linarie BURGUNDY LICV33RED User manual

www.linarie.com.au
LICV33RED
BURGUNDY
Retro Wine Fridge

TABLE OF CONTENTS
Additional information on products, accessories,
warranty, replacement parts and services can be
found at www.linarie.com.au
2
www.linarie.com.au
Correct Conditions of Use
The appliance is intended for use in the home and similar
environments only. It is not intended for commercial use.
The appliance is not suitable for outdoor use, non-stationary
installation.
The electricity connection must be made by a qualified
specialist. Installation must comply with the valid
standards, regulations and laws. All safety and warning
information and the operating and installation
instructions must be complied with.
This wine cooler can be only used to store various types
of wines
7. Methods of operation ...............................06
8. Routine maintenance & care instruction ..07
9. Storage of wine ....................................... 08
10. Ideal wine temperature ........................ 08
11. Troubleshooting ................................... 09
12. Environmental tips .................................10
12.1 Disposal considerations
12.2 Disposing your old appliance
13. Warranty and After sales .......................10
13.1 Warranty
13.2 After sales service
13.3 Replacement of spare parts
CAUTION
WARNING NOT
ALLOWED
Adherence to the directions for use in this manual is
extremely important for health and safety. Failure to strictly
adhere to the requirements in this manual may result in
personal injury, property damage and affect your ability to
make a claim under Linärie’s manufacturer’s warranty
provided with your product. Products must be used,
installed and operated in accordance with this manual.
You may not be able to claim on Linärie’s manufacturer’s
warranty in the event that your product fault is due to
failure to adhere this manual.
This symbol means that the safe
operation of the product and the
personal safety of the operator are
concerned, and that the operation
must be performed in strict compliance
with the requirements as specified
This symbol means
that the operator
must pay attention
to the information
as described
This symbol means that
the behavior as
described is not allowed
CONGRATULATIONS
Congratulations and thank you for choosing Linärie
to introduce a new comfort of cooking in your home.
We are sure you will find your new appliance a
pleasure to use and a great asset to your kitchen.
requirements in Australia. Inappropriate use can,
however, lead to personal injury and damage to
property.
This appliance complies with all relevant safety
In order to operate the unit correctly and safely,
please read this instruction manual carefully before
installation and usage. This user manual which
provides you with all required instructions related
to safety, installation, use and maintenance of
the appliance.
For future reference, please store this booklet in a
safe place and ensure that all users are familiar
with the contents. Pass them on to any future
owner of the appliance.
Record Model & Serial Number
Model:...........................................................................................
Serial Number ........................................................................
Register your product www.linarie.com.au
1. General Information .............................. 03
1.1 Appliance information
2. General Safety Instructions .................... 03
2.1 General safety information
2.2 Safety instruction - Installation
2.3 Correction use & Operation .....................04
2.4 Disassembling and Disposal
of the Appliance
2.5 Accessories and Spare parts
3. Technical data sheet ...............................05
4. Name of components .............................05
5. Precautions for installation .....................06
6. Precautions for operation .......................06

