Lilliput 629GL-70NP User manual

LILLIPUT TFT LCD
629GL-70NP/C/T
DEAR CUSTOMERS
Thank you for purchasing the liquid crystal display monitor. This product
employs new integrate circuits and high quality TFT LCD modules. It is
putting out with its low power consumption, emits no radiation, and other
advantage characteristics. This product is shaped with modern style and is
easy to be carried with. The color TFTLCD is the most suitable display for
VGA,VCD, DVD and GPS system for motorcars and ships .It also can be
used in the office ,in flat ,at home also in other suitable position. You will
certainly benefit from this monitor in lots of ways, to name some of them:
convenience, safety, space-saving.
We hope that you will have the enjoyment of your new mini color TFT
LCD.
To ensure the best use of the unit, please read this handbook carefully beforehand.
CAUTION
1. Please use the adapter attached in the accessory.
2. Do not expose this product to direct sunlight, heat or humid
conditions.
3. Keep away from strong light while using this product so as to
obtain the clearest and the most colorful picture.
4. Please avoid heavy impact or drop onto the ground.
5. Do not use chemical solutions to clean this unit. Please simply
wipe with a clean soft cloth to keep the brightness of the surface.

6. Ifthe product does not operate normally when the instructions are
followed. Adjust only those controls that are covered by the
instructions. Improper adjustment of other controls may result in
damage and will often require extensive work of a qualified
technician.
CONTANTS
1. PRODUCT DESCRIPTION -------------------
2. REMOTE CONTROLLER --------
3. MATCHED CABLE ---------------------------
4. CONNCETION ---------------------------
5. MENU OPERATION
IN AV MODE
BRIGHTNESS ADJUSTMENT------------------------------
CONTRAST ADJUSTMENT------------------------------
SATURATION ADJUSTMENT------------------------------
TINT ADJUSTMENT------------------------------
SHARPNESS ADJUSTMENT------------------------------
OSD LANGUAGE ------------------------------
RESET ------------------------------
OSD POSITION ------------------------------
OSD DURATION------------------------------
EXIT OSD ------------------------------
IN PC MODEM
BRIGHTNESS ADJUSTMENT------------------------------
CONTRAST ADJUSTMENT------------------------------
PHASE ADJUSTMENT------------------------------
CLOCK ADJUSTMENT------------------------------
OSD POSITION ADJUSTMENT------------------------------
RESET------------------------------
OSD COLOR TEMPERATURE------------------------------
OSD LANGUAGE------------------------------
OSD MISCELLANEOUS------------------------------
RETURN TO MAIN MENU---------------------------
OSD POSITION ADJUSTMENT---------------------------
OSD AUTO COLOR---------------------------
SATURATION ADJUSTMENT---------------------------
TINT ADJUSTMENT---------------------------
EXIT OSD------------------------------

6. ACCESSORIES ------------------------------
7. PARAMETER --------------------------
8. TROUBLESHOOTING -----------------------
PRODUCT DESCRIPTION
Picture 1
1. PC/AV: PC, AV switch.
2. <: Selection key, to select item on the OSD or push the key in PC
mode directly to adjust phase automatically.
3. MENU: To activate OSD menu.
4. >: To select function on OSD or to adjust the brightness directly.
There are six levels of brightness, push this button directly to
change among them.
5. Infrared receiving window
6. Vol- : Volume down or to adjust the value of setting function
7. Vol+: Volume up or to adjust the value of setting function
8. POWER: Power on/off
9. DC12V input jack
10.SKS input jack
11.Touch pen (for touch screen）
REMOTE CONTROLLER
Picture 2

: POWER ON/OFF
: MUTE
: Display inputted mode
: To activate OSD menu
: Volume down or to adjust the value of setting function
: Volume up or to adjust the value of setting function
: To select function on OSD
: To select function on OSD
: AV1, AV2, PC switch
~ : Number key, no use
: Unit, double-digit, three-Picture, no use.
: NO USE
: NO USE
: NO USE
MATCHED CABLES
Picture 3 (AV Cable)
1. SKS input end connect the SKS input jack of the unit
2. Black 9-pin plug for VGA signal input
3. Black jack DC12v power input
4. Yellow RCA jack for video 1 input
5. White RCA jack for audio input
6. Red RCA jack for video 2 input
Picture 4 (VGA cable)

