Lightolier A.D.A. TRIO FIXTURES Guide

READANDUNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTUFIE INSTRUCTIONSHEE
ISfwra is intesdedforinstallationin acznrdance with tha National Electrical Code and Ictal regulations.
assura full compliance witi local ccdas and regulations, thack with your Id electrical inspactor before
tallation. Toprevent elmtricel shcck, turn off elwtrici~ at fuw box bafora proceeding. IS:40616
Retaintheseirretrarctimraformaintenancereference. R0194 Page 10
INSTRUCTIONS FOR INSTALLATION OF A.D.A. TRIO FIXTURES.
COVERSFIXTURES 4tM16WH,4(K16WHE1,40616WHE2,4W16WHN1, 40616WHH1,40616WHN2,
40616sB,4W16SBE1,40616SBE2,40616SBN1,4LW16SBH1,40616sBN2,
40616SC,40616SCEl,40616SCE2,40616SCN1,40B16SCH1AND 40616SCN2
NOTE Thisinstructionsheetcoversbothcompactfluorescentandincandescenttypafirrturea.Althoughilhretrati(
showscompactfhaorescantversion,the incandescentversionassamblesandinstallsthasama.
IACKPIATE INSTALLATION:
1. Loosan two MOUNTING SCREWS in LOWER MOUNTING BRACKFE and ramove OIFFUSER ASSEMBLY by pulling OIFFUSER ASSE
from LOWER MOUNTING BRACKETS and unhooking ASSEMBLY from two UPPER MOUNTING BRACKETS (Fig. 1, Fig. 2 and Fig. 3).
2. Thraad CROSSBAR MOUNTING SCREWS into CROSSBAR as shown in Fig. 1.
3. Using appropriate slots in CROSSBAR, sacure CROSSBARto OUTLETBOX using OUTLET BOX SCREWS (providad with OUTLET60)
4. While supporting BACKPLATEmaka connations black fisture laad or fixtura Iaed without trmar marks to hot (black) supply Iaad; v
lead or fisture lead with tracar marks to nautral (white) supply Iced. Uninsulated fklura wire is aground wire and must be connect,
grounding tarminal or connections back into OUTLETBOX.
5. Position BACKPU+TE over CROSSBAR allowing CROSSBAR MOUNTING SCREWS to coma through holas in BACKPLATE.
CAUTION:Make certain wires ara not pinched between parts.
6. SacureBACKPL4TEbyinstallingtwoBA~ERYNUTSoverCROSSBARMOUNTINGSCREWSandtighten.
7. Installracommendadlamp(s).
CAUTION MAXIMUM WAITAGE AS MAFIKEDONFIXTUREMUST NOTBEEXCEEOEO.
o
CR
Sc
1-1 C3HTC>LIEl?’:::+’:~f~
—

NSTRUCTIONStlE~ NO.
1S:40616 INSTRUCTIONS FOR INSTALLATION OF A.D.A. TRIO FIXTURES.
COVERSFIXTURES40616WH,4M16WHE1, 4&16WHE2, 4tNi16WHNl, 4W16WHHI,
AW16WHN2,4061.6SB,40616SBE1,.40616SBE2,4LM16SBN1,40616SBH1,41W16SBN2,
lM6t Page2012 4iW16SC,~6SGEl, 60616SCEZ4W16SCN1,4Mi16SCHlANO 4M16SCM )
)IFFUSERINSTAU.ATION
1. HookDIFFUSIR ASSEMG4Yover UPPER.MOUNTINGBRACKETSallowing UPPERMOUNTING SCREWSto go down into holes in UPPERMOUNTING
WIACKETS,swing OIFFUSERASSEMBLYagainst EACKFLATE(Fig.2).
2. SecureOIFFUSERASSEMBLYin positionbytighteningtwo LOWERMOUNTING SCREWSinto LOWERMOUNTING BRACKETS(Fig.3).
/- wvMOuNT’NG
~ UFPERMOUNTING
iihACKET
RDIFFUSERASSEMBLY
JB
LOWERMOUNTING
SCREW
\-LOWERMOUNTING
BRAcKH
=GACKFIATE
M.2 FIG.3
●
●
●