Cleaning & Maintenance
1. GENERAL INFORMATION
2. GENERAL SAFETY
A damaged appliance can be dangerous. If you find the
appliance is damaged or marked, you must report it within
7 days if you wish to claim for damage/marks under the
manufacturer’s warranty. This does not affect your statutory
rights. Do not use a damaged appliance.
The manufacturer's warranty will be invalidated if the
appliance is not repaired by a Linärie approved service
technician.
Faulty components must only be replaced by genuine Linärie
spare parts. The manufacturer can only guarantee the safety
of the appliance when Linärie replacement parts are used.
If the power cord is damaged, it must only be replaced by a
Linärie authorized service technician or suitably qualified
electrician in order to avoid a hazard.
Linärie cannot be held liable for noncompliance with these
instructions, resulting from incorrect or improper use or
operation.
1.1 Appliance Information
Unauthorized Modifications
Unauthorised modifications can cause the appliance to
pose risks. Do not conduct any modifications to the
appliance.
The device must be cleaned regularly. Dirt can lead to
damage or the buildup of odors. (See “Cleaning and
maintenance” section).
Always clean the appliance exactly as indicated in
the operating instructions.
Always ensure the appliance is switched off before
cleaning or replacing parts.
Clean the appliance immediately after any food
spillage and the filter regularly to keep the appliance
working efficiently.
There is a risk of fire if cleaning is not carried out as
described in these operating instructions.
Make sure no water penetrates inside the device when
cleaning. Do not use a steam cleaning appliance to
clean this appliance. The steam could reach electrical
components and cause a short circuit.
In areas which may be subject to infestation by
cockroaches or other vermin, pay particular attention to
keeping the machine and its surroundings in a clean
condition at all times. Any damage which may be
caused by cockroaches or other vermin will not be
covered by the machine warranty.
2.1 General Safety Instructions
Children and People with Special Needs
2.2 Safety Instructions - Installation
The appliance is NOT suitable for use by children
without supervision.
Young children should be supervised near the appliance
to ensure they do not play with this appliance.
Children may be able to wrap themselves in packing
material or pull it over their heads with the risk of
suffocation. Keep children away from any packing
material.
In order to avoid any potential hazard, the installation
instructions must be followed.
Observe all regional regulations for the installation of
ventilation systems.
During installation, maintenance and repair work, the
appliance must be disconnected from the mains
electricity supply. It is only completely isolated from the
electricity supply when:
– the mains circuit breaker is switched off, or
– it is switched off at the wall socket and the plug is
withdrawn from the socket.
Do not pull the mains connection cable but the mains
plug to disconnect your appliance from the mains
electricity supply.
Do not connect the appliance to the mains electricity
supply by a multi-socket unit or an extension lead.
3
The appliance complies with the stipulated safety
requirements in Australia. The user is responsible for
appliance cleaning and maintenance as well as its safe
use. Improper use can lead to personal injury and
damage to property.
www.linarie.com.au
Thisappliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabi-
lities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
applianceby a person responsible for their safety.
The appliance must only be installed and assembled by
trained specialists who are familiar with and comply with
the standard national regulations and supplementary
regulations of ventilation systems.
Extension leads are a fire hazard and do not guarantee
the required safety of the appliance.
Tampering with electrical connections or components
and mechanical parts is highly dangerous to the user
and can cause operational faults. Only open the housing
as described in the instructions given in “Installation”
section of this booklet. Under no circumstances should
any other parts of the housing be opened.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
INSTRUCTIONS

2.3 Correction use and Operation
4
THIS APPLIANCE MUST BE PROPERLY EARTHED. It is
most important that this basic safety requirement is
present and tested regularly and, where there is any
doubt, the household wiring system should be inspected
by a qualified electrician.
Linärie cannot be held liable for noncompliance with
these instructions, resulting from incorrect or improper
use or operation.
For safety reasons, this appliance may only be used after
it has been built in.
Reliable and safe operation of this appliance can only be
assured if it has been connected to the mains electricity
supply.
Before using the appliance, ensure that all packaging
materials are removed from the appliance and make
sure that the connection data on the data plate [voltage
(V) and frequency (Hz)] indicated on the appliance
corresponds to the voltage and frequency of the power
supply in your household. Consult a qualified electrician
if in doubt.
D
Cracks, fissures or fractures in the glass ceramic panels
Prevent water ingress. Never sprinkle or flush the cooler
using water, nor place the cooler in an area exposed to
moisture or water sprinkling, let alone filling the cooler
with water, so as to avoid impairment of the electric
insulativity of the cooler. Furthermore, failing to follow
such requirements may lead to electric shock and fire,
or other accidents.
After the cooler is put into operation, never touch its inner
icing surface, especially when your hand is wet; otherwise
the skin may stick onto the inner surface to get injured.
can damage the underlying electronics. Switch off and
disconnect the appliance immediately.
O NOT store or spray flammable materials in the
appliance or near this appliance while it is in operation
(e.g. aerosols).
www.linarie.com.au
WARNING
Due to the special characteristics of the tempered glass,
the tempered glass may be exploded at the probability
rate of 3‰- 5‰ according to the industrial estimate,
while this company will strictly control it within 3‰.
After the wine cooler is installed in place, the plug shall
be easily accessible to facilitate the removal of the cooler
plug in case of any accident.
Clean regularly surfaces that can come in contact with
food and accessible drainage systems. If the refrigerating
appliance is left empty for long periods, switch off, defrost,
clean, dry, and leave the door open to prevent mould
developing within the appliance.
Opening the door for long periods can cause a significant
increase of the temperature in the compartments of the
appliance.
The refrigerant isobutane (R600a) is contained within the
refrigerant circuit of the appliance, a natural gas with a
high level of environmental compatibility, which is
nevertheless flammable. During transportation and
installation of the appliance, ensure that none of the
components of the refrigerant circuit becomes damaged.
2.4 Disassembling and Disposal of the
Appliance
2.5 Accessories and Spare parts
(see the “Environmental Tips” section for best practices on
disposing of this appliance).
The device must only be disassembled by trained
specialists who are familiar with and comply with the
standard national regulations and supplementary
regulations of the local utility companies.
Work on electrical components must only be conducted by
trained electrical personnel.
Incorrect components can lead to personal injury or
damage to the appliance. Only use original Linärie spare
parts for repairs.
Modifications, additions or alterations to the appliance
can lead to safety risks. If spare parts or accessories from
other manufacturers are used, the warranty will be
invalidated, and Linärie cannot accept liability.
Please check www.linarie.com.au for more information.
Regarding the information pertaining to the installation,
handing, maintenance, servicing and disposal of the
appliance, thanks to refer to the paragraph
“ROUTINE MAINTENANCE and CARE INSTRUCTIONS”
and “TROUBLESHOOTING” of the manual.

