系制造商。
所需工具
图标示意...............................3
警告与注意事项..................4
立柱安装步骤.....................5
立柱固定到底座的安装步骤...10
篮板和篮筐的安装步骤......15
篮板固定到立柱的安装步骤...19
零件识别..........................i–iv
把手的安装步骤..........23
填充底座........................29
移动篮球架.......................34
维护说明...........................35
警告贴纸....................36
目录
产品型号#与产品生产编码
（联系我们时需用到这两个号码）
产品型号：90757
产品生产编码：
联系我们 微信公众号：

3
• Indicates the parts to be used for a section.
• 表示组装该部份时所需的部件。
• Indicates special heed should be taken when reading.
• 表示在阅读时需特别留意。
• Indicates the hardware to be used for a section.
• 表示组装该部份时所需的五金器具。
• Indicates the tools to be used for a section.
• 表示组装该部份时所需的工具。
• Indicates no hardware required for a specific page.
• 表示该特定页面的组装不需要任何部件。
• Indicates no parts required for a specific section.
• 表示组装该特定部份时不需要任何部件。
• Indicates to use/not to use an electric drill for a specific step.
• 表示该特定步骤使用/不使用电钻。
ICON LEGEND / 󲌣󴇾󲌣󱛨
• These nuts are centerlock nuts. They are designed to be tight; therefore, they will be harder to tighten. Tighten until flush
with the metal or plastic.
• 这些螺帽为中心锁定螺帽。它们旨在起紧固作用；因此，它们在拧紧时需要用力。

4
• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Check base daily for leakage. Leaks will cause system to fall.
• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.
• Minimum operational height is 7 ft 6 in (2.3m) to the bottom of the backboard.
WARNINGS & NOTICES / 警告与注意事项
Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing
material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware
identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the
risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
SAFETY INSTRUCTIONS
安全事项
未遵守以下警告事项，可能导致人员严重受伤或财产损失并导致保修失效。
大部分受伤是由错误使用且/或未遵守安装说明造成的。使用本产品时请注意安全。
为确保本产品正常且安全运行，请所有者务必确保所有人员清楚了解注意事项并遵循操作守则。
为确保安全，请勿在未仔细阅读并遵守说明书指示的情况下，试图组装本产品。请检查整个包装盒及内部所有的零部件及/
或补充说明材料。开始组装之前，使用本文件中的零部件识别页面，辨别并清点零部件。恰当地完成组装、合理地使用及监督
是确保本产品正常运行并减少意外或受伤风险的基本前提。如果本产品未能恰当地组装、维护与操作，很可能会受伤严重。
•若在组装期间使用梯子，请特别小心，注意安全！
• 建议由两名有能力的成年人来组装本产品。
• 每日检查底座有无泄漏。泄漏将导致篮球架翻倒。
• 请正确安装立柱。否则在使用或移动过程中会导致立柱分离。
• 最小工作高度为距离篮板底部7英尺6英寸（2.3m）。
WARNING
Do not hang or swing on the ring.
警告
请勿吊挂或摇晃篮筐。

5
BCO
1
ADS (x2)
ABZ (x2)
ABB (x2)
AAF (x2)
ABE (x2)
ABR (x2)
CIH (x2)
9/16” (≈14 mm)
(x2)
ALH (x1)
ALF (x1)
(x1) (x1) (x1)
ALL (x1)
ALE (x1)
Hardware Bag / 五金配件包
HARDWARE REQUIRED / 所需五金配件
POLE ASSEMBLY / 立柱安装步骤
TOOLS REQUIRED / 所需工具
PARTS REQUIRED / 所需部件
Metal Part / 金属部件
• Warning Sticker applied to side not shown
• 警告贴纸粘在没有显示的那一侧。

