Linear eMerge Essential User manual

eMerge Essential Access Control System
Document Number: 620-100239, Rev. C
Installation Guide
Linear LLC
1950 Camino Vida Roble, Suite 150
Carlsbad, CA 92008-6517
www.linearcorp.com
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,E3,INSTALLATION GUIDE - LINEAR P/N: 620-100239 C - INK: 4/C PROCESS - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - FOLDING: ALBUM FOLD - BINDING: SADDLE STITCH - SCALE: 1-1

2
Notices
All rights strictly reserved. No part of this document may be reproduced, copied, adapted, or
transmitted in any form or by any means without written permission from Linear LLC.
Standards Approvals
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Corporate Office
Linear LLC
1950 Camino Vida Roble, Suite 150
Carlsbad, CA 92008-6517
Tel: [phone]
Fax: [phone]
Technical Support
Tel: [phone]
Hours: 5:00 AM to 4:30 PM Pacific Time, Monday - Friday

3
Contents
1.0 Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Access Control Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
eMerge Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Installation Overview Checklist � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
2.0 Control Panel Layout � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Control Panel Components � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
3.0 Installing the Control Panel � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
Mounting the eMerge Essential Panel � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
Mounting the eMerge Essential Plus Panel � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
4.0 System Power � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
eMerge Essential Power Connection � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
eMerge Essential Plus Power Connection� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �11
PoE Connection � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �12
5.0 Inputs and Outputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �13
System Inputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �13
Wiring the Inputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �14
System Outputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �15
Door Lock Outputs � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �15
6.0 Readers� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �17
Wiring the Readers� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �17
7.0 Network Connection � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �18
Preparing for the Network � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �18
Connecting to the Network � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �19
8.0 Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �20

www.linearcorp.com 4 eMerge Essential Installation Manual
1.0 Introduction
is manual contains information regarding the basic installation, wiring and conguration of
the eMerge Essential and eMerge Essential Plus access control systems. e eMerge Essential
is enclosed in a space-ecient and durable plastic housing. e eMerge Essential Plus is enclosed
in a heavy-duty steel cabinet and features a self-contained battery back-up with a supervised
power supply. Both systems use the same control panel layout and system wiring.
Access Control Overview
Access control systems are designed to monitor and control access throughout a building or restricted
area. An access control system involves the use of an access device (card, PIN code, etc.), which is pre-
sented at an entry device (reader/keypad) to gain access. When access is granted, a door is unlocked
for a pre-programmed amount of time and a transaction is recorded in a database for reporting or
tracking purposes.
eMerge Overview
e eMerge Essential provides a browser-based one door, two reader access control system with
immediate expansion capability to four doors, eight readers via an optional software license (P/N
ES-1DL or ES-1DLB w/reader). e eMerge Essential includes Ethernet support, an integrated
web server and Power over Ethernet (PoE) support. Designed with eciency in mind, the system
is ideal for smaller commercial, industrial, banking, retail and restaurant access management ap-
plications; while oering scalability for growth.
Specifications
Processor Cortex 1GHz
On-board RAM 512MB DDR2 (333MHz)
Storage 4 GB Micro SD
PIP 12VDC 60W UL Approved
Operating system Embedded Linux
Simultaneous system users 8
Transactions per second > 30
Plastic enclosure (W x H x D): 12.25 in x 11.1 in x 2.23 in
31.1 cm x 28.2 cm x 5.7 cm
Steel enclosure (W x H x D) 17.5 in x 24.25 in x 6.4 in
44.5 cm x 61.6 cm x 16.25 cm
Temperature specification -20°F to 130°F (-28°C to 54°C)
Doors/Portals 1 (scalable to 4)
Maximum readers 8
Inputs 12
Outputs 8
Card holders (users) 1,000
Access cards 8,000
Cards per person 12
Card formats 32
Access levels 8
Time Schedules 100
Online transactions 15,000

www.linearcorp.com 5 eMerge Essential Installation Manual
Installation Overview Checklist
e following list presents the steps required for successfully installing an eMerge Essential system.
❒Mount the control panel
❒Connect power to the panel
❒Connect the readers
❒Wire the inputs and outputs
❒Obtain IP address and other TCP/IP information from network administrator
❒Congure the eMerge Essential’s network settings
❒(Optional) Add licenses for additional doors and readers
❒Connect the eMerge to a local area network (LAN)
Note: The checklist pro-
vides a logical sequence
for installing an eMerge
system; however, it is not
necessary to follow this
specic order.