5
www.linarie.com.au
3. TECHNICAL DATA SHEET
4. NAME OF COMPONENTS
Model LICV33RED LICV52BLUE LICV106GREEN
Rated voltage 220-240V ~
Rated frequency
50Hz
Climate type N / S T
Rated current 0.8A
Rated power of lamp 1.0W
Refrigerant R 600a/18g R 600a/18g R 600a/22g
Dimensions
( width *depth* height)
480*505*880
480*505*880 495*605*905 495*605*1325
Volume 94L 126L 201L
LICV33RED LICV52BLUE
1
2
3
4
5
6
Top cover
Display panel
Shelf
Glass door
Door gasket
Adjustment leg
1
2
3
4
5
6
Top cover
Display panel
Shelf
Glass door
Door gasket
Adjustment leg
1
2
3
4
5
6
7
Top cover
Display panel
Shelf
Glass door
Door gasket
Adjustment leg
Fan
LICV106GREEN
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
7

6
w ww . lina r ie .c om . a u
5. PRECAUTIONS FOR INSTALLATION
6. PRECAUTIONS FOR OPERATION
7. METHODS OF OPERATION
The fridge shall not betilted over 45°when being
handled, and it can be electrified only 10 minutes
after handling operation.
1. Clean the fridge.
2. Keep the fridge level. After the fridge is leveled and cleaned, do not electrify it immediately. Keep the fridge stationary
for more than 2 hours, and then electrify it to ensure the normal operation ofthe fridge.
3. Close the fridge door, and insert the power line. After the power supply is switched on, the fridge will start to work.
Ifthe fridge fails to work in a long period oftime, check whether the power socket and the electric circuit work normally .
If, half an hour later, anabrupt reduction oftemperature is detected after the fridge door is opened, the cooler works
normally. After 2~3 hours, adjust the temperature and then fill wines according the instruction. It is normal the
compressor will work for a longer time for the initial plugging, and then works intermittently.
4. Generally, do not stop the fridge, to avoid influencing its normal service life. After the power line plug is removed, wait
for at least 5 minutes before inserting it again, to ensure the normal operation ofthe fridge.
5. Do not switch off the power supply ofthe fridge when unnecessary, because the power interruption may cause
temperature rise inside the fridge, thus to shorten the storageterm ofwines and degradetheir drinking quality.
6. A certain space shall be maintained between wine bottles, which will facilitatethe circulation of coolair. The figure
illustrates the layout of shelves that result in the most efficient use of energy for the refrigerating appliance.
7. It is not allowed to flush the fridge body using water, nor to wipe the body using the gasoline orother organic solvents.
8. Ifthe power cord is damaged, it must be replaced by the professional ofthe manufacturer, its repair department orany
similar department to avoid any danger.
9. All power sockets must be reliably earthed.
10. The system shall be set up during the initial operation ofthe product for better protection ofthis product.
Power key Illumination lamp key
Child lock key (combined key)
Lock: No setting can be changed when the lock is activated. Lock is automatically activated 30
seconds after a setting is changed orthere is no activity. When engaged, pressing any key
will result in a 2 beep alarm.
Unlock: To deactivatethe auto lock, press both keys simultaneously for 5s. Any operation should
be in unlock mode.
Celsius degree/ Fahrenheit degree switchover key (combined key)
Press both keys simultaneously for 5s, and then you can switch over between the Celsius degree
and Fahrenheit degree for display. Each time the key is pressed, a switchover will be made.
When setting the system temperature, it is not allowed to switch over between the Celsius degree
and Fahrenheit degree.
Temperature “+” keyTemperature “-” key
The fridge must beplaced ona flat and solid
ground surface. If it needs to be elevated, a stable,
solid and inflammable pad shall beused. Never
the packaging foamasthe pad to elevatethe fridge.
Do not place the fridge in the area exposed to
moisture orwater splash. The water splash or
on the fridge shall betimely removed using the
soft clothto prevent rusting and impairment of
electric insulativity.
Do not place the fridge in an environment lower
than 5 Celsius degree, nor use it in the rain.
The fridge shall be kept far away from the heat
source and protected against sunshine, to avoid
influencing the normal operation ofthe fridge.
The appliance is only applied with power supply of
single phase alternating current of220~240V/50Hz.
The device uses a wall socket earthed according to
current recommendations.
If the power cable is damaged, do not proceed with
his replacement but contact yourafter-sales service.
The socket must be readily accessible but out of
reach of children. Ifunsure, contact your installer.
The fridge shall bewell ventilated; otherwise the
normal operation ofthe fridge may beadversely
influenced. The ventilated space must beat least
20cm from the both sides ofthe fridge and 10cm
from the top and back sides ofthe fridge.
Quick start

