Lincoln Electric FLEXCUT 200 CE User manual

Operator’s Manual
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
IM10485-A | Issue D ate Jul-22
© Lincoln Global, Inc. All Rights Reserved.
For use with machines having Code Numbers:
12829
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
FlexCut
®
200 CE

THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELECTRIC.
PLEASE EXAMINE CARTON AND EQUIPMENT FOR
DAMAGE IMMEDIATELY
When this equipment is shipped, title passes to the purchaser
upon receipt by the carrier. Consequently, claims for material
damaged in shipment must be made by the purchaser against the
transportation company at the time the shipment is received.
SAFETY DEPENDS ON YOU
Lincoln arc welding and cutting equipment is designed and built
with safety in mind. However, your overall safety can be increased
by proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,
think before you act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed
to avoid minor personal injury or damage to this equipment.
KEEP YOUR HEAD OUT OF THE FUMES.
DON’T get too close to the arc.
Use corrective lenses if necessary
to stay a reasonable distance
away from the arc.
READ and obey the Safety Data
Sheet (SDS) and the warning label
that appears on all containers of
welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to
keep the fumes and gases from
your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away
from your face.
If you develop unusual symptoms, see your supervisor.
Perhaps the welding atmosphere and ventilation system
should be checked.
WEAR CORRECT EYE, EAR &
BODY PROTECTION
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare
with protective screens or barriers.
IN SOME AREAS, protection from noise may be appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area
AT ALL TIMES.
SPECIAL SITUATIONS
DO NOT WELD OR CUT containers or materials which previously
had been in contact with hazardous substances unless they are
properly cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release
highly toxic fumes or gases.
Additional precautionary measures
PROTECT compressed gas cylinders from excessive heat,
mechanical shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an
electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR
IMMEDIATE USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
Safety 01 of 04 - 10/08/2021

SECTION A:
WARNINGS
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Breathing diesel engine exhaust
exposes you to chemicals known to the State
of California to cause cancer and birth defects,
or other reproductive harm.
• Always start and operate the engine in a
well-ventilated area.
• If in an exposed area, vent the exhaust to the outside.
• Do not modify or tamper with the exhaust system.
• Do not idle the engine except as necessary.
For more information go to
www.P65 warnings.ca.gov/diesel
WARNING: This product, when usedfor welding or
cutting, produces fumes or gases which contain
chemicals known to the State ofCalifornia to cause
birth defects and, in some cases, cancer.(California
Health & Safety Code § 25249.5 et seq.)
WARNING: Cancer and Reproductive Harm
www.P65warnings.ca.gov
ARC WELDING CAN BE HAZARDOUS. PROTECT
YOURSELF AND OTHERS FROM POSSIBLE SERIOUS
INJURY OR DEATH. KEEP CHILDREN AWAY.
PACEMAKER WEARERS SHOULD CONSULT WITH
THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For
additional safety information, it is strongly recommended
that you purchase a copy of “Safety in Welding & Cutting -
ANSI Standard Z49.1” from the American Welding Society,
P.O. Box 351040, Miami, Florida 33135 or CSA Standard
W117.2. A Free copy of “Arc Welding Safety” booklet E205
is available from the Lincoln Electric Company, 22801
St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE POWERED
EQUIPMENT.
1.a. Turn the engine off before troubleshooting
and maintenance work unless the
maintenance work requires it to be running.
1.b. Operate engines in open, well-ventilated areas or vent the engine
exhaust fumes outdoors.
arc or when the engine is running. Stop the
engine and allow it to cool before refueling to
prevent spilled fuel from vaporizing on contact
tank. If fuel is spilled, wipe it up and do not start engine until
fumes have been eliminated.
1.d. Keep all equipment safety guards, covers
and devices in position and in good repair.
Keep hands, hair, clothing and tools away
from V-belts, gears, fans and all other
moving parts when starting, operating or
repairing equipment.
1.e. In some cases it may be necessary to remove safety guards to
perform required maintenance. Remove guards only when
necessary and replace them when the maintenance requiring
their removal is complete. Always use the greatest care when
working near moving parts.
1.f. Do not put your hands near the engine fan. Do not attempt to
override the governor or idler by pushing on the throttle control
rods while the engine is running.
1.g. To prevent accidentally starting gasoline engines while turning
the engine or welding generator during maintenance work,
disconnect the spark plug wires, distributor cap or magneto wire
as appropriate.
1.h. To avoid scalding, do not remove the radiator
pressure cap when the engine is hot.
ELECTRIC AND
MAGNETIC FIELDS MAY
BE DANGEROUS
causes localized Electric and Magnetic Fields (EMF).
and welding machines
welders having a pacemaker should consult their physician
before welding.
which are now not known.
2.d. All welders should use the following procedures in order to
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and work
cables. If the electrode cable is on your right side, the
work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as pos-
sible to the area being welded.
2.d.5. Do not work next to welding power source.
SAFETY
Safety 02 of 04 - 10/08/2021
1.c. Do not add the fuel near an open ame welding
with hot engine parts and igniting. Do not spill fuel when lling
2.a. Electric current owing through any conductor
Welding current creates EMF elds around welding cables
2.b. EMF elds may interfere with some pacemakers, and
2.c. Exposure to EMF elds in welding may have other health effects
minimize exposure to EMF elds from the welding circuit:
1.i. Using a generator indoors CAN KILL YOU IN
MINUTES.
1.j. Generator exhaust contains carbon monoxide. This is a poison
you cannot see or smell.
1.k. NEVER use inside a home or garage,
EVEN IF doors and windows are open.
1.l. Only use OUTSIDE and far away from
windows, doors and vents.
1.m. Avoid other generator hazards. READ
MANUAL BEFORE USE.

