Linksys WPS54G - Wireless-G PrintServer Print Server User manual

A Division of Cisco Systems, Inc.
®
Model No.
PrintServer
Wireless-G
WPS54G
User Guide
WIRELESS
GHz
2.4
802.11g

Wireless-G PrintServer
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
How to Use this User Guide
The user guide to the Wireless-G PrintServer has been designed to make understanding networking with the
PrintServer easier than ever. Look for the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section.
This exclamation point means there is a caution or
warning and is something that could damage your
property or the PrintServer.
word: definition.
This checkmark means there is a note of interest and
is something you should pay special attention to while
using the PrintServer.
This question mark provides you with a reminder about
something you might need to do while using the PrintServer.
Figure 0-1: Sample Figure Description
WPS54G-UG-40915NC JL
WARNING: This product contains chemicals, including lead, known
to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.

Wireless-G PrintServer
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this Guide? 2
Chapter 2: Getting to Know the PrintServer 4
The Bottom Panel 4
The Front Panel 5
Chapter 3: Connecting the PrintServer 6
Overview 6
Connecting the PrintServer to Your Network 6
Placement Options 7
Chapter 4: Configuring the PrintServer Using the Setup Wizard 8
Installation 8
Chapter 5: Windows Driver Installation 13
Overview 13
Installation 13
Starting the Print Driver Utility 16
Chapter 6: Configuring the PrintServer Using the Web-based Utility 18
Overview 18
The Setup Tab 19
The Protocol Tab - TCP/IP 20
The Protocol Tab - AppleTalk 21
The Protocol Tab - NetBEUI 22
The Protocol Tab - SNMP 23
The Wireless Tab - Basic 24
The Wireless Tab - Security 25
The Printer Tab - Internet Printing 26
The Printer Tab - Logical Port 27
The Status Tab - Device 28
The Status Tab - Printer 29
The Status Tab - Wireless 29
The Exit Tab 29

Wireless-G PrintServer
Chapter 7: Bi-Admin Management 30
Overview 30
Bi-Admin Installation 30
Starting the Bi-Admin Management Utility 32
The Bi-Admin Management Utility 33
Chapter 8: Internet Printing Protocol (IPP) 44
Overview 44
Windows IPP Client Setup 44
Appendix A: Troubleshooting 49
Common Problems and Solutions 49
Appendix B: Wireless Security 51
Security Precautions 51
Security Threats Facing Wireless Networks 51
Appendix C: About Bi-Directional Printing 54
Appendix D: Upgrading Firmware 55
Appendix E: Windows Help 56
Appendix F: Glossary 57
Appendix G: Specifications 64
Appendix H: Warranty Information 65
Appendix I: Regulatory Information 66
Appendix J: Contact Information 68

Wireless-G PrintServer
List of Figures
Figure 2-1: PrintServer’s Bottom Panel 4
Figure 2-2: PrintServer’s Front Panel 5
Figure 3-1: Connect to the Ethernet Port 6
Figure 3-2: Connect to the USB Port 6
Figure 3-3: Connect to the Power Port 6
Figure 3-4: Desktop Placement 7
Figure 4-1: Welcome 8
Figure 4-2: Wireless-G PrintServer Setup 8
Figure 4-3: Basic Settings 9
Figure 4-4: IP Settings 9
Figure 4-5: Set PrintServer’s Password 10
Figure 4-6: Wireless Settings 10
Figure 4-7: Wireless Security Settings 11
Figure 4-8: Wireless Security Settings - WEP Key 11
Figure 4-9: Confirmation 12
Figure 4-10: Congratulations 12
Figure 5-1: Welcome 13
Figure 5-2: Driver Setup Welcome 14
Figure 5-3: Choose Destination Location 14
Figure 5-4: Select Program Folder 15
Figure 5-5: Setup Complete 15
Figure 5-6: Information 16
Figure 5-7: Printer Port Setup 16
Figure 5-8