Lightolier 40S20 Guide

flEADANDUNDEINTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFfXTURE INSTRUCTIONSHE~ NO.
hfkture is intended for installation in accordwwa with tie National Elmtrical codeendl~l raguletions.
Iassure full compliance with Ikcal codes and regulations, chsck with your lad elecEiwl inspector before
stallation. To prevent electrical shock, turn off elactricitf at fuse box befora procaading. IS:40620
Main Uresoinatruationsformaintaoaocarafaraoca. R0194 PaOa1of 2
INSTRUCTIONS FOR INSTAUATION OF A.D.A. LUNA
COVERSFIXTURES40S20,4DGZDN1.4W20H2
NOTE This instructionsheetcoversbothcompsctfluorescentandincandescenttypefirrturas.Altheughillustrationshews
compactfluoraacantvaraion,tha iocandaacantvaraionaaaamblessndinatallathaaamo.
3ACKP3ATE INSTALLATION:
Thread MOUNTING SCREWS into back of MOUNTING PLATEso MOUNTING SCREW HEAOStighten into recessed araa of MOUNTING PLATE(Fig. 1).
(Using the appropriate slots in MOUNTING PLATE,secura MOUNTING PIATE to OUTLETBOX using 011TL!3 BOX SCREWS (provided with
OUTLET BOX).
1. While supporting BACKPL4TE make contractions black fixture lead or fixtura without tracer marks to Rot(black) supply lead white fisture lead or
fisture lead with trecar marks to neutral (white) supply lead. Uninsulated fixtwa wire is aground wira add must be connested to grounding terminal
or ground lead inside OUTLETBOX. Use WIRE NUTS (local hardwara item). Push supply wires and wirEmut connections back into OUTLETBOX.
LPosition BACKPL4TE over MOUNTING PIATE allowing MOUNTING SCREWS to come through tha holq in BACKPLATE.
CAUTION Make certain wires are net pinchad batwaao parta.
j. SecureBACKPIATEinpositionbyinstallingthe‘@.voBATTERYNUTSoverMOUNTINGSCREWSandtighten.
i. Installrecommendedlamp.
ForCom act Fluoraacant Unite.
WARN~NG-(RISK OF FIRE) MOST DWELLINGSBUILTBEF~RE1BB5HAVESUPPLYWIRE RATEDSW C.CONSULTA
QUALIFIEDELECTRICIANBEFOREINSTALLATION.
NOTE If supplywiras are locatedwithinthraeinchesofballaaf,uaewire ratadforat IeaetWC.
CAUTION MAXIMUM WAllAGE AS MARKEDON FIXTUREMUST NOT BEEXCEEDEO.
a. .v’-’-’-
THUMBSCREW
9A
k.
0
/
BATTERYNUT
m

WTNUCTION SHE~ NO.
1S:40620 INSTRUCTIONS FOR INSTALLATION OF A.DJl LUNA (Continued)
COVERSFIXTURES4fM20,40B20N1,4W20H2
Iolw Page2Ofz
)IFFUSER lNSTALLhON
Position DIFFUSERso that recessed area of DIFFUSERLIPhooks war DIFFUSERCAT12Hon BACKPLATE (Fig. 2).
Swing DIFFUSERback againat SACKPlATE and sacure DIFFUSERin position by threading THUMB SCREW, into hole in the top
of BACKPIATE (Fig. 3).
CAUTION: Make certain that THUMB SCREWtightens into tha raceasad sres of the DIFFUSERLIP(Fig.3).Do not over I
tightanTHUMBSGREW.DIFFUSEifdamagacouldoccur.
/’-- THUMBSCREW 1
crTHuMBscRw
4
HG.9
..—