ELECTRIC SHOCK
CAN KILL.
3.a. The electrode and work (or ground) circuits are
electrically “hot” when the welder is on. Do
not touch these “hot” parts with your bare skin or wet clothing.
Wear dry, hole-free gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full area
of physical contact with work and ground.
In addition to the normal safety precautions, if
welding must be performed under electrically
hazardous conditions (in damp locations or while
wearing wet clothing; on metal structures such as
floors, gratings or scaffolds; when in cramped
positions such as sitting, kneeling or lying, if there
is a high risk of unavoidable or accidental contact
with the workpiece or ground) use the following
equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic welding
gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection should
be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical (earth)
ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of electrode
holders connected to two welders because voltage
between the
two can be the total of the open circuit voltage of both
welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
ARC RAYS CAN BURN.
4.a. Use a shield with the proper filter and cover plates to protect your
eyes from sparks and the rays of the arc when welding or
observing open arc welding. Headshield and filter lens should
conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant material
to protect your skin and that of your helpers from the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES
CAN BE DANGEROUS.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases. When welding, keep your head out of the fume.
Use enough ventilation and/or exhaust at the arc to keep fumes
and gases away from the breathing zone. When welding
hardfacing (see instructions on container or SDS)
or on lead or cadmium plated steel and other
metals or coatings which produce highly toxic
fumes, keep exposure as low as possible and
within applicable OSHA PEL and ACGIH TLV limits
using local exhaust or mechanical ventilation
unless exposure assessments indicate otherwise.
In confined spaces or in some circumstances,
outdoors, a respirator may also be required.
Additional precautions are also required when
welding
on galvanized steel.
5. b. The operation of welding fume control equipment is affected by
various factors including proper use and positioning of the
equipment, maintenance of the equipment and the specific
welding procedure and application involved. Worker exposure
level should be checked upon installation and periodically
thereafter to be certain it is within applicable OSHA PEL and
ACGIH TLV limits.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations. The
heat and rays of the arc can react with solvent vapors to form
phosgene, a highly toxic gas, and other irritating products.
5.d. Shielding gases used for arc welding can displace air and
cause
injury or death. Always use enough ventilation, especially in
confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
Safety Data Sheet (SDS) and follow your employer’s safety
practices. SDS forms are available from your welding
distributor or from the manufacturer.
5.f. Also see item 1.b.
SAFETY
Safety 03 of 04 - 10/08/2021