www.linearcorp.com 6 eMerge Essential Installation Manual
2.0 Control Panel Layout
Control Panel Components
e following illustration shows the eMerge control panel wiring and components.
DOOR 1
LOCK
IN READER 1OUT READER 1
DOOR 1 CONTACTREX 1
DOOR 2
LOCK
IN READER 2OUT READER 2
AUX RELAY 4
AUX RELAY 3
AUX RELAY 2
AUX RELAY 1
AUX INPUT 4
AUX INPUT 3
AUX INPUT 2
AUX INPUT 1
+12VDC / 5A
(100-240 VAC)
TAMPER
DOOR 3
LOCK
IN READER 3
OUT READER 3 REX 3
DOOR 3
CONTACT
REX 4
DOOR 4
CONTACT
DOOR 4
LOCK
IN READER 4
OUT READER 4
+12V LED D0 D1 GND INPUT GND INPUT GND +12V LED D0 D1 GND NC C NO +12V LED D0 D1 GND INPUT GND INPUT GND +12V LED D0 D1 GND NC C NO
AUX IN 3
GND
AUX IN 4
GND
AUX IN 1
GND
AUX IN 2
GND
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
+12V LED D0 D1 GND +12V LED D0 D1 GND INPUT GND INPUT GND NC C NO +12V LED D0 D1 GND +12V LED Buzzer D0 D1 GND INPUT GND INPUT GND NC C NO
DOOR 1DOOR 2
DOOR 3DOOR 4
DOOR 2 CONTACTREX 2
ETHERNET
TMP -
TMP +
FLT -
FLT +
GND
12VDC
PWR FAULT
SD CARD
SLOT
RESET
LED BANK
LAN LED
DL8
DL7
DL6
DL5
DL4
DL3
DL2
DL1
DL17
DL16
DL15
DL14
DL13
DL12
DL11
DL10
DL9
DL19
DL18
JP1
S2
S1
External
+12VDC
POE
(Default)
JP1 - Power Input
EARTH
GROUND
LEAD
Figure 2.1. eMerge Board Layout
Table 2.1: LED Indicators Table 2.2: Default I/O States
LED Condition
DL17 Red On = Power On Bottom Board
DL9 Red On = Power On Middle Board
DL1 Blue On = System is Rebooted
DL1 to DL16 Blue On = System is Booting
DL19, DL 18 Blue Blink = Network Connection
NOTE: Boot up time is approx. 60 secs.
Attribute Default State
Door Status Inputs Normally Open, Unsupervised, 8 Sec. Held OpenTime
REX Inputs Normally Open, Momentary, Unsupervised
Auxiliary Inputs Normally Open, Unsupervised
Door Lock Outputs Not Energized, Single Pulse, 3 Second Unlock Time
Aux Outputs Not Energized, Single Pulse, 3 Seconds On

