Linear Technology DC1084A-B User manual

1
dc1084a-bf
DEMO MANUAL DC1084A-B
DESCRIPTION
LTM4602HV
28V, 6A Step-Down
µModule Regulator
DemonstrationcircuitDC1084A-BfeaturestheLTM
®
4602HV,
the high efficiency, high density step-down μModule
®
regulator. The input voltage range is from 4.5V to 28V.
The output voltage is jumper programmable from 0.6V to
5V, refer to the step-down ratio curve in the LTM4602HV
data sheet. The rated load current is 6A, while derating is
necessary for certain VIN, VOUT and thermal conditions. L, LT, LTC, LTM, μModule, Linear Technology and the Linear logo are registered trademarks of
Linear Technology Corporation. All other trademarks are the property of their respective owners.
BOARD PHOTO
The LTM4602HV data sheet must be read in conjunction
with this demo manual prior to working on or modifying
demo circuit DC1084A-B.
Design files for this circuit board are available at
http://www.linear.com/demo
PERFORMANCE SUMMARY
(TA= 25°C)
PARAMETER CONDITION VALUE
Input Voltage Range 4.5V to 28V
Output Voltage VOUT Jumper Selectable (Open for 0.6V) 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V
Maximum Continuous Output Current Derating is Necessary for Certain VIN, VOUT and
Thermal Conditions
6A DC
Default Operating Frequency 800kHz

2
dc1084a-bf
DEMO MANUAL DC1084A-B
QUICK START PROCEDURE
Figure 1. Test Setup of DC1084A-B (EXTVCC Bias Supply is Optional)
Demonstration circuit DC1084A-B is an easy way to evalu-
ate the performance of the LTM4602HVEV. Please refer to
Figure 1 for proper measurement equipment setup and
follow the procedure below:
1. Place jumpers in the following positions for a typical
1.5VOUT application:
FCB RUN/SS VOUT SEL
CCM ON 1.5V
2. With power off, preset the load to 0A and VIN supply
to be less than 28V. Connect the input power supply,
load, optional 5V bias supply and meters as shown
in Figure1. The optional 5V bias supply must be off
anytime the supply to VIN is turned off.
3. Turn on the power at the input. The output voltage
should be 1.5V ±2%.
4. Once the proper output voltage is established, adjust
the load within the operating range and observe the
output voltage regulation, ripple voltage, efficiency and
other parameters. Output ripple should be measured at
J6 with a BNC cable.
5. For optional load transient test, apply adjustable pulse
signal between IOSTEP CLK and GND pins. Pulse am-
plitude sets the current step. The pulse signal should
have very small duty cycle (<15%) to limit the thermal
stress on the transient load circuit. The output tran-
sient current can be monitored at BNC connector J5
(10mV/A).

3
dc1084a-bf
DEMO MANUAL DC1084A-B
QUICK START PROCEDURE
Figure 2. Measured Supply Efficiency with Different VIN and VOUT
Figure 3. Measured Load Transient Response (0A-5A Step)
VIN = 12V, VOUT = 1.5V
0A to 5A LOAD STEP
FCB = 0V
COUT = 1 ×22μF CERAMIC (1206), 1 ×100μF CERAMIC (1812),
C3 = 100pF