7
www.linarie.com.au
cont. methods of operation
8. ROUTINE MAINTENANCE AND CARE INSTRUCTIONS
Power on/off key:
1. Press this key for 5S, and then all external power sources will be disconnected and all external equipment will
be turned off, with the cooler in ready mode, the display screen will indicate “οF” for 60s.
2. When the cooler is in the ready mode, touch any key to light the display screen and then press this power key
for 5S, the cooler will restore its normal operation and work under real-time conditions.
Lamp on/off key:
The lamp control key is a cycling key: Normally on --> Normally off --> Normally on.
Temperature “+” key:
1. Functions of temperature “+” key: In locked mode, the action of any key is detected, the
display screen will indicate the current set temperature. After unlock operation, this key can be operated to
increase the set temperature by 1°C each time the key is pressed. The display screen will indicate the current
set temperature in a flashing way and at a certain interval, and 5s later, if no further action of this key is
detected, the setting after adjustment will be memorized, and the screen will exit from the flashing mode and
restore the indication of the set temperature.
2. Rules of temperature adjustment: For example: 5°C (current set temperature)
-->6°C -->7°C -->8°C --> . . . -->20°C.
1. To develop the best performance of this machine and prolong its service life, it shall be serviced frequently.
Before maintenance, the power line plug shall be removed and it shall be confirmed that the power supply
has been cut off.
2. It is not allowed to remove the power line plug from the socket by pulling the cable.
3. The cooler inside shall be thoroughly cleaned every year. To clean the cooler,
the plug shall be removed and the cooler shall be emptied. Then the cooler
inside shall be cleaned using the wet soft cloth or sponge dipped with
clean water or soap liquid (or any other non-corrosive neutral cleanser).
It is not allowed to clean the cooler using the organic solvent, alkaline
detergent, boiled water, washing powder or acid and the like.
4. In the humid environment or in the rainy weather, the cooler surface may
be dewed, especially on the external surface of the glass door. This is
caused due to the contact with the moisture in the air. In such a case,
the surface can be dried using the dry cloth.
5. To ensure the normal operation of the cooler in a long period of time,
the user should inspect the cooler on a regular basis; if any abnormality
is found, the manufacturer shall be notified of the same immediately.
6. During cleaning operation, it is not allowed to use the water to flush the
compressor compartment of the cooler. After cleaning operation, the
cooler shall be wiped using the dry cloth to prevent rusting.
Temperature “-” key:
1. Functions of temperature “-” key: this key can be operated to decrease the set temperature by 1°C each
time the key is pressed. The display screen will indicate the current set temperature in a flashing way and
at a certain interval, and 5s later, if no further action of this key is detected, the setting after adjustment
will be memorized, and the screen will exit from the flashing mode and restore the indication of the set
temperature.
2. Rules of temperature adjustment: For example: 20°C (current set temperature)
-->1 9°C -->1 8°C -->17°C --> . . . 5°C.
Alkalescent
Kitchen detergent Gasoline, thinner
alcohol, acid, petroleum
Brush