WELDING AND CUTTING
SPARKS CAN CAUSE
FIRE OR EXPLOSION.
6.a. Remove fire hazards from the welding area. If
this is not possible, cover them to prevent the welding sparks
from starting a fire. Remember that welding sparks and hot
materials from welding can easily go through small cracks and
openings to adjacent areas. Avoid welding near hydraulic lines.
Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site, special
precautions should be used to prevent hazardous situations.
Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)
and the operating information for the equipment being used.
6.c. When not welding, make certain no part of the electrode circuit is
touching the work or ground. Accidental contact can cause
overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances inside.
They can cause an explosion even though they have been
“cleaned”. For information, purchase “Recommended Safe
Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous Substances”,
AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil free
protective garments such as leather gloves, heavy shirt, cuffless
trousers, high shoes and a cap over your hair. Wear ear plugs
when welding out of position or in confined places. Always wear
safety glasses with side shields when in a welding area.
6.g. Connect the work cable to the work as close to the welding area
as practical. Work cables connected to the building framework or
other locations away from the welding area increase the
possibility of the welding current passing through lifting chains,
crane cables or other alternate circuits. This can create fire
hazards or overheat lifting chains or cables until they fail.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “Standard for Fire Prevention During
Welding, Cutting and Other Hot Work”, available from NFPA, 1
Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.
6.j. Do not use a welding power source for pipe thawing.
CYLINDER MAY EXPLODE IF
DAMAGED.
7.a. Use only compressed gas cylinders containing
the correct shielding gas for the process used
and properly operating regulators designed for
the gas and pressure used. All hoses, fittings,
etc. should be suitable for the application and
maintained in good condition.
7.b. Always keep cylinders in an upright position securely chained to
an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected
to physical damage.
• A safe distance from arc welding or cutting operations
and any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand tight
except when the cylinder is in use or connected for use.
7.g. Read and follow the instructions on compressed gas cylinders,
associated equipment, and CGA publication P-l, “Precautions for
Safe Handling of Compressed Gases in Cylinders,” available from
the Compressed Gas Association, 14501 George Carter Way
Chantilly, VA 20151.
FOR ELECTRICALLY
POWERED EQUIPMENT.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National Electrical
Code, all local codes and the manufacturer’s recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Refer to
http://www.lincolnelectric.com/safety
for additional safety information.
SAFETY
Safety 04 of 04 - 10/08/2021

ECO design information 1 ECO design information
ECO design information
The equipment has been designed in order to be compliant with the Directive 2009/125/EC and the Regulation
2019/1784/EU.
Efficiency and idle power consumption:
Name
Efficiency when max power
consumption / Idle power
consumption
Equivalent model
Flexcut 200 CE 92% / 83W (no fan or cooler) No equivalent model
The idle state is defined as the unit is ready to cut, but the output is not enabled. The cool down period after the cut is not
considered the idle state.
The value of efficiency and consumption in idle state have been measured by method and conditions defined in the
product standard EN 60974-1
Manufacturer’s name, product name, code number, product number, serial number and date of production can be read
from rating plate and serial number label.
Typical gas usage for the Flexcut equipment:
The Flexcut 200 CE uses an external Air Compressor, so there are no typical gas flow rates for this product.

ECO design information 2 ECO design information
End of life
At end of life of product, it has to be disposal for recycling in accordance with Directive 2012/19/EU (WEEE), information
about the dismantling of product and Critical Raw Material (CRM) present in the product, can be found at:
www.lincolnelectriceurope.com
Flexcut 200 CE
Item
Component
Material for recovery
CRM
Selective treatment
1
Enclosure and lamination
Steel
-
-
2
Heat sink
Aluminum
Si, 60 g
Mg, 90 g
Ti, 10 g
-
3
Capacitor
-
-
Required
4
External cables – not shown
Copper
-
Required
5
Output terminal, 2 total
Brass and copper
-
-
6
PC board, 12 total
-
-
Required
7
Choke
Transformer
Internal cables
Bus bars
Copper
-
-
8
Enclosure,
Mounting Brackets
Aluminum
Si, 16 g
Mg, 177 g
-
Reference P-1255, code 12829

