Lincat SEAL PBG5 Guide

IS279 ECN2885
INSTALLATION AND USER
INSTRUCTIONS
REFRIGERATED FOOD
PREPARATION BAR ACCESSORIES

IS279 ECN2885 Page 2
Dear Customer,
Thank you for purchasing this Lincat product.
This is just one of over 300 different items of catering equipment available which is
constantly being extended and improved. Details are available from your local
distributor or direct from us.
Used for the purposes for which it is intended, and with careful maintenance as
outlined in this User Guide, your Lincat product will give years of trouble free use.
IMPORTANT INFORMATION
Please read all of the safety and operating instructions carefully
before using this product. Please pay particular attention to all
sections of this User Guide that carry warning symbols and notices.

IS279 ECN2885 Page 3
CONTENTS
PRODUCT SPECIFICATION
Contents Page
Product specification………………………………………………….. 3
Back-service glass ……..……………………………………………… 4-5
Stainless steel lid………………………………………………………. 6
Food Preparation Bar Back Service Glass – PBG5, PBG7
Food Preparation Bar Lid – PBL5, PBL7
These instructions are for your guidance and refer to the accessory ordered.
For installation and use of your Food Preparation Bar, follow the instructions
supplied.

IS279 ECN2885 Page 4
BACK SERVICE GLASS
Pack contents:
2 x Three-Corner Brackets
4 x Two-Corner Brackets
4 x Glass Supports
8 x M4 x 10 Countersunk Screws
14 x M5 x 8 Domehead Screws
14 x Washers
2 x Side Glass Panels
2 x Main Glass Panels
GL489
Side Glass
GL490 for FPB5
GL491 for FPB7
Front / Top Glass
Three Corner Bracket
Two Corner Bracket
Glass Supports
Fixing screws
omitted for clarity
1) Remove the protective black covers around the FPB, leaving the covers on
the 4 hinge-mounting rivnuts, and fit the 4 glass supports with the
countersunk screws provided.
2) Cut a small piece of insulating tape and place over each countersunk screw
head. This will protect the glass long term.
3) Connect a three-corner bracket to the top inside corner of each side glass,
left hand side detailed overleaf.
NOTE:
Note the position of the dome head screw and shoulder washer in the detail
overleaf and repeat for each bracket connection.
NOTE

IS279 ECN2885 Page 5
4) Connect two-corner brackets to the remaining two holes in each side glass.
5) On a suitable sized work surface, take a main glass panel (for use as the
front panel) and offer it up to one of the side panels.
NOTE:
The main glass panels have offset holes allow this panel to be used as a
front or top glass. Check which way up it locates by placing it alongside a
side glass and confirming which way up the holes match.
6) Connect the front glass to the side glass brackets and repeat for the other
side.
7) Again checking hole alignment first, fit the top glass panel in place.
8) With assistance, lift the glass assembly and place it on the Food Prep Bar,
locating the glass in the support brackets already fitted to the FPB.
GL489
Side Glass
Shoulder Washer
M5 x 8 Dome Head
Slotted Screw
Three Corner Bracket
NOTE

IS279 ECN2885 Page 6
STAINLESS STEEL LID
Pack contents:
1 x Lid
1 x Left Hand Hinge
1 x Right Hand Hinge
4 x M5 x 20 Dome Head Screws
1) Remove the protective black covers from the 4 hinge fixing holes.
2) With 2 of the M5 screws, fit the right hand hinge next to the compressor
cover.
3) With the one of the 2 remaining M5 screws, fit the left hand hinge through
the rear hole only and leave offset, as shown below.
Fix right hand
bracket in place
Fix left hand
bracket in place
with rear screw
only and offset
4) Offer up the lid against the right hand hinge and locate the hinge pins.
5) With the lid in the raised position, square up the left hand hinge until located
on the lid’s hinge pins.
6) Holding the lid in place, fit the left hand hinge’s front screw.
7) Secure the handle to lid using the supplied screws.
8) With both hinges secure, lift the lid by the handle and lower to close.