Whittier Wood 2658AFGAC User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213Outside U.S. or Canada: 541- 687- 0213
800-653-3336800-653-3336
Fax: [phone] • Fax: [phone] • wwwwww.whittie.whittierrwood.comwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.AMail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use only.
recommended for commercial use.
Congratulations!
Production Code:
VN 08/08
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a handsome
addition to your home. For the best results, start
by reading the Assembly Instructions before you
begin your project.
Unload items from this unit prior to moving.
Do not overload shelves on this unit.
Do not climb, sit or stand on this unit.
Before loading or moving this unit, check all screws
and supports for tightness.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
Read the Assembly Instructions completely before
beginning your project.
Store the item: 1) in the box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
affect the stability of your furniture. Tighten or repair
as needed.
This Assembly requires two people.
Assembly Instructions
Model #
2658AFGAC
McKenzie
Hutch
Handle the glass plates with care. Glass is fragile.

A — 2658 Top Assembly
— Qty. 1 (Attached)
B — 2658 Case Only — Qty. 1
O – Plastic Shelf Bracket
– Qty. 14 (Attached)
P – Mending Plate – Qty. 2
E — Side Glass
— Qty. 2
(Installed)
C — Small Back Mirror
— Qty. 2 (Installed)
H — Large Glass Shelf
— Qty. 2
F — Door Glass
— Qty. 2
(Installed)
I — Center Door Glass
— Qty. 1 (Installed) — Qty. 1 (Attached)
J — Center Door Frame
K — Door Frame
— Qty. 2 (Attached)
Q — #6 x 3/4" Brass Flat
Head Screw — Qty. 56
(48 inserted)
G — Small Adjustable
Glass Shelf — Qty. 2
D — Large Back Mirror
— Qty. 1 (Installed)
2658AFGAC — Page 2 — 08/08
L — Knob — Qty. 3
(Installed)
M – #8 x 1½" Machine Screw
— Qty. 3 (Installed)
V – Magnetic Catch Kit
— Qty. 5 (Installed)
N — Hinge — Qty. 8
(Installed)
2658AFGAC McKenzie Hutch — Parts List
S — Nylon Restraint Strap
— Qty. 2
R — Clip — Qty. 4
T — #8 x 2" Black Screw
— Qty. 4
U — #8 x 1" Pan Screw
— Qty. 4
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model name.

2658AFGAC — Page 3 — 08/08
FIG. 1 H
FIG. 2
H
2658AFGAC McKenzie Hutch
Assembly Instructions
TOOL REQUIRED: Phillips Screwdriver
Fragile
Fragile
1. Install the lower Large Glass Shelf (H) first. Open the hutch doors. Using two people, turn the Large
Glass Shelf (H) sideways and carefully move the Shelf through the open left side door and behind the
vertical wood divider. Gently carry and move the shelf until it is entirely inside the unit. Rotate the shelf
horizontally so that it rests on the wood sides and Shelf Brackets (O). See Figure 1.
2. Again using two people, turn the second Large Glass Shelf (H) sideways and carefully move
the Shelf through the open left side door and behind the vertical wood divider. Gently carry and move
the Shelf until it is entirely inside the unit. Still holding the shelf vertically, lift it high enough so that it
goes past the Plastic Shelf Brackets (O). Turn the shelf horizontally so that it rests upon the back wood
divider and the Plastic Shelf Brackets (O). See Figure 2.

FIG. 3
G
G
O
Fragile
2658AFGAC — Page 4 — 08/08
FIG. 4
3. Gently place the Small Adjustable Glass Shelf (G) over the Plastic Shelf Brackets (O) as shown
in Figure 3. The height of the lower Plastic Shelf Brackets are adjustable.
4. Lift the McKenzie Hutch and place it flush against the back edge and centered side-to-side of the Buffet.

Q
P
Q
P
Q
P
P
x 2
Q
x 8
FIG. 5
FIG. 6
2658AFGAC — Page 5 — 08/08
N
5. Secure the Hutch to the Buffet by attaching two Mending Plates (P) with #6 x ¾" Brass Flat Head
Screws as shown in Figure 5.
6. On the right door, the middle Hinge (N) is a touch control for the inside lighting. See Figure 6a.
There are three settings. NOTE: During the first week or so, the control is extra sensitive and the light
settings may change just by moving your hand near the control or by touching the unit.
This will soon dissipate. NOTE: PLUG IN THE ELECTICAL CORD AND TEST YOUR HALOGEN
LIGHTING. If you experience problems, call Whittier Wood Furniture Customer Service.
FIG. 6a

Position unit at desired location. Locate stud in the wall behind unit. Attach Clip (R) to wall stud with
#8 x 2" Black Screws (T). See Figure 7a. Attach second clip to unit with #8 x 1" Pan Head
Screws (U). See Figure 7b. Connect the two clips with Nylon Restraint Strap (S). See Figures 7c
and 7d. If studs cannot be located, purchase proper tipping restraint hardware for your type of wall
and secure the unit according to that hardware’s directions.
Tipping Restraint
Note: When using the 2658AFGAC Hutch and the 2657AFGAC Buffet, secure the
2657AFGAC Buffet to the wall with tipping restraint sets included in the 2657AFGAC
Buffet hardware. Follow instructions below.
2658AFGAC — Page 6 — 08/08
7.
Fig. 7d
Fig. 7b
Q
N
Fig. 7a
P
N
Fig. 7c
N
PQ
O
Wall