SAFETY
General Precautions
Whereas plasma cutting has been used safely for years, it does
require certain precautions to ensure the safety of the operator
and other people around the equipment. The following safety
information must be provided to each person who will operate,
observe, perform maintenance, or work in close proximity to this
piece of equipment.
Installation, operation, and repairs made to the system should only
be performed by qualified personnel. The system makes use of
both A.C. and D.C. circuitry for operation. Fatal shock hazard does
exist. Exercise extreme caution while working on the system.
Safety decals On the power supply should not be removed.
ULTRAVIOLET RADIATION
PROTECTION
Plasma cutting produces ultraviolet radiation similar to a welding
arc. This ultraviolet radiation can cause skin and eye burns. For
this reason, it is essential that proper protection be worn. The
eyes are best protected by using safety glasses or a welding
helmet with an AWS No. 12 shade or ISO 4850 No. 13 shade,
which provides protection up to 400 amperes. All exposed skin
areas should be covered with flame-retardant clothing. The
cutting area should also be prepared in such a way that ultraviolet
light does not reflect. Walls and other surfaces should be painted
with dark colors to reduce reflected light. Protective screens or
curtains should be installed to protect additional workers in the
area from ultraviolet radiation.
NOISE PROTECTION
The system generates high noise levels while cutting. Depending
on the size of the cutting area, distance from the cutting torch,
and arc current cutting level, acceptable noise levels may be
exceeded. Proper ear protection should be used as defined by
local or national codes.
TOXIC FUME PREVENTION
Care should be taken to ensure adequate ventilation in the cutting
area. Some materials give off toxic fumes that can be harmful or
fatal to people in the vicinity of the cutting area. Also, some
solvents decompose and form harmful gases when exposed to
ultraviolet radiation. These solvents should be removed from the
area prior to cutting. Galvanized metal can produce harmful gases
during the cutting process. Ensure proper ventilation and use
breathing equipment when cutting these materials.
Certain metals coated with or containing lead, cadmium, zinc,
beryllium, and mercury produce harmful toxins. Do not cut these
metals unless all people subjected to the fumes wear proper air
breathing equipment.
ELECTRIC SHOCK PREVENTION
The system uses high open circuit voltages that can
be fatal. Extreme care should be used when
operating or performing maintenance on the system.
Only qualified personnel should service the system. Observe the
following guidelines to protect against electric shock:
• A wall-mounted disconnect switch should be installed and fused
according to local and national electrical codes. The disconnect
switch should be located as close as possible to the power
supply so it can be turned off in case of an emergency.
• The primary power cord should have a 600 volt minimum rating
in order to protect the operator. In addition, it should be sized
according to local and national electrical codes. Inspect the
primary power cord frequently. Never operate the system if the
power cord is damaged in any way.
• Make sure the primary power ground wire is connected at the
input power ground location on the power supply. Make sure
the connection is securely tightened.
• Make sure the positive output (work ground) of the power
supply is connected to a bare metal area on the cutting table. A
driven ground rod should be placed no further than five feet
from this connection. Make sure this ground point on the cutting
table is used as the star ground point for all other ground
connections.
• Inspect the torch leads frequently. Never use the system if the
leads are damaged in any way.
• Do not stand in wet, damp areas when operating or performing
maintenance on the system.
• Wear insulated gloves and shoes while operating or performing
maintenance on the system.
• Make sure the system is switched off at the wall disconnect
before servicing the power supply or torch.
• Never change torch consumable parts unless main power to the
system is switched off at the power supply or wall disconnect.
• Do not attempt to remove any parts from beneath the torch
when cutting. Remember that the workpiece forms the current
path back to the power supply.
• Never bypass the safety interlock devices.
• Before removing any of the covers, switch the system off at the
wall disconnect. Wait at least five (5) minutes before removing
any cover. This will give the capacitors inside the unit time to
discharge. See Section 5 for additional safety precautions.
• Never operate the system without all of the covers in place. See
Section 5 for additional safety precautions.
• Preventive maintenance should be performed daily to avoid
possible safety hazards.
2
FlexCut®200 CE SAFETY

3
FlexCut®200 CE
FIRE PREVENTION
When using the system , it is necessary to exercise good
judgment. While cutting, the arc produces sparks that could cause
a fire if they fall on flammable materials. Make sure that all
flammable materials are a suitable distance away from the cutting
area. All flammable liquids should be at least 40 feet away from
the cutting area, preferably stored in a metal cabinet. Plasma
cutting should never be attempted on containers that contain
flammable materials. Make sure that fire extinguishers are readily
accessible in the cutting area.
EXPLOSION PREVENTION
The system uses compressed gases. Use proper
techniques when handling compressed gas cylinders and other
compressed gas equipment. Observe the following guidelines to
protect against explosion:
• Never operate the system in the presence of explosive gases
or other explosive materials.
• Never cut pressurized cylinders or any closed container.
• When using a water table and cutting aluminum under water
or with water touching the underside at the aluminum plate,
hydrogen gas is produced. This hydrogen gas may collect
under the plate and explode during the cutting process. Make
sure the water table is properly aerated to help prevent the
accumulation of hydrogen gas.
• Handle all gas cylinders in accordance with safety standards
published by the U.S. Compressed Gas Association (CGA),
American Welding Society (AWS), Canadian Standards
Association (CSA), or other local or national codes.
• Compressed gas cylinders should be maintained properly.
Never attempt to use a cylinder that is leaking, cracked, or
has other signs of physical damage.
• All gas cylinders should be secured to a wall or rack to
prevent accidental knock over.
• If a compressed gas cylinder is not being used, replace the
protective valve cover.
• Never attempt to repair compressed gas cylinders.
• Keep compressed gas cylinders away from intense heat,
sparks, or flames.
• Clear the compressed gas cylinder connection point by
opening the valve momentarily prior to installing a regulator.
• Never lubricate compressed gas cylinder valves or pressure
regulators with any type of oil or grease.
• Never use a compressed gas cylinder or pressure regulator
for any purpose other than which it is intended.
• Never use a pressure regulator for any gas other than which it
is intended.
• Never use a pressure regulator that is leaking or has other
signs of physical damage.
• Never use any gas hose that is leaking or has other signs of
physical damage.
HEALTH SUPPORT EQUIPMENT
The system creates electric and magnetic fields
that may interfere with certain types of health
support equipment, such as pacemakers. Any person who uses a
pacemaker or similar item should consult a doctor before
operating, observing, maintaining, or servicing the system.
Observe the following guidelines to minimize exposure to these
electric and magnetic fields:
• Stay as far away from the~power supply, torch, and torch
leads as possible.
• Route the torch leads as close as possible to the work ground
cable.
• Never place your body between the torch leads and work
ground cable. Keep the work ground cable and the torch
leads on the same side of your body.
• Never stand in the center of a coiled up set of torch leads or
work ground cable.
SAFETY