4
dc1084a-bf
DEMO MANUAL DC1084A-B
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 1 C1 CAP, 150μF 20% 35V ALUM SANYO 35MV150WXV (Now SUNCON 35MV150WXV)
2 2 C5, C2 CAP, 1206 10μF 20% 35V X5R TAIYO YUDEN GMK316 BJ106ML-T
3 1 C10 CAP, 1206 22μF 20% 6.3V X5R AVX 12066D266MAT2A
4 1 C7 CAP, 1812 100μF 20% 6.3V X5R TDK C4532X5R0J107MZ
5 1 C12 CAP, 0603 100pF 10% 50V X7R AVX 06035C101KAT1A
6 1 R2 RES, 0603 66.5k 1% 1/10W AAC CR16-6652FM
7 1 R8 RES, 0603 0Ω JUMPER ACC CJ06-000M
8 1 U1 IC, LTM4602HVEV LINEAR TECH. LTM4602HVEV
Additional Demo Board Circuit Components
1 0 C4, C3 CAP, 1206 OPTION TAIYO YUDEN EMK316BJ475ML-T OPTION
2 0 C8 CAP, 1812 100μF 20% 6.3V X5R OPTION TDK C4532X5R0J107MZ OPTION
3 0 C6 CAP, 1812 OPTION TAIYO YUDEN JMK432BJ107MU-T OPTION
4 0 C11, C14, C18, C19 CAP, 0603 OPTION OPTION
5 1 C13 CAP, 0603 100pF 10% 50V NPO AVX 06035A101KAT
6 2 C15,C16 CAP, 0603 1μF 20% 10V X5R TAIYO YUDEN LMK107BJ105MA-T
7 0 C17 CAP, 0805 1μF 20% 16V X5R OPTION TAIYO YUDEN EMK212BJ105MG-T OPTION
8 1 D1 DIODE, ZENER 4.7V DIODES INC. BZX84C4V7
9 1 Q14 XSTR, SUD50N03-10CP MOSFET SILICONIX SUD50N03-10CP
10 1 R1 RES, 0603 49.9k 1% 1/10W AAC CR16-4992FM
11 1 R3 RES, 0603 31.6k 1% 1/10W AAC CR16-3162FM
12 1 R4 RES, 0603 22.1k 1% 1/10W AAC CR16-2212FM
13 1 R5 RES, 0603 13.7k 1% 1/10W AAC CR16-1372FM
14 3 R6, R10, R12 RES, 0603 10k 5% 1/10W VISHAY CRCE060310K0JNEA
15 1 R7 RES, 0603 5.1k 5% 1/10W AAC CR16-512JM
16 1 R9 RES, 0603 1M 5% 1/16W AAC CR16-105JM
17 1 R11 RES, 2512 0.01Ω 5% 1W IRC LRF2512-01-R010-J
18 0 R13 RES, 0603 OPTION OPTION
19 1 R14 RES, 0603 100k 1% 1/10W AAC CR16-1003FM

5
dc1084a-bf
DEMO MANUAL DC1084A-B
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SCHEMATIC DIAGRAM

6
dc1084a-bf
DEMO MANUAL DC1084A-B
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
[phone] ●FAX: [phone] ●www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2011
LT 0911 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica-
tion engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Power Management IC Development Tools category:
Click to view products by Analog Devices manufacturer:
Other Similar products are found below :
EVAL-ADM1168LQEBZ EVB-EP5348UI MIC23451-AAAYFL EV MIC5281YMME EV DA9063-EVAL ADP122-3.3-EVALZ ADP130-
0.8-EVALZ ADP130-1.2-EVALZ ADP130-1.5-EVALZ ADP130-1.8-EVALZ ADP1714-3.3-EVALZ ADP1716-2.5-EVALZ ADP1740-1.5-
EVALZ ADP1752-1.5-EVALZ ADP1828LC-EVALZ ADP1870-0.3-EVALZ ADP1871-0.6-EVALZ ADP1873-0.6-EVALZ ADP1874-0.3-
EVALZ ADP1882-1.0-EVALZ ADP199CB-EVALZ ADP2102-1.25-EVALZ ADP2102-1.875EVALZ ADP2102-1.8-EVALZ ADP2102-2-
EVALZ ADP2102-3-EVALZ ADP2102-4-EVALZ ADP2106-1.8-EVALZ ADP2147CB-110EVALZ AS3606-DB BQ24010EVM
BQ24075TEVM BQ24155EVM BQ24157EVM-697 BQ24160EVM-742 BQ24296MEVM-655 BQ25010EVM BQ3055EVM
NCV891330PD50GEVB ISLUSBI2CKIT1Z LM2744EVAL LM2854EVAL LM3658SD-AEV/NOPB LM3658SDEV/NOPB LM3691TL-
1.8EV/NOPB LM4510SDEV/NOPB LM5033SD-EVAL LP38512TS-1.8EV EVAL-ADM1186-1MBZ EVAL-ADM1186-2MBZ