6
SECTION 1 (CONTINUED) /步骤1（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
1.1
Large holes
大孔
Small holes
小孔
AAF (x2)
ABE (x2)
ABR (x2)
9/16" (≈14 mm)
ABB (x2)
ABE AAF
ALH ALH
ALL
ABB
ABE
ABR
(x2)
• Secure the pole bracket (ALL) to the top pole (ALH) with the hardware as shown.
• 使用如图所示的五金零件，将立柱托架(ALL)固定至上立柱(ALH)。

7
SECTION 1 (CONTINUED) /步骤1（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
• Align the hole in the bottom of the top pole (ALH)
with the slot in the top of the middle pole (ALF).
• 将上立柱(ALH)底部的孔位对准中立柱(ALF)顶部的
长孔。
• Secure the middle pole to the bottom pole (ALE) using
the same method as step 1.2.
• 使用与步骤 1.2 中相同的方法，固定中立柱(ALF)至下
立柱(ALE)。
1.2 1.3
!• The screw should be flush with the pole,
but will spin freely once inserted.
• 螺丝应该会与立柱齐平，但是插入后可
以自由转动。
Warning sticker
警示贴纸
!• The screw should be flush with the pole,
but will spin freely once inserted.
• 螺丝应该会与立柱齐平，但是插入
后可以自由转动。
1.2
ADS (x2)
1.3
CIH (x2)
ALH
ALF
ADS ADS
ALF
ALH
CIH
ALH
ALF
ALE
ALE
ALF
CIH
(x1)

8
SECTION 1 (CONTINUED) /步骤1（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
• Strike the end of the pole assembly on a piece of scrap wood or cardboard 5–6 times.
• 为了确保上中下三根立柱牢固的连接在一起，我们分别用立柱的两端用力撞击木块 5到 6 次。即使前面组装
时立柱已经很好的连接在一起亦不能跳过这个步骤。
1.4
6x
• Do not strike your feet with the pole sections, as
serious injury may occur.
• 撞击时注意脚下安全，以免受伤。 请误撞
击水泥或任何硬质地板，以免管身损坏。
!
• Flip the pole over and repeat step 1.4 for the opposite end of the pole assembly.
• 将立柱反过来，并且对立柱组件的另一端重复步骤 1.4。
1.5
6x
(x1)
WARNING / 警告
The Poles must be seated together! The Poles must be struck on a hard surface five to
six times! Failure to seat the Poles correctly could allow the Poles to separate during use.
务必使立柱紧紧卡在一起！立柱组件必须在硬面上锤打5-6下！如若立柱不能正
确地卡住，在使用过程中，将导致立柱坍塌。

9
SECTION 1 (CONTINUED) /步骤1（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
• Secure the poles together with self-drilling screws (ABZ).
• 使用自攻螺丝(ABZ)将立柱固定在一起。
1.6
ABZ (x2)
ABZ
ABZ
(x1)
• THE SCREWS (ABZ) ARE DESIGNED TO DRILL
INTO THE METAL OF THE UNDERLYING POLE.
For ease of installation, chuck the self-drilling
screws directly into the drill, or use a 3/8-inch
(≈10 mm) hex driver.
• 为了易于安装，将自攻螺丝直接用钻孔机钻
孔，或是使用一个 3/8”(10 mm)的六角起子。
!

10
2
BCQ
AAE (x2)
BTS (x1)
ABD (x4) AAO (x2)
EEO (x2)
AMU (x2)
AJM (x1)
(x2) (x1)
3/16" (≈5 mm)
(x2)
DRZ (x1)
1/2" (≈13 mm)
TOOLS REQUIRED / 所需工具
PARTS REQUIRED / 所需部件
HARDWARE REQUIRED / 所需五金配件
Plastic Parts / 塑胶部件
POLE-TO-BASE ASSEMBLY / 立柱固定到底座的安装步骤
Metal Part / 金属部件
AJC (x1) HJX (x1)
ALI (x2)
Long Axle / 󹛻󸮡 Short axle / 󵸠󸮡
ABL (x4)

