Linksys NSS4000 Series User manual

QUICK INSTALLATION GUIDE
Linksys Business Series Network Attached Storage
Models NSS4000 and NSS6000

Linksys Business Series NSS4000 and NSS6000

Linksys Business Series NSS4000 and NSS6000
1
Linksys NSS4000/NSS6000
181356

Linksys Business Series NSS4000 and NSS6000
2Install Disk Drives

Linksys Business Series NSS4000 and NSS6000
3
Remove Drive Trays

Linksys Business Series NSS4000 and NSS6000
4Install Drive in Drive Trays

Linksys Business Series NSS4000 and NSS6000
5
Insert Drive Trays
181352

Linksys Business Series NSS4000 and NSS6000
6Install: Rack

Linksys Business Series NSS4000 and NSS6000
7
Install: Desktop (optional)
AUX 1

Linksys Business Series NSS4000 and NSS6000
8Rear Panel
181363
AUX 1

Linksys Business Series NSS4000 and NSS6000
9
181364
RPS
(optional, not included)
Linksys One Services Router
LAN
APC Smart UPS
(optional, not included)
Ethernet cable
(included)
Connect Devices

Linksys Business Series NSS4000 and NSS6000
10 Connect to Power

Linksys Business Series NSS4000 and NSS6000
Regulatory Compliance and Safety Information
The Linksys Business Series models NSS4000 and NSS6000 meet the following regulatory compliance and safety
standards:
Specification Description
Regulatory Compliance Products with the CE Marking indicate compliance with the 89/336/EEC and 73/23/EEC
directives, which include the safety and EMC standards listed below.
Safety
UL 60950-1
IEC60950-1 CB /PSB
CSA C22.2 No.60950-1-03
EN 60950-1
EMC
FCC Part 15 (CFR 47) Class A
ICES-003 Class A
EN 55022 Class A
CISPR22 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3

Linksys Business Series NSS4000 and NSS6000
FCC Part 15 Class A Compliance
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was
probably caused by the Linksys equipment or one of its peripheral devices. If the equipment causes interference to
radio or television reception, try to correct the interference by using one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Move the equipment to one side or the other of the television or radio.

Linksys Business Series NSS4000 and NSS6000
• Modifications to this product not authorized by Linksys could void the FCC approval and negate your
authority to operate this product.
Warning You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Industry Canada Statement
This device complies with Canadian ICES-003 rule.
Cet appareil est conforme a la norme NMB-003 d'Industry Canada.
EC Declaration of Conformity (Europe)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive
93/68/EEC, this product meets the requirements of the following standards:
• EN55022 Emission
• EN55024 Immunity

Linksys Business Series NSS4000 and NSS6000
Safety Information
The following statements are warnings or safety guidelines. A warning means danger. You are in a situation that
could cause bodily injury. Before working on equipment, be aware of the hazards involved with electrical circuitry
and standard safety practices to prevent accidents.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on
any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate its
translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Warning
Work During Lightning Activity
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning
Installation Instructions
Read the installation instructions before connecting the system to the power source.

Linksys Business Series NSS4000 and NSS6000
Warning
SELV Circuit
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage
(TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN
ports both use RJ-45 connectors. Use caution when connecting cables.
Warning
Equipment Installation
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Comply with Local National Electrical Codes
Installation of the equipment must comply with local and national electrical codes.
Warning
Product Disposal
Ultimate disposal of this product should be handled according to all national laws and regulations.

Linksys Business Series NSS4000 and NSS6000
Environmental Specifications
Dimensions 17.31” x 16.62” x 1.75” (439 mm x 422 mm x 44.45 mm)
Unit Weight 21 lbs (9.52 kg) (with drives installed)
Power 150 Watt, 12V, AC Power Adapter
Certification CE Class A, FCC Class A, UL, CUL
Security On disk data encrpytion with encrpytion key
Operating Temp 32º to 113ºF (0 to 40º C)
Storage Temp -4º to 158ºF (-20 to 70º C)
Operating Humidity 10 to 90 % RH
Storage Humidity 10 to 95% RH

Linksys Business Series NSS4000 and NSS6000
Power Supply Safety Warnings
When using the Linksys Business Series models NSS4000 and NSS6000, observe the following power supply
safety warnings:
Warning
TN Power
The device is designed to work with TN power systems.
Warning
Ground Conductor Warning
Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground
conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that
suitable grounding is available.
Warning
Power Supply Installation Warning
The power supply must be placed indoors.

Linksys Business Series NSS4000 and NSS6000
Caution Only use the Linksys-specified power supply. Refer to the installation manual provided with this
product.
Warning
Circuit Breaker
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than: 120 VAC, 15A U.S. (240 VAC, 10A international)
Warning
Main Disconnecting Device
The plug-socket combination must be accessible at all times, because it serves as the main disconnecting
device.