FlexCut®200 CE
Safety Standards Booklet Index
For further information concerning safety practices to be exercised
with plasma arc cutting equipment, please refer to the following
publications:
1. AWS Standard AWN, Arc Welding and Cutting Noise, obtainable
from the American Welding Society, 550 NW LeJeune Road,
Miami, FL 33126.
2. AWS Standard C5.2, Recommended Practices for Plasma Arc
Cutting, obtainable from the American Welding Society, 550 NW
LeJeune Road, Miami, FL 33126.
3. AWS Standard FSW, Fire Safety in Welding and Cutting,
obtainable from the American Welding Society, 550 NW
LeJeune Road, Miami, FL 33126.
4. AWS Standard F4.1, Recommended Safe Practices for
Preparation for Welding and Cutting of Containers and Piping,
obtainable from the American Welding Society, 550 NW
LeJeune Road, Miami, FL 33126.
5. AWS Standard ULR, Ultraviolet Reflectance of Paint, obtainable
from the American Welding Society, 550 NW LeJeune Road,
Miami, FL 33126.
6. AWS I ANSI Standard Z49.1, Safety in Welding, Cutting, and
Allied Processes, obtainable from the American Welding
Society, 550 NW LeJeune Road, Miami, FL 33126.
7. ANSI Standard Z41.1 , Standard For Men's Safety-Toe
Footwear, obtainable from the American National Standards
Institute, 11 West 42nd Street, New York, NY 10036.
8. ANSI Standard Z49.2, Fire Prevention in the Use of Cutting and
Welding Processes, obtainable from the American National
Standards Institute, 11 West 42nd Street, New York, NY 10036.
9. ANSI Standard Z87.1, Safe Practices For Occupation and
Educational Eye and Face Protection, obtainable from the
American National Standards Institute, 11 West 42nd Street,
New York, NY 10036.
10. ANSI Standard Z88.2, Respiratory Protection, obtainable from
the American National Standards Institute, 11 West 42nd
Street, New York, NY 10036.
11. OSHA Standard 29CFR 1910.252, Safety and Health
Standards, obtainable. from the U.S. Government Printing
Office, Washington, D.C. 20402.
12. NFPA Standard 51 , Oxygen - Fuel Gas Systems for Welding,
Cutting, and Allied Processes, obtainable from the National
Fire Protection Association, 1 Batterymarch Park, Quincy, MA
02269.
13. NFPA Standard 51 B, Cutting and Welding Processes,
obtainable from the National Fire Protection Association, 1
Batterymarch Park, Quincy, MA 02269.
14. NFPA Standard 70, National Electrical Code, obtainable from
the National Fire Protection Association, 1 Batterymarch Park,
Quincy, MA 02269.
15. CGA booklet P-1 , Safe Handling of Compressed Gases in
Containers, obtainable from the Compressed Gas Association,
1725 Jefferson Davis Highway, Suite 1004, Arlington, VA
22202.
16. CGA booklet P-14, Accident Prevention in Oxygen-Rich and
Oxygen-Deficient Atmospheres, obtainable from the
Compressed Gas Association, 1725 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202.
17. CGA booklet TB-3, Hose Line Flashback Arrestors, obtainable
from the Compressed Gas Association, 1725 Jefferson Davis
Highway, Suite 1004, Arlington, VA 22202.
18. CSA Standard W117 .2, Safety in Welding, Cutting, and Allied
Processes, obtainable from Canadian Standards Association,
178 Rexdale Boulevard, Toronto, Ontario M9W IR3, Canada.
19. Canadian Electrical Code Part 1, Safety Standard for Electrical
Installations, obtainable from the Canadian Standards
Association, 178 Rexdale Boulevard, Toronto, Ontario M9W 1
R3, Canada.
4
SAFETY