11
SECTION 2 (CONTINUED) / 步骤2（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
2.1
2.2
• Lay the pole assembly down and slide the long axle (AJC) through a spacer (ABL), a wheel (AMU), a second spacer (ABL) and the
hole at the end of the bottom pole. Continue sliding the axle through a third spacer (ABL), the second wheel (AMU) and a fourth
spacer (ABL)as indicated. The ends of the axle should be equidistant from the center of the pole.
• 平放立柱组合，如图将󹛻󸮛󸮡)穿过一个󲐡󵑕，一 个 󸮛󲮚和另一个󲐡󵑕后插入下立柱最底下的
圆孔，在露出的轮轴一侧继续穿入第三个󲐡󵑕和第二个󸮛󲮚，最后再穿入第四个󲐡󵑕。󸘕󱝫󳥰󸮛󸮡
󱼑󱒷󶍐󴇝󲵪󱓩󲳳󺡬
• Slide the short axle (HJX) through hole next to the bottom hole so the ends of the axle are equidistant from the pole. Please
note that the two self-tapping screws from step 1.6 are on top.
• 如图将󵸠󸮡插入最底下圆孔上方的圆孔，同样保持短轴和下立柱居中对齐。󸘕󴪒󳘍󴟾󳺲󳟹󱗽󲍨󴠁󹿩󾙓󾙘󲰈󷿙󵯔
󱓝󹰷󷆦󳵮󷷹󱓓󳼎󴂝󱒶󵯔
ABL
ABL
AMU
AMU
ABL
ABL
AJC
ABL (x4)
HJX
Self-tapping screws
󷆦󳵮󷷹󱓓
Self-tapping screws
󷆦󳵮󷷹󱓓

12
SECTION 2 (CONTINUED) / 步骤2（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
AJM
Self-tapping screws
󷆦󳵮󷷹󱓓
• Set the front of the base (AJM) over the long axle as indicated. The ends of the long axle should be up inside the recesses in
the bottom of the base. Please note that the two self-tapping screws from step 1.6 are on top. These should be on top in order to have all the
other holes in the pole sections oriented correctly.
• 󲜾󲌣󲴉󳆵󳇕󵯔󱮆󸻉󱵐󸱞󹛻󸮛󸮡󽙓󹛻󸮛󸮡󵯔󱓝󶎙󳆳󱵐󱨮󳆵󳇕󳆵󸻉󵯔󱬓󴕵󱩣󸘕󴪒󳘍󴟾󳺲󴠁󹿩󾙓󾙘󲰈󷿙󵯔󱓝󹰷󷆦󳵮
󷷹󱓓󳆳󴂝󱒶󽙓󱗵󵻗󱝫󴟽󵻗󲰬󱹙󶍐󴇝󱒶󵯔󳡇󴁸󱩎󲯻󲮠
2.3
2.4 • Rotate the pole assembly upright until the short axle rests in the recess on top of the base.
• 如图旋转抬起立柱组合直至短轴卡进底座上的凹槽。
Short axle
Short axle