1. Black 9-pin jack connect 9-pin plug of picture 3
2. USB end connect the USB port of computer for touch screen function.
3. 15-pin VGA signal input end connect VGA port of the computer
CONNECTION
Put the SKS input end of AV cable picture 3 into the AV input jack of the
monitor, the other jack of A/V cable should be connected with related signal
input as follows
1. Black 9-pin plug of picture 3 is connected to the 9-pin jack of picture 4 (note
the right direction of arrowhead),the VGA signal input end of picture 4 will
be connected to the VGA port at the back of computer ,then tighten the
screws . The USB end connects the USB port of the computer for touch
screen function.
2. Yellow RCA jack connect video signal 1
3. Red RCA jack connect video 2
4. White RCA jack connect audio signal
5. Black jack connect DC12v power
6. When you use the unit, please adopt matched DC adapter, if not, please
note that the power consumption should be less or equal to 10w.
MENU OPERATION
After connecting power, the unit will be in standby state .Press ”POWER”
on the unit or on the remote controller, the buttons of the unit will light ,the
POWER is red ,the others are blue, at that time the unit begins to work. Press
the same button again the unit will return to its standby state (Note the blue
button will black out in 5 or 6 seconds soon after you turn off unit.). When
it is working push “PC/AV” on the unit or on the remote controller to switch
between AV and PC.
IN AV MODE

.you can press “</>”on the unit or “ / ” on the remote controller to select
the item demanded among , , , , , , , , ,
, (in line: brightness ,contrast , saturation, tint , sharpness,
language , reset , OSD H- position, OSD V-position ,OSD duration, exit
OSD )and the selected item’s background will be yellow and the explanation of
the item will display in the window which on the right side of the OSD menu .
For touch screen function please download the driver for touch screen from
our website
BRIGHTNESS ADJUSTMENT
Press “</>”on the unit or “ / ” on the remote controller to
select ,and then press Vol+/ Vol- of the unit or / to adjust the
luminance of BRIGHTNESS as your desire. Then press “</>”on the unit or
“ / ” on the remote controller to select other item to adjust or to select
to exit the OSD. Other ways you can push “>” on the unit to switch the
level of brightness directly, there is 6 levels of brightness approved.

CONTRAST ADJUSTMENT
After activate MENU press “</>”on the unit or “ / ” on the remote
controller to select , then you can press Vol+/ Vol- of the unit or / to
adjust the level of contrast .After that press “</>”on the unit or “ / ” on
the remote controller to select to exit the OSD or select other item to
adjust .
SATURATION ADJUSTMENT
To adjust the saturation of image, press “</>”on the unit or “ / ” on the
remote controller to select , then push Vol+/ Vol- of the unit or / on
the remote controller to adjust the level of saturation. After adjustment select
to exit the OSD or select other item to adjust.
TINT ADJUSTMENT

The is to adjust the hue of image .Push Vol+/ Vol- of the unit or /
on the remote controller to adjust the hue of image as your desire after you
selected this object. Then press “</>”on the unit or “ / ” on the remote
controller to select other item to adjust or to select to exit the OSD.
SHARPNESS ADJUSTMENT
To adjust the sharpness of image you can operate as mentioned above
i.e. push “</>”on the unit or “ / ” on the remote controller to choose and
then press Vol+/ Vol- of the unit or / on the remote controller to adjust
the level of sharpness as your desire. After adjustment press “</>”on the unit
or “ / ” on the remote controller to select to exit the OSD.
OSD LANGUAGE
There is 8 language approved of the menu, namely English, French,

Deutsch, Espanol, Italiano, Nederland, Portuguese and Chinese. Push “</>”on
the unit or “ / ” on the remote controller to choose and then press
Vol+/ Vol- of the unit or / on the remote controller to select the langue
that you need. Then press “</>”on the unit or “ / ” on the remote controller
to select other item to adjust or to select to exit the OSD.
RESET
If you’d like to reset the adjustment ,press “</>”on the unit or “ / ” on
the remote controller to choose item; then push Vol+/ Vol- of the unit or
/ on the remote controller to choose “YES “ and it will reset to original
mode , after that you can reset adjustment of the unit as your desire once
more .
OSD POSITION ADJUSTMENT
The is to adjust the OSD position in horizontal direction, press
“</>”on the unit or “ / ” on the remote controller to select this item, then
push Vol+/ Vol- of the unit or / on the remote controller and the OSD
will move in horizontal direction .Press Vol+/ is to make the OSD move to

