Linear Technology Sys-Pro 114460 User manual

114460 | Sys-Pro Push/Radio Mesh Dimmer with 0/1-10V Output and
Switch 85-265V 1.5A
Output current
Max 1.5A (AC)
Input voltage AC85-265V
Output voltage AC85-265V
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Dimming data
Dimming range
RF 2.4GHz + Push Dim
30m
256 levels
0 -100%
Technical Parameters
Input and Output
Safety and EMC
EMC standard (EMC)
EN 55015:2013
EN 61547:2009
EN 61000-3-2:2014
EN 61000-3-3:2013
Certification CE,EMC,LVD
EN 61347-2-11:2002
EN 61347-1:2015
EN 62493:2015
Safety standard(LVD)
Warranty
5 years
Warranty
Input signal
RF Control distance
Dimming level
Ta: -30
O
C ~ +55
O
C
Tc: +85
O
C
Model No.: L1
Features
0/1-10V RF + Push Dimmer
LVD
●0/1-10V RF or AC push dimmer, 1 channel output.
●Output 1 channel 0/1-10V signal, connect with 0/1-10V dimmable driver.
●High voltage AC input, High voltage AC relay output.
●0-10V or 1-10V output selectable by DIP switch.
●256 levels 0-100% dimming smoothly without any flash.
●Compatibility with 2.4G single zone or multiple zone dimming remote control.
●Connect with external push switch to achieve on/off and 0-100% dimming
function.
●Easy to be placed in standard wall junction box behind a push switch.
Output signal 0/1-10V (20mA)
User Manual Ver 1.0.2 Page 1
www.iskydance.com

114460 | Sys-Pro Push/Radio Mesh Dimmer with 0/1-10V Output and
Switch 85-265V 1.5A
Mechanical Structures and Installations
L1 0/1-10V RF + Push Dimmer
AC L input
AC N input
AC N output
AC L output
Wiring diagram
●L1 connect with 0/1-10V dimming driver (no use AC OUT)
V+
V-
DIM+
DIM-
ACN
ACL
+
Single color LED strip
AC110-220V
0/1-10V
Dimmable Driver
L1
RoHS
N L
0/1-10V RF Dimmer
0/1-10V OUT
-
AC IN
L1 N1
AC OUT
+
0.5-2.0mm²
4-5mm
MATCH
ON 0-10V
1-10V
Uin=85-265VAC
Out=0/1-10V(20mA)
AC Out=Max1.5A
Temp Range: -30℃~ +55℃
P
Push
Match key
AC Push in
52.00 mm
52.00 mm
26.00 mm
Typical Wall Junction Box Mounting
0-10V signal output
GND
DIP switch for
0-10V or 1-10V
select
L1
RoHS
N L
0/1-10V RF Dimmer
0/1-10V OUT
-
AC IN
L1 N1
AC OUT
+
0.5-2.0mm²
4-5mm
MATCH
ON 0-10V
1-10V
Uin=85-265VAC
Out=0/1-10V(20mA)
AC Out=Max1.5A
Temp Range: -30℃~ +55℃
P
Push
Push Switch
User Manual Ver 1.0.2 Page 2
www.iskydance.com

114460 | Sys-Pro Push/Radio Mesh Dimmer with 0/1-10V Output and
Switch 85-265V 1.5A
V+
V-
DIM+
DIM-
ACN
ACL
+
Single color LED strip
AC110-220V
0/1-10V
Dimmable Driver
RoHS
N L
0/1-10V RF Dimmer
0/1-10V OUT
-
AC IN
L1 N1
AC OUT
+
0.5-2.0mm²
4-5mm
MATCH
ON 0-10V
1-10V
Uin=85-265VAC
Out=0/1-10V(20mA)
AC Out=Max1.5A
Temp Range: -30℃~ +55℃
P
Push
Push Switch
Use Power Restart
Match:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone
remote)
or zone key (multiple zone remote) 3 times on the
remote. The light blinks 3 times means match is
successful.
.Delete:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone
remote) or zone key (multiple zone remote) 5 times
on the remote. The light blinks 5 times means all
matched remotes were deleted.
Use the controller’s Match key
Match:
Short press match key, immediately press on/
off key (single zone remote) or zone key
(multiple zone remote) of the remote.
Delete:
Press and hold match key for 5s to delete all
match, The light blinks 5 times means all
matched remotes were deleted.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
1-10V Dimmer
2-10V Dimmer
Note: We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces, The
maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
0-10V or 1-10V dimming setting
Select 0-10V dimmer or 1-10V dimmer according to dimmable LED driver.
ON 0-10V
1-10V
User Manual Ver 1.0.2 Page 3
www.iskydance.com

Causes
1. The battery has no power.
2. Beyond controllable distance.
3. The controller did not match the remote.
1. No power.
2. Wrong connection or insecure.
Malfunctions
No response
from the remote
No light
Malfunctions analysis & troubleshooting
Troubleshooting
1. Replace battery.
2. Reduce remote distance.
3. Re-match the remote.
1. Check the power.
2. Check the connection.
Push Dim Function
●Short press:
Turn on or off light.
●Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes to the opposite direction.
●Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.
114460 | Sys-Pro Push/Radio Mesh Dimmer with 0/1-10V Output and
Switch 85-265V 1.5A
Application notes
1. All the receivers in the same zone.
Zone 1 Zone 2 Zone 3
30m 30m
Zone 4
RF remote
RF remote
Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m,
as long as there is a receiver within 30m, the remote control distance can be limitless.
Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled
by the same remote.
Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce
the range. Strong signal sources such as WiFi routers and microwave ovens will affect the range.
We recommend for indoor applications that receiver placements should be no further apart than15m.
2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.
30m
30m
30m
User Manual Ver 1.0.2 Page 4
www.iskydance.com