13
SECTION 2 (CONTINUED) / 步骤2（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
2.5
2.6
• While a second adult holds the pole upright, attach a pole brace (ALI) to the base as
indicated. Tighten only by hand at this time.Repeat this step for the second pole brace on the
other side of the pole and base.
• 一名成年人扶着立柱组合，另一名成年人按图示配件将󳵛󳰚󷅋固定到底
座上，󴟾󴠁󹿩󱗃󵥌󳡧󳥊󶡈󷷹󱓓󱵫󱸯󵲉󱹒󵯔󳹂󴩰󲰈󷿙󱸢󱒪󱜒󳵛󳰚󷅋
• Align the holes in the braces with those in the pole and secure the braces to the pole using the hardware indicated. Note the
bolt (DRZ) does not go all the way through the pole; the barrel nut (BTS) connects to it inside the pole. DO NOT completely tighten at this time.
• 󲜾󲌣󲳳󺡬󳵛󳰚󷅋󱼑󶍐󴇝󱒶󵯔󲮠󹙸󱨮󷷹󴈌󱼑󷷹󴣕󴪒󳘍󴟾󲙓󵯔󷷹󴈌󱒹󱙃󶊋󱬕󶍐󴇝󱸢󱒪󱜒󽙓󴅰󶓺󷷹󴣕󱼑󲯻󲍨
󶍐󴇝󱩣󸻉󸱡󳩺󴟾󴠁󹿩󱒹󵥌󲰏󱨴󹙸󶡈󷷹󴈌󱼑󷷹󴣕
AAE (x2) ABD (x4)
AAO (x2)
AAO
ABD
ABD ALI
ALI
AAE
BTS (x1)
DRZ (x1)
DRZ
BTS
“$#@*%!”
THIS STEP CAN BE DIFFICULT
DSA
BTS
EEO (x2)

14
SECTION 2 (CONTINUED) / 步骤2（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
2.7
2.8
• Lay the system down and keep it down until instructed otherwise. Securely tighten the hardware
indicated. DO NOT overtighten.
• 如图示方向放倒篮球架，󳥊󶡈󲌱󲌶󴇾󸗎󵯔󷷹󱓓󽙓󱙺󱒹󸅲󸰬󶡈
• Now, securely tighten the hardware from step 2.6.
• 󳥊󶡈󴠁󹿩󾙔󾙘󲰈󷿙󵯔󷷹󱓓󽙏󲌣󵑕󲌱󲌶󴇾󸗎󽙐
1/2" (≈13 mm)
(x2)
EEO (x2)

15
BCS
HARDWARE REQUIRED / 需要的零件
ABD (x2) ABF (x2)
AAM (x2)
ABK (x4)
AJW (x2)
APZ (x1)
AOW (x1)
AAV (x2)
DFE (x4)
AAA (x4)
AAJ (x2)
AJI (x1)
ALX (x1)
(x2) (x2) (x2)
7/16" (≈11 mm) 1/2" (≈13 mm) 9/16" (≈14 mm)
(x1)
BACKBOARD-TO-RIM ASSEMBLY / 背板与球框的组装
3
TOOLS REQUIRED / 所需工具
Plastic Parts / 塑胶部件
Metal Parts / 金属部件
Metal Parts / 金属部件
PARTS REQUIRED / 所需部件
DFD (x1)
AMY (x2)
ALD (x1)
DUC
DUC

16
SECTION 3 (CONTINUED) /步骤3（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
• Insert two bolts (AAM) with washers (ABD) and rubber washers (ABF) through the holes indicated in the back of the rim (ALX) as
shown. Secure the hardware with two T-nuts (AAJ).
• 插入两个螺栓(AAM)，附有垫圈(ABD)与橡胶垫圈(ABF)，穿过篮框(ALX)背后所指示的孔位，如图所示。使用两个 T 螺帽(AAJ)
固定五金零件。
• Ensure that the tap bolts (AAM) are positioned
on the outside edge of the holes as shown.
• 请确认带头螺栓(ABG)是装在如图靠外侧边
缘的孔上。
• Do not overtighten the hardware so much
that the rubber washers bulge as shown.
• 请勿过分拧紧螺丝以保持橡胶垫片向外
膨胀的状态。
!
!
1/2" (≈13 mm)
ABD (x2) ABF (x2)
AAM (x2)
AAJ
AAM
ABD
ABF
ALX
ABF ABF
AAJ (x2)
(x2)
(x1)
AAJ
AAM
ABD
ABF
3.1

17
SECTION 3 (CONTINUED) /步骤3（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
1/2" (≈13 mm)
3.2
ABK (x2)
APZ (x1)
(x2)
APZ
ALX
ABK
ALD
AAM
AJI
DFD
• Place the backboard face down onto a table, box or similar. Secure the rim (ALX) and plastic guard (ALD) to the backboard (AJI) with
the hardware shown.
•将将篮板面朝下放在桌子、盒子或类似物上。 如图将球框(ALX)和塑料保护片(ALD)安装到篮板(AJI)上。

