Lightolier IS:1062LV User manual

WARNING: BEFORE INSTALLING REFLECTOR TRIM FRAME4N
KIT, READ MARKINGS IN REFLECTOR TRIM AND ON SOCKET CUP
OF FRAME-IN KIT TO DETERMINE LAMP WAllAGE AND TYPE
APPLICABLE FOR YOUR INSTALLATION. IF I.C. TYPE FRAME-IN KIT
IS USED, IT MAYBE INSTALLED IN DIRECT CONTACT WITH
INSULATED CEILING. IFA NON LC.TYPE FRAME-IN KIT IS USED, DO
NOT INSTALL INSULATION WITHIN 3INCHES OF FIXTURE SIDES OR
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH AMANNER
TO ENTRAP HEAT.
wY
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALUNG FtXTURE INSTRUCTION SHEET NO.
This fixture is intendedfor installationin accordancewith the NationalElectricalCode and local
regulations.Toassurefullcompliancewithlocalcafes andregulations,checkwithyourlocalelectrical
inspectorbeforeinstallation.Topreventelectricalshock,turnoffelectricityatfuseboxbeforeproceeding. IS:1062LV
Retain these instructions for maintenance reference. 0192 Page 1of 2
INSTRUCTIONS FOR INSTALLATION OF REFLECTOR TRIM 1062LV
IN THE 10OOLVFRAME- IN-KIT
?? s
Fig. AFig. BFig. CFig. D
1. FRAME-IN 2. CLOSE-IN 3. SNAP-ON 4. PUSH-UP
FRAM-INKIT MOUNTS
FLUSHON CEIUNG
.,. ... :.,- ....
ROTO-CUP
1.FRAME-IN (Fig. A) POSITION
See Frame-InInstructionSheetfor installationprocedure.
2, ROTATEROTO-CLIPS(Fig. B) Fig. E
As shownin Fig. E.
3, SNAP-ON (Fig. C) RECTANGLEHOLE
lnsertSOCKETthrough RECTANGLEHOLEontopof REFLECTORTRIM.
EngageTABfrom SOCKETCUPintoone of the SLOTSon top of
REFLECTORTRIM and pushotherendof SOCKETCUPwith LANCING
intothe other (Fig.F).
4. PUSH-UP(Fig. D)
PushREFLECTORTRIMintoceilinguntilflangeisflushto ceiling(Fig.D). SLOTS TRIM
\l (
NOTE: Socket manufacturers have suggested that socket may fail after
3to 6relampings. If this occurs, socket can be replaced by disconnect SOCKET
ing male connectors (attached to socket leads) and female connectors
(attached to fixture leads) and replacing it with anew socket procured
through LIGHTOLIER (Fig, G).
Fig. F
INSULATINGSLEEVING MALECONNECTORS(AllACHED TO SOCKETWIRE)
FEMALECONNECTORS(ATTACHEDTO FIXTUREWIRES)
-~@MR’’”KH
SEE BACK PAGE FORIAMPING INSTRUCTIONS Fig. G
1. Ies l“ITC>1.1E R“
i%%wyi!liwn

INSTRUCTION SHEET NO.
IS: I062LV
0192 Page 2of 2
LAMPING
1.Checkto sea that poweris OFF beforeIampingor relamping.
2. Removebaffleaperturefrom ELBOWby pullingstraightout (Fig.H).
3. Insertlamp(MR-16bulb) betweenlampsprings.
4.AttachSOCKETto hi-pin prongson LAMP.
5. InsertLAMPRINGwith LAMPand GLASS LAMP GUARD back into ELBOW.
WARNING:
A.LAMPMANUFACTURERSREQUIRETHEGLASSLAMPGUARDBEIN PLACE
BEFOREENERGIZINGLAMP, AND THAT GREAT CARE MUSTBE TAKEN
THAT LAMP IS FULLY COOLED BEFORERELAMPING.AVOID FINGER
MARKSON INSIDEOFLAMPFORTHEYMAYCAUSESHORT LAMPLIFEAND
POSSIBLE BREAKAGE.
B.USEONLY REFLECTORTRIMS PROVIDEDBY LIGHTOLIERINC. USE OF
OTHERMANUFACTURER’SREFLECTORTRIMSVOIDSTHEUNDERWRfTERS
LABORATORIESLISTINGAND COULD CONSTITUTE AFIRE HAZARD.
w“T““p
\
LGIASS LAMP
GUARD
~BAFFLE
Fig. HAPERTURE
NOTE:
1. LOW VOLTAGE FIXTURES should be dimmed only by specialdimmers intended specifically for that purpose. Use Lightolier,
Scenist, Crescendo VA, Neptune VA, Precision VA EasysetVA,Sunrise VA, Radiant VA, or equivalent products by others or
variable autotransformers or electronic dimmers intended for use with low voltage fixtures.
2. Lowvoltage fixtures may produce audible sound when used with dimmers, which maybe objectionable in acoustically critical areas.
JUNCTIONBOX
I_ [
TRANSFORMER
PRIMARY120V.60Hz
SECONDARY11.4V.
&5W.LOAO
Wwl II II 321/32’
I
+—---- 529/32’ FIANGE DIA.—--+
Fig. I
—
.-