www.linearcorp.com 7 eMerge Essential Installation Manual
3.0 Installing the Control Panel
Mounting the eMerge Essential Panel
e eMerge Essential housing is designed to accommodate the necessary wiring connections for
most installations. Knock-outs are provided at the back-plate of the housing. e enclosure should
be mounted in a secure location within normal temperature and humidity levels.
Installing the Panel
1. Run all necessary wires to the panel location.
2. Remove the enclosure’s cover by removing the two screws in the front of the housing.
3. Level the enclosure on a sturdy wall. Mark the mounting holes with a pencil.
4. Partially insert screws into the top two mounting holes and hang the enclosure on the screws.
5. Pull all wires through the knock-out holes in the enclosure. Label each wire according to its use.
6. Recheck for levelness, insert the two lower screws, and tighten all four mounting screws.
+12V LED D0 D1 GND INPUT GND INPUT GND +12V LED D0 D1 GND NC C NO +12V LED D0 D1 GND INPUT GND INPUT GND +12V LED D0 D1 GND NC C NO
AUX IN 2
GND
AUX IN 1
GND
AUX IN 4
GND
AUX IN 3
GND
NC
C
NO
NC
C
NO
AUX
RLY 4
AUX
RLY 3
NC
C
NO
NC
C
NO
+12V LED D0 D1 GND +12V LED D0 D1 GND INPUT GND INPUT GND NC C NO +12V LED D0 D1 GND +12V LED D0 D1 GND INPUT GND INPUT GND NC C NO
DOOR 1DOOR 2
DOOR 3DOOR 4
ETHERNET
TMP -
TMP +
FLT -
FLT +
GND
12VDC
AUX
RLY 2
AUX
RLY 1
Enclosure Knockouts
Cover Screw
Cover Screw
Bottom Mounting Holes
Enclosure Knockouts
Mounting Hole
Cover
Tamper
EARTH
GROUND
LEAD
Figure 3.1. eMerge Essential Enclosure
Note: Choose a centrally
located, clean and dry
area near an AC power
source. Avoid mounting
the panel within 6 feet
of any equipment that
generates electrical
interference.
Caution: This equipment
includes electronic com-
ponents that are highly
sensitive to static electric-
ity. Please discharge by
touching a ground before
installing or handling this
equipment.
Note: This device com-
plies with Part 15 of the
FCC Rules. Operation is
subject to the following
two conditions: (1) this
device may not cause
harmful interference,
and (2) this device must
accept any interference
received, including inter-
ference that may cause
undesired operation.

www.linearcorp.com 8 eMerge Essential Installation Manual
Mounting the eMerge Essential Plus Panel
e eMerge Essential Plus enclosure is designed to accommodate two 12VDC 7Ah backup batter-
ies and the necessary wiring connections for most installations. Conduit knock-outs are provided
on all sides of the enclosure. e enclosure should be mounted in a secure location within normal
temperature levels. A minimum of 12 inches of space around all sides of the enclosure is recom-
mended.
Installing the eMerge Essential Plus
1. Run all necessary wires to the panel location.
2. Remove the enclosure’s cover by removing the front of the housing.
3. Remove the metal cabinet knock-outs required for wire entry.
4. Level the enclosure on a sturdy wall. Mark the mounting holes with a pencil. (e cabinet
can be vertically or horizontally mounted depending on space requirements.)
5. Partially insert screws into the top two mounting holes and hang the enclosure on the screws.
6. Pull all wires through the knock-out holes in the enclosure. Label each wire according to its use.
7. Recheck for levelness, insert the two lower screws, and tighten all four mounting screws.
DOOR 1DOOR 2
DOOR 3DOOR 4
Tie wrap holders
Mounting holes
Cabinet knockouts
Power Supervision
Module
Cover Tamper
Figure 3.2. eMerge Essential Plus Enclosure
Note: Choose a centrally
located, clean and dry
area near an AC power
source. Avoid mounting
the panel within 6 feet
of any equipment that
generates electrical
interference.
Caution: This equipment
includes electronic com-
ponents that are highly
sensitive to static electric-
ity. Please discharge by
touching a ground before
installing or handling this
equipment.