18
SECTION 3 (CONTINUED) /步骤3（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
AAV
ABK
AOW
AJW
APZ
3.4 • Turn the backboard assembly over. Thread the jam nuts (AAV) onto each end of the U-bolt (APZ) and to the end of
the threads. Slide the compression springs (AJW) onto the U-bolt, and place the spring retainer plate (AOW) over the
compression springs. Secure the plate to the springs with the hardware indicated.
• 将篮板组件翻过来。将防松螺帽(AAV)锁在 U 形螺栓(APZ)的两端，尽可能锁紧。将压缩弹簧(AJW)滑入 U 形螺栓，并且将弹
簧固定片(AOW)置于压缩弹簧上。使用如图所示五金零件固定固定片至弹簧上。
AAV (x2) ABK (x2)
AJW (x2)
AOW (x1)
• DO NOT COMPLETELY TIGHTEN THE FLANGE NUTS IN THIS STEP!
Only tighten the nuts until the rim does not wobble. Tightening the
nuts will adjust the rim tension.
• 在这一步骤请勿过分拧紧尼龙凸缘螺母(ABK)，确保球框(ALX)
不会摇晃即可。
DFE (x4)
AAA (x4)
7/16" (≈11mm)
1/2" (≈13mm)
9/16" (≈14mm)
(x2)
!
3.3 • Attach the backboard brackets (AMY) to the backboard using the hardware indicated.
• 使用所指示的五金零件安装篮板托架(AMY)至篮板。
AAA
DFE
DFE
DFE
DFE
AAA
AMY
9/16" (≈14mm)
(x2)

19
7 5/8 in/po (≈19cm)
7 1/16 in/po (≈18cm)
4
(x2)
3/4” (≈19 mm)
(x1)
BCR
AKC (x2)
AAX (x4)
GBU (x2)
ABN (x8)
AAD (x2)
HMP (x2)
AKB (x2)
TOOLS REQUIRED / 所需工具
PARTS REQUIRED / 所需部件
HARDWARE REQUIRED / 所需五金配件
BACKBOARD TO POLE ASSEMBLY / 背板与立柱的组装
Metal Part / 金属部件

20
SECTION 4 (CONTINUED) /步骤4（续）
TOOLS AND HARDWARE REQUIRED / 所需工具及五金配件
7 5/8 in/po (≈19cm)
4.1
AAX (x1)
GBU (x1)
• Tighten the centerlock nut (AAX) until it is flush
with the end of the bolt.
• 拧紧六角螺栓(AAD)直到它的尾端与螺母
(AAX)齐平。
!
AKC
AKC
HMP
GBU
AAX
ABN
ABN
AKC
ABN (x2)
3/4” (≈19 mm)
(x2)
!
!
• Attach the short extension arms (AKC) to the backboard brackets in the location shown with the hardware indicated.
•如图将短伸展臂(AKC)用螺丝锁到背板支架上。
• A centerlock nut requires some effort to thread onto a
bolt. See page 3 for details.
• 中心锁紧螺帽需要一些力气才能拧到螺栓
上。详见第 3 页。
• If necessary, use a bolt to remove any
excess powder coating from the holes in
the backboard brackets.
• 如必要，使用一颗螺栓从篮板托
架的孔中除去多余的粉末涂层。
• DO NOT strike this bolt (GBU) with a mallet! If
there is difficulty sliding the bolt into place, use
a wrench to turn the bolt until it has advanced
into position.
• 请勿使用木槌敲击这个螺栓(DFB)！如
果滑入这个螺栓至定位有困难，使用
扳手转动螺栓，直到它向前进入位置
为止。
HMP (x2)