➏GD00Z-3 MOUNTING ➐GD00Z-3 CONNECTIONS ➑SYSTEM OPERATION
➒OPERATION NOTES
1. The warning light will flash and the warning beeper will sound for five seconds
before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR
OPENER.THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the GD00Z-3
will allowuser to try to operate the door one more time. If the second attempt fails,
the GD00Z-3 will go into lock-out mode. See Note #3.
3. If the GD00Z-3 is in lock-out mode and will not accept remote commands, activate
the door from the pushbutton wall console.
4. Once the GD00Z-3 has initiated the movement of the garage door, another
command cannot be sent for 30 seconds. This eliminates the chance of “bouncing”
the garage door and possibly damaging the garage door opener.
➓TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Unable to include in
Z-Wave network.
GD00Z-3 was not
properly excluded
from a previous
Z-Wave network.
1. Reset the GD00Z-3 by pressing
the LINK button 5 times. A quick
beep followed by a longer beep
will indicate the reset.
The GD00Z-3 does
not flash or beep
when activated.
No power to the
GD00Z-3.
1. Make sure the power supply is
plugged in securely to a live outlet.
2. Make sure the power cord
is plugged in securely to the
GD00Z-3.
The GD00Z-3
flashes and beeps
when activated but
the door does not
move.
Obstruction
blocking the door
or incorrect wiring.
1. Make sure that there are no obstacles
preventing the door from moving.
2. Make sure that the GD00Z-3
connection wires are connected
to the proper terminals on the
garage door opener. Trace the
wires from the garage door
opener’s pushbutton wall console
to the door opener. This is where
the GD00Z-3 connection wires
should be connected to.
Garage door opens
or closes, but the
status does not
change on the Web
site or mobile app.
The tilt sensor
signal is not being
received by the
GD00Z-3.
1. Make sure the tilt sensor is
mounted correctly on the garage
door, with the arrowpointing up.
2. Make sure the battery pull tabhas
been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
LIMITED RETAIL WARRANTY
Linear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be free of
defects in materials and workmanship for a period of one (1) year from the date of purchase.
The Company within said period shall at its option, either repair or replace free of charge, any product or part
thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or replaced product
to the purchaser at Company’s expense.
The GD00Z-3 is sold exclusively through Nexia Home Intelligence. For warranty service, contact Nexia Customer
Service at 877-288-7707.
This warranty is conditioned on the following:
1. The Company must be notified within one year of purchase and have been given the opportunity of
inspection by return of any alleged defective product free and clear of all liens and encumbrances to
the Company or its distributor; and
2. The product must not have been abused, misused or improperly maintained and/or repaired during
such period; and
3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear.
THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE
HEREBY DISCLAIMED.
The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event shall the
Company be liable for any consequential, indirect, incidental, or special damages of any nature arising from the
sale or use of the product, whether based in contract, tort, strict liability or otherwise.
Note: Some states do not allowlimitations on incidental or consequential damages or howlong an implied
warranty lasts, so that the above limitations may not fully apply. This warranty gives specific legal rights and you
may also have other rights which may vary from state to state.
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
Les changements oumodifications non approuvés expressément par la partie responsable de la conformité
pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-3 - LINEAR P/N: 236386 X10 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
The GD00Z-3 typically
mounts on the ceiling
near the opener and
the power outlet
Tilt sensor
mounted on
the top panel
of the door
THE GD00Z-3 CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE GD00Z-3 WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
3/16" HOLES
FOR ANCHORS
The optional adjustable
mounting bracket fits
3 ways on the GD00Z-3
The bracket snaps onto
indents on either side or
on the end of the GD00Z-3
Secure
bracket
with screw
Use the four screws
and anchors to mount
the GD00Z-3 above
the opener
INDENT
INDENT
Use the bolts and nuts supplied
to attach the bracket to a secure
structure
BE SURE THE GD00Z-3
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
INDENT
1A
2A
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
! WARNING !
1
PUSHBUTTON
PUSHBUTTON
GARAGE
DOOR
OPENER
Connect the GD00Z-3 connection
wires to the pushbutton wall console
terminals on the garage door opener.
The terminals may be named "PWC", "WC",
"PB", "PUSHBUTTON", or "RED and WHITE".
Terminal names and locations vary by model.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
Remove the screw from 120 VAC
outlet faceplate. Secure the retaining
bracket to the faceplate with the provided
screw. Snap the power supply into the
bracket while plugging into the outlet.
USE WIRE TIES TO SECURE
EXCESS WIRING CLEAR
OF ALL MOVING PARTS
OF THE GARAGE
DOOR AND OPENER
Either wire can
connect to either
terminal
Plug the power cord
into the power input
jack on the GD00Z-3
2
1
3
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
Use the Nexia portal or
mobile app to control
your garage door
The GD00Z-3 will activate
the door opener and open
or close the door
STAY CLEAR
OF THE DOOR !!!
3
The GD00Z-3 will beep and
flash for five seconds before
the door moves
4
5
6
The Web page or mobile
app will show the new status
of the door after the door
completes its cycle
Restore power to your
garage door opener
1
To synchronize the system,
use the garage door opener's
pushbutton to manually open
and close the door
2
STAY CLEAR
OF THE DOOR !!!
Use Nexia to add your garage door control
to Automations and Modes. For example:
Schedule your garage door to close at
sunset. See HELP at mynexia.com
for more details.
Copyright © 2014 Linear LLC 236386 X10
GD00Z-3 Specifications
Power Supply: Input: 120 VAC, 0.8 A
Output: 12 VDC, 2 A
OperatingTemperature: -4º—122° F (-20º—50° C)
Audible Alarm: 45 db@ 10 feet
Strobe: 360 Lumens
Communications: Z-Wave (908.4 MHz)
Mounting: Screws and anchors to
the ceiling, or bracket to the
opener’s hanging hardware
Tilt Sensor Specifications
Power Supply: Type CR2032 Coin Cell Battery
OperatingTemperature: -4º—122° F (-20º—50° C)
Battery Life: 24 Months (typical)
Communications: Proprietary 345 MHz
Range: 100” line-of-sight to GD00Z-3
Mountingto Garage Door: Double-sided tape or two
mounting screws
(Specifications subject to change without notice)
NOTICETO USERS IN CALIFORNIA - CR COIN
CELL LITHIUM BATTERY INFORMATION: THIS
PRODUCT CONTAINS A CR COIN CELL LITHIUM
BATTERY WHICH CONTAINS PERCHLORATE
MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.