8
www.linarie.com.au
Red wine storage zone:
The storage zone is mainly intended to ensure the storage of your red wine under the best conditions.
The temperature of the storage zone has been set at 12°C at the delivery, and this temperature is suitable for the storage of
most of wine products.
The red wine is provided with a complicated nature due to its length of treating process. To express its best feature, a specific
environment is needed. Although all of wine products are manufactured at the same temperature, they need to be preserved
and tasted under different temperature conditions due to their special features.
Therefore, as for the coolers of the wine manufacturer, the absolute temperature is not essential for the storage of wine.
However, a steady temperature is very important within a certain period of time. The wine can be properly preserved at any
temperature as long as its temperature is not changed.
9. STORAGE OF WINE
10. IDEAL WINE TEMPERATURE
Disusing
If it is not used for a long time, turn off the wine cooler, pull out the plug and take off the safety device or break the fuse.
Do a good job in cleaning and open the cabinet door so that no smell will be produced.
Amarone Classic Dry Red Wine 17°C
Amarone Classic Dry Red Wine 17°C
Barbaresco Wine 17°C
Barolo Wine 17°C
Beaujolais Wine 13°C
Bordeaux Blanc 6°C
Dry white wine 8°C
Bordeaux Red Wine 17°C
White Burgundy 11°C
Red Burgundy 18°C
Brunello Wine 17°C
Champagne 6°C
Chianti Classico 16°C
Languedoc-Roussillon 13°C
Passito di Pantelleria 6°C
Provence Rose 12°C
Sweet Sparkling Wine 6°C
Verdicchio di Matelica & Verdicchio dei Castelli di Jesi 8°C
Trentino White Wine 11°C
Franciacorta White Wine 11°C
Aromatic White 10°C
Fruity Dry White 8°C
Friulano Venetian Julia White Wine 11°C
Rodano White Wine 15°C
Loire Dry White Wine 10°C
Loire Liqueur Wine 10°C
Loire Red Wine 14°C
Passito Liqueur Wine 8 - 18°C
Rose Wine, New Wine 12°C
Light Red Wine with Malt Tannins 14°C
Red Wine with a Little of Tannins 16°C

9
w w w . lina rie . c om . a u
11. TROUBLESHOOTING
Status Reason and solution
Too high noise.
If you find any abnormality during operation, immediately stop the operation, remove the power line plug,
and check the machine according to the following instructions. If necessary, contact the after-sales service
center of this company.
The fridge is not level.
The power supply is not switched on.
The computer board is damaged.
The compressor is provided with a
protection mode
The door is opened too frequently or
the door is opened for too long time.
The external environment is highly
humid.
The illumination lamp is damaged.
Check whether the power supply is
switched on.
The door seal may be hardened or
deformed due to the low temperature
inside the fridge after operation for a
period of time.
Use the hot air of the hair dryer to bake
the deformed surface or use the hot
towel to cover the deformed surface,
and close door and press it tightly after
the door seal is softened.
Notify the manufacturer for
replacement of the lamp.
Check the power supply.
The fridge temperature is set too low.
Level the fridge, for the unleveled fridge
may produce noise during operation.
Switch on the power supply.
Notify the manufacturer for repair.
The operation interval of the
compressor is 5 minutes.
Do not open the door for too long time,
nor open or close the door too
frequently.
Dry using a piece of dry cloth.
Set a proper temperature.
The fridge doesn't
work.
The fridge door
surface is dewed.
The illumination lamp
is not lit.
The door is not
properly sealed and
there is a leakage
of cool air
- If the temperature in the summer is too high, the compressor will work for
long time. This is normal.
- If the fridge is not cool enough, please check against the following items:
- If the fridge door is not properly sealed or the door is opened too frequently,
close the door tightly, and open the door at a lower frequency. Do not place too
many drinks in the fridge, and maintain a certain space between foods.
- If the temperature inside the cooler reaches too low required temperature,
check the temperature setup, and set the temperature at a higher level.
The compressor keeps
operating for long
time.
- Adjust the refrigerating level.
- The fridge is exposed to sunshine or any heat source is located in its
immediate area.
- Any hot drink is placed into the fridge.
- The drinks in the fridge are crowded to impair the cool air circulation.
- The fridge door is frequently opened or is not properly closed.
The refrigerating effect
of the fridge is poor.
- The new fridge may give off the smell of the foaming agent or plastic.
That’s normal, and such smell will disappear slowly in future.
Check whether there is any spoiled drink inside the fridge.
Any odorant drink shall be tightly sealed using the plastic bag.
The fridge shall be cleaned on a regular basis.
There is any odor in
the fridge.
- The sound is generated from the flowing of the refrigerant inside the circulating
pipeline of the refrigerating system. That’s normal.
- No further treatment is required.
- This is the sound generated in the startup of electric components, such
as the relay and thermal protector, during start or stop of the fridge.
- This is caused by the mutual fine movements of various kinds of materials due
to the inconsistent thermal expansion and contraction arising out of abrupt
changes of the fridge inside temperature when the fridge is being started
or stopped.
The fridge produces
the liquid flowing
sound.
The fridge produces
snapping sound in
operation.

