Lightware OPTJ Power tray Series User manual

Quick Start Guide
OPTJ Power tray SC
OPTJ Power tray NTD
OPTJ Power tray NTQ
Further Information
The Product brief of this appliance is available on www.lightware.com.
See the Downloads section on the dedicated product page.
Contact Us
[email protected]
[phone]
[email protected]
[phone]
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: 1.1
19200130
Important Safety Instructions
Please read the supplied safety instruction
document before using the product and
keep it available for future reference.
 The device is Class 1 laser product if the HDMI20-OPTJ-90 series extenders are installed.
Introduction
Thank you for choosing OPTJ Power tray series. The Power tray is a 1RU-size housing
accessory which can enclose up to 16 HDMI20-OPTJ-TX/RX90 units, also providing power
source for every installed device. The optical bers are connected to the eight SC duplex or
four Neutrik opticalCON QUAD or four Neutrik opticalCON DUO connectors, each carrying
four signal bers from four of the extenders. The HDMI tail cables of the extenders are
accessible directly at the back of the Power tray.
Model Comparison
Model Optical connector Number of installable
OPTJ extenders
OPTJ Power tray SC SC duplex (8x) up to 16
OPTJ Power tray NTQ Neutrik NO4FDW-A (4x) up to 16
OPTJ Power tray NTD Neutrik NO2-4FDW-A (4x) up to 8
Box Contents
OPTJ Power tray series
device
Cable tie (16x)
IEC power cable
Safety and Warranty Info,
Quick Start Guide
M3x6mm screw and toothed
foot washer (16x)
Front View
1
Status LED
indicators of the
OPTJ extenders
The status LED indicators give immediate feedback about
the recent status of the HDMI20-OPTJ-TX/RX90 extenders.
2
Power LED Power LED lights green when the unit is powered on.
3
AC connector Standard IEC power connector. Accepts 100 to 240 Volts,
50 or 60 Hz power sources.
4
Fiber optical
connectors
(variable by
models)
SC model: 8x SC duplex ber optical connectors for 16x
multimode SC ber optical cables.
NTD model: 4x Neutrik NO2-4FDW-A connectors for
4x Neutrik opticalCON DUO series cables or 8x LC ber
optical cables.
NTQ model: 4x Neutrik NO4FDW-A connectors for 4x
Neutrik opticalCON QUAD series cables.
5
Mounting slots
for the OPTJ
extenders
16x mounting slots for the HDMI20-OPTJ-TX/RX90
extenders.
Rear View
 The OPTJ Power tray NTQ model can be seen in the rear view picture but the layout of all three models is the same.
Assembly Steps of HDMI20-OPTJ-TX/RX90 Extenders
The following assembly guide is for help the correct installation of the HDMI20-OPTJ-TX/RX90
extenders to the Power tray step by step.
Step 1 - Removing of the small cover.
Remove the optical cables from the cable clamps located on the small cover. Remove the 8
pcs screws by a PH1 screwdriver from the locations highlighted with green arrows and remove
the small cover plate (grey colored).
Step 2 - Installation of the OPTJ extenders.
Insert each HDMI20-OPTJ-TX/RX90 extender to the mounting slot. Pull the HDMI tail cable
across the rear side mounting holes of the Power tray. Fasten the extenders by the provided
M3x6 screws and the toothed foot washers (2 pcs screws and 2 pcs washers per extenders
on the top).
Step 5 - SC ber cable connections.
Remove the protective caps and connect the SC ber optical cables to the extenders and
insert the optical cables to the cable clamps.
Step 4 - Re-inserting of the small plate.
Insert the small cover plate (grey colored) back and fasten the 8 pcs screws by a PH1
screwdriver.
Step 3 - USB cable connection.
Connect the USB-A cables of the extenders to the USB-A connectors of the Power tray (grey
colored). Fasten the USB cables with the provided cable ties.
 The USB-A connectors of the Power tray are for powering purpose only. No data
transmission is processed on them.
1 2
4 53
CLASS 1 LASER PRODUCT
IF OPTICAL EXTENDERS
ARE INSTALLED
Safety and
Warranty
Info
Quick
Start
Guide