right, Vol-/ is to make the OSD move to left. After that press “</>”on the unit
or “ / ” on the remote controller to select other item to adjust or to select
to exit the OSD.
To adjust the OSD position in vertical direction you can select next item
and operate as follows,
-
The is to adjust the OSD position in vertical direction, press “</>”on the unit
or “ / ” on the remote controller to select this item, then push Vol+/ Vol- of
the unit or / on the remote controller and the OSD will move in vertical
direction as your operation. Push Vol+/ to make the OSD move up, push
Vol-/ is to make the OSD move down.
OSD DURATION
The duration of OSD is adjustable. Press “</>”on the unit or “ / ” on the
remote controller to select , then you can adjust the duration of OSD by
pressing Vol+/Vol- of the unit or / on the remote controller. Push
Vol+/ to extend the period of duration, push Vol-/ to shorten the period
of duration .The duration of OSD is up to 100 seconds.
EXIT OSD

After adjustment press “</>”on the unit or “ / ” on the remote controller to
choose and then push Vol+/Vol- of the unit or / on the remote
controller to select “YES“ and it will exit the OSD.
IN PC MODE:
You can press “</>”on the unit or “ / ” on the remote controller to select
the item demanded among , , , , , , , ,
, , (in line: brightness ,contrast , saturation, tint ,
sharpness, language , reset , OSD H- position, OSD V-position ,OSD
duration, exit OSD )and the selected items background will be yellow and the
explanation of the item will display in the window which on the right side of the
OSD menu . For touch screen function please download the driver for touch
screen from our website
BRIGHTNESS ADJUSTMENT

Press “</>”on the unit or “ / ” on the remote controller to select ,
and then press Vol+/ Vol- of the unit or / to adjust the luminance of
BRIGHTNESS as your desire. Then press “</>”on the unit or “ / ” on the
remote controller to select other item to adjust or to select to exit the
OSD. Other ways you can push “>” on the unit to switch the level of brightness
directly, there is 6 levels of brightness approved.
CONTRAST ADJUSTMENT
After activate MENU press “</>”on the unit or “ / ” on the remote
controller to select , then you can press Vol+/ Vol- of the unit or / to
adjust the level of contrast .After that press “</>”on the unit or “ / ” on the
remote controller to select to exit the OSD or select other item to adjust.
PHASE ADJUSTMENT
Press “</>”on the unit or “ / ” on the remote controller to select . Then

push Vol+/ Vol- of the unit or / on the remote controller to adjust the
beginning point and terminal point of image station. After adjustment select
to exit the OSD or select other item to adjust.
CLOCK ADJUSTMENT
The is to adjust the range of image station .Push Vol+/ Vol- of the
unit or / on the remote controller to adjust the range of image as your
desire after you selected this object. Then press “</>”on the unit or “ / ” on
the remote controller to select other item to adjust or to select to exit the
OSD.
OSD POSITION ADJUSTMENT
The is to adjust the OSD position in horizontal direction, press
“</>”on the unit or “ / ” on the remote controller to select this item, then
push Vol+/ Vol- of the unit or / on the remote controller and the OSD
will move in horizontal direction .Press Vol+/ is to make the OSD move to
right, Vol-/ is to make the OSD move to left. After that press “</>”on the unit
or “ / ” on the remote controller to select other item to adjust or to select
to exit the OSD.
To adjust the OSD position in vertical direction you can select next item

and operate as follows,
-
The is to adjust the OSD position in vertical direction, press “</>”on the
unit or “ / ” on the remote controller to select this item, then push Vol+/
Vol- of the unit or / on the remote controller and the OSD will move in
vertical direction as your operation. Push Vol+/ to make the OSD move up,
push Vol-/ is to make the OSD move down.
RESET
If you’d like to reset the adjustment ,press “</>”on the unit or “ / ” on
the remote controller to choose item; then push Vol+/ Vol- of the unit or
/ on the remote controller to choose “YES “ and it will reset to original
mode , after that you can reset adjustment of the unit as your desire once more
OSD COLOR TEMPERATURE
Color temperature of OSD is adjustable. Press “</>”on the unit or “ / ”
on the remote controller to select , you can choose to set color temperature
at first such as: 6500 Ks, 7500 Ks or 9300 Ks. You can also adjust a color