www.linearcorp.com 9 eMerge Essential Installation Manual
4.0 System Power
e eMerge Essential is powered using a 12VDC / 5A plug-in-power supply (Linear P/N
PIP-12VUR, not included). For UL listed installations, please use Linear P/N PIP-12V60W.
e control panel may also be powered using an optional Power over Ethernet (PoE) injector
(requires Linear PoE module, P/N 620-100159).
eMerge Essential Power Connection
Power Supply Connection
1. Connect terminal 1 from the plug-in-power supply (PIP) to pin 1 (+12VDC) on the panel.
2. Connect terminal 3 from the PIP to pin 2 (GND) on the panel.
3. Connect terminal 2 to the green earth ground lead provided in the enclosure.
4. Plug the PIP into a dedicated receptacle that is not controlled by a switch.
5. e PWR LED on the panel will illuminate to indicate that power is present.
AUX RELAY 4
AUX RELAY 3
AUX RELAY 2
AUX RELAY 1
AUX INPUT 4
AUX INPUT 3
AUX INPUT 2
AUX INPUT 1
INPUT GND INPUT GND
+12V LED Buzzer D0 D1 GND
NC C NO +12V LED Buzzer D0 D1 GND INPUT GND INPUT GND +12V LED Buzzer D0 D1 GND NC C NO
AUX IN 2
GND
AUX IN 1
GND
AUX IN 4
GND
AUX IN 3
GND
NC
C
NO
NC
C
NO
AUX
RLY 4
AUX
RLY 3
NC
C
NO
NC
C
NO
+12V LED Buzzer D0 D1 GND +12V LED Buzzer D0 D1 GND INPUT GND INPUT GND NC C NO +12V LED Buzzer D0 D1 GND
INPUT GND INPUT GND
NC C NO
DOOR 1DOOR 2
DOOR 3DOOR 4
AUX
RLY 2
AUX
RLY 1
Enclosure Knockouts
Screw for cover
Enclosure Knockouts
Top Mounting Hole
TMP -
TMP +
FLT -
FLT +
GND
12VDC
12VDC Earth GND
GND
1 2 3
+12VDC PIP
(100-240VAC)
12VDC Earth GND
GND
1 2 3 4
+12VDC PIP
P/N PIP-12V60W
EARTH
GROUND
LEAD
Figure 4.1. Power Connection
Note: The eMerge Es-
sential housing will not
accommodate a backup
battery. If using a backup
battery, a separate hous-
ing must be installed.
Caution: Improper power
wiring will damage the
fuse and void the war-
ranty.
Cable Specications for
PIP: 14 AWG Belden (2
conductor) or equivalent.
Maximum distance: 10
feet (3 meters).
Note: Power should only
be applied to the system
when all connections are
secured and tested.

www.linearcorp.com 10 eMerge Essential Installation Manual
Power Fault Connection
e controller is equipped with a power fault input that can be utilized as follows:
1. Determine whether your power fault input device uses a normally closed or normally open
conguration. Please refer to instructions provided by the manufacturer.
2. Connect the power fault input device to PIN 3 and PIN 4 on the terminal strip.
3. Apply power and verify that the power fault input device is functioning properly.
PIN 6
PIN 5
PIN 4
PIN 3
PIN 2
PIN 1
EMERGE ESSENTIAL CONTROL PANEL
6-pin terminal block
AUX RELAY 4
AUX RELAY 3
AUX RELAY 2
AUX RELAY 1
AUX INPUT 4
AUX INPUT 3
AUX INPUT 2
AUX INPUT 1
INPUT GND INPUT GND
+12V LED Buzzer D0 D1 GND
NC C NO
+12V LED Buzzer D0 D1 GND INPUT GND INPUT GND +12V LED Buzzer D0 D1 GND
NC C NO
AUX IN 2
GND
AUX IN 1
GND
AUX IN 4
GND
AUX IN 3
GND
NC
C
NO
NC
C
NO
AUX
RLY 4
AUX
RLY 3
NC
C
NO
NC
C
NO
+12V LED Buzzer D0 D1 GND +12V LED Buzzer D0 D1 GND INPUT GND INPUT GND NC C NO
+12V LED Buzzer D0 D1 GND +12V LED Buzzer D0 D1 GND INPUT GND INPUT GND NC C NO
DOOR 1
DOOR 2
DOOR 3
DOOR 4
TMP -
TMP +
FLT -
FLT +
GND
12VDC
AUX
RLY 2
AUX
RLY 1
Enclosure Knockouts
Screw for cover
Enclosure Knockouts
Top Mounting Hole
Top Mounting Hole
Power Fault Input
Figure 4.2. eMerge Essential Power Fault Connection