300
444.5
482.6
44.2
444.5
482.6
44.2
444.5
482.6
44.2
300
min. 2
thread left
rack rail
device
mounting ear
rack screw
flat washer
cage nut
WARNING
To prevent injury, the apparatus is recommended to securely attach to the oor/wall or
mount in accordance with the installation instructions. The apparatus shall not be exposed
to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed
on the apparatus. No naked ame sources, such as lighted candles, should be placed on the
apparatus.
WEEE ( Waste Electrical & Electronic Equipment )
Correct Disposal of This Product
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or human
health from, uncontrolled waste disposal, please separate this from
other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased, this product,
or their local government ofce, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.
Class I Apparatus Construction
This equipment must be used with a mains power system with a protective earth connection.
The third (earth) pin is a safety feature, do not bypass or disable it. The equipment should be
operated only from the power source indicated on the product.
To disconnect the equipment safely from power, remove the power cord from the rear of the
equipment, or from the power source. The mains plug is used as the disconnect device, the
disconnect device shall remain readily operable. There are no user-serviceable parts inside of
the unit. Removal of the cover will expose dangerous voltages. To avoid personal injury, do not
remove the cover. Do not operate the unit without the cover installed.
The appliance must be safely connected to multimedia systems. Follow instructions described
in this manual.
Ventilation
For the correct ventilation and avoid overheating ensure enough free space around the
appliance. Do not cover the appliance, let the ventilation holes free and never block or bypass
the ventilators (if any).
Important Safety Instructions
Please read and keep the information in the attached safety instructions supplied with the
product before starting using the device.
Safety Symbols Legend
Symbol Description
Alternating current
Protective conductor terminal

Caution, possibility of electric shock
Caution
Laser radiation
Mechanical Drawings
The OPTJ Power tray NTQ model can be seen in the gures but the layout of all three models
is the same. The dimensions are in mm.
Front View (1:6)
Rear View (1:6)
Side View (1:6)
Top View (1:6)
Mounting with Rack Ears
The rack ears allow mounting the device as a standard rack unit installation.
 Always use all the four screws for xing the
device ears to the rack rail. Choose properly
sized screws for mounting. Keep minimum two
threads left after the nut screw.
 The device is rack-size width and 1U high.
Ventilation
 To ensure the correct ventilation and avoid
overheating let enough free space around the
appliance. Do not cover the appliance, let the
ventilation holes free on the front and the right
side.
Typical Application
HDMI 2.0 optical matrix assembly: by connecting the HDMI connectors outputs of the fully populated Power tray with the input and output ports of an MX2-8x8-HDMI20-Audio-L matrix a
HDMI 2.0 optical matrix system can be created with Full 4K UHD at 60 Hz 4:4:4 maximum resolution.
Specications
General
Compliance................................................................................................................ CE
EMC compliance (emission)..................................................................EN 55032:2015
EMC compliance (immunity) .................................................................EN 55035:2017
Safety................................................................................................. EN 62368-1:2014
RoHS .....................................................................................................EN 50581:2012
Laser safety ....................................................................................... EN 60825-1:2008
Laser class specication..............Class 1 if HDMI20-OPTJ-90 extenders are installed
Warranty ............................................................................................................. 3 years
Operating temperature ...................................................... 0 to +50°C (+32 to +122°F)
Operating humidity ......................................................... 10% to 90%, non-condensing
Cooling............................................................................................................... Passive
Protection against......................................................................Short circuit / Overload
Enclosure
Rack mountable........................................................................................................ Yes
Material ......................................................................................................... 1 mm steel
Dimensions (mm / inch).......................... 482.6W x 300D x 44.2H / 19W x 11.8D x 1.7
Net Weight ............................................................................................ 4.13 kg / 9.1 lbs
Power
Power supply ......................................................................................................Internal
Power source............................................................................100-240 V AC 50/60 Hz
Power consumption (loaded with 16 extenders)................................................ 23.7 W
Optical connectors - OPTJ Power tray SC
Connector type ............................................................................ SC duplex receptacle
Number of connectors .................................................................................................. 8
Optical connectors - OPTJ Power tray NTD
Connector type ..........................................................Neutrik NO2-4FWD-A receptacle
Number of connectors .................................................................................................. 4
Optical connectors - OPTJ Power tray NTQ
Connector type ............................................................. Neutrik NO4FWD-A receptacle
Number of connectors .................................................................................................. 4
USB connectors
Connector type ..........................................................................USB Type A receptacle
Number of connectors ................................................................................................ 16
DC output voltage.......................................................................................................5V
Installation of the OPTJ Extenders for the OPTJ Power tray NTD
The OPTJ Power tray NTD model is built with 4x Neutrik opticalCON DUO connectors which can extend up to 8x optical signals.
 The OPTJ Power tray NTD model is able to handle up to 8 pcs HDMI20-OPTJ-TX/RX90 extenders.
The mounting slots (highlighted with green) and the Neutrik opticalCON DUO connectors (highlighted with blue) are labeled with the same ID for the better identication. Thus, the installation of
the extenders are recommended to the following slots in the NTD model:
Mounting slots
1A (1) 1B (2) 1a (3) 1b (4) 2A (5) 2B (6) 2a (7) 2b (8) 3A (9) 3B (10) 3a (11) 3b (12) 4A (13) 4B (14) 4a (15) 4b (16)
Extender
installation  