temperature that wants the options “USER" then can adjust RED, GREEN and
BLUE at will. With attain which want of the color value
Then you can adjust the color temperature of OSD by pressing Vol+/Vol-
of the unit or / on the remote controller. Push Vol+/ or Vol-/ to
select which you want.
OSD LANGUAGE
There is 2 language approved of the menu, namely English and Chinese.
Push “</>”on the unit or “ / ” on the remote controller to choose and

then press Vol+/ Vol- of the unit or / on the remote controller to select
the langue that you need. Then press “</>”on the unit or “ / ” on the
remote controller to select other item to adjust or to select to exit the
OSD.
OSD MISCELLANEOUS
Press “</>”on the unit or “ / ” on the remote controller to select to
subdirectories.
⒈RETURN TO MAIN MENU
⒉OSD POSITION ADJUSTMENT
The is to adjust the OSD position in horizontal direction, press
“</>”on the unit or “ / ” on the remote controller to select this item, then
push Vol+/ Vol- of the unit or / on the remote controller and the OSD
will move in horizontal direction .Press Vol+/ is to make the OSD move to

right, Vol-/ is to make the OSD move to left. After that press “</>”on the unit
or “ / ” on the remote controller to select other item to adjust or to select
to exit the OSD.
To adjust the OSD position in vertical direction you can select next item
and operate as follows,
The is to adjust the OSD position in vertical direction, press “</>”on
the unit or “ / ” on the remote controller to select this item, then push Vol+/
Vol- of the unit or / on the remote controller and the OSD will move in
vertical direction as your operation. Push Vol+/ to make the OSD move up,
push Vol-/ is to make the OSD move down.
⒊.OSD AUTO COLOR
If you select “YES” it will be automatic color system or not, you can adjust the
saturation of color and tint of color to adjust the color as your favorite operate
as motion follows.
⒋SATURATION ADJUSTMENT

To adjust the saturation of image, press “</>”on the unit or “ / ” on the
remote controller to select , then push Vol+/ Vol- of the unit or / on
the remote controller to adjust the level of saturation. After adjustment select
to exit the OSD or select other item to adjust.
⒌TINT ADJUSTMENT
The is to adjust the hue of image .Push Vol+/ Vol- of the unit or
/ on the remote controller to adjust the hue of image as your desire after
you selected this object. Then press “</>”on the unit or “ / ” on the remote
controller to select other item to adjust or to select to exit the OSD.
EXIT OSD
After adjustment press “</>”on the unit or “ / ” on the remote controller to
choose and then push Vol+/Vol- of the unit or / on the remote
controller to select “YES“and it will exit the OSD.
ACESSORIES
Home AC adapter 1piece
Car power cord 1piece
SKS AV cable 1piece

VGA 9-pin cable 1 piece
Remote controller 1piece
Drive disk 1piece (For touch screen)
Manual 1copy
PARAMETER
PANEL TFT LCD 177mm (7-inch)1152000 Pixels
HIGH RESOLUTION 800×480 (VGA)
AVERAGE BRIGHTNESS 240cd/㎡(For touch screen)
VIEWING ANGLE 140°/ 120°(Horizontal/Vertical)
COLOR SYSTEM PAL-4.43,NTSC-3.58
INPUT VOLTAGE DC 12V
INPUT SIGNAL PC(VGA),AV1,AV2
POWER CONSUMPTION ≤100W
CONTRAST 500:1
SIZE 196×116×32.5(mm)
WEIGHT 474g
TROUBLE SHOOTING
※Only black-and-white image
Make the level of color saturation and brightness is proper.
※Power on but no picture
Make sure the AV &VGA cable is tightly connected from the video out
connector & VGA signal output connector. Make sure you are using the
standard power adapter coming with the monitor.
※Wrong or abnormal colors
If any color is missing, check the cables to make sure it is securely
connected. Broken or loose pins in the cable connector can cause a bad
connection.
※Remote controller doesn't work
Check the battery to make sure the battery is installed properly and make
sure it is not a low battery. The signal is interfered by some obstructions.
■ REMARK:
If there are still any problems, you can connect with the related deals
*If interruptive image occurs, it maybe that the VGA signal frequency isn’t
matched with normal standard
*It is a normal condition that some bright lines appear on the screen when you
turn the unit