16
12.2 Disposing of your old appliance
12. ENVIRONMENTAL TIPS
13. WARRANTY & AFTER SALES SERVICE
The transport and protective packaging has been selected
from materials which are environmentally friendly for
disposal, and can normally be recycled.
Recycling the packaging reduces the use of raw materials
in the manufacturing process and also reduces the
amount of waste in landfill sites. Ensure that any plastic
wrappings, bags etc. are disposed of safely and kept out
of the reach of babies and young children. Danger of
suffocation.
Observe all safety and warning information during
operation (see the “General Safety Instructions” section).
Observe all safety and warning information during
operation (see the “General Safety Instructions” section).
Incorrect components can lead to personal injury or
damage to the appliance. Use only genuine original
Linärie spare parts.
Modifications, additions or alterations to the appliance
can lead to safety risks. If spare parts or accessories from
other manufacturers are used, the warranty will be
invalidated, and Linärie cannot accept liability.
Please check www.linarie.com.au for more information.
Model:…………………………………………………………
Serial Number:.………………………………………………
Register your product www.linarie.com.au
In the event of a fault which you cannot remedy yourself,
please contact Linärie.
The manufacturer’s warranty for this appliance is 2 years.
The contact details for Linärie are given at the beginning
and of these instructions.
When contacting Linärie, please quote the model and
serial number of your appliance. These can be found on
the data plate, after removing the grease filter.
Electrical devices marked with this label may not be
disposed of in domestic waste at the end of their service
life.
Electrical and electronic appliances often contain valuable
materials. They also contain specific materials, compounds
and components, which were essential for their correct
function and safety. These could be hazardous to human
health and to the environment if disposed of with your
domestic waste or if handled incorrectly. Please do not,
therefore, dispose of your old appliance with your
household waste.
Please dispose of those materials by contacting your local
authorities and ask for the correct method of disposal.
Please ensure that your old appliance poses no risk to
children while being stored prior to disposal.
By disposing of this product in accordance with the
regulations, you protect the environment and the health of
those around you from negative consequences.
12.1 Disposal considerations
13.1 Warranty 13.3 Replacement of spare parts
13.2 After sales service
Record model & serial number
www.linarie.com.au

LIKE TO
KNOW MORE?
© Linärie
For further information on all Linärie appliances,
or to obtain detailed dimension and installation
information, phone or email our Customer Care
team or visit our website:
Australia
[email protected]
www.linarie.com.au
Follow Us
@Linarie.Appliances
www.linarie.com.au

Operating and installation instructions: Original √ Translation
Linärie Contact
[email protected]
www.linarie.com.au
The distribution and duplication of this document, as well as the use and disclosure of its contents
are prohibited unless expressly authorised.
These operating and installation instructions have been drawn up with the greatest of care. But it
cannot be ruled out that subsequent technical modifications have not yet been incorporated or
the relevant content has not yet been adapted. Please accept our apologies in this eventuality. An
updated version can be requested from our team. Subject to printing errors and mistakes.
© Linärie
All rights reserved.
www.linarie.com.au
Mart Online Services Pty Ltd.
ACN 657 824 050