Lightmybricks LEGO Porsche 911 RSR 42096 Lighting Kit User manual

The following page is the instructions for the Light My Bricks LEGO Porsche 911
RSR (42096) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Porsche 911 RSR (42096) LED
light kit , please click here to view the product page
Light My Bricks: LEGO Porsche 911 RSR 42096
Lighting Kit

Package Contents:
12x White 15cm Bit Lights
6x Red Strip Lights
1x White Strip Lights
1x 8-Port Expansion Boards
1x 12-Port Expansion Boards
1x NC Push Board
2x 5cm Connecting Cables
4x 15cm Connecting Cables
3x 30cm Connecting Cable
1x AA Battery Pack (requires 3x AA Batteries)
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.

Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.
Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.

OK, Let’s Begin!
1.) Lift up the headlight covers and remove the two headlight sections as shown
below.

Take the left headlight and disconnect the trans clear round plates then take a
White 15cm Bit Light and with the cable facing down, place it over the top left
stud as shown below, with the cable laid in between studs. Secure it in place by
reconnecting one of the trans clear round plates over the top.
2.) Take another White 15cm Bit Light and using the same method as in
previous step, install it to the top right stud.

Install another 2x White 15cm Bit Lights to the two bottom studs as shown
below:
3.) Bring the four Bit Light cables together at the bottom of the headlight

section, then twist/wind them around each other 2-3 times to secure the cables
together. Ensure you hold the headlights in between your thumb and index
finger when twisting the cables to prevent the trans round plates from
popping off.
4.) Repeat the above steps to install 4x White 15cm Bit Lights to the right
headlight section.

5.) Take the 12-Port Expansion Board and connect all the lights from the two
headlight sections to it. Take your AA Battery Pack and insert 3x new AA
Batteries to it. Connect the battery pack cable to the expansion board, then
turn it ON to test the 8 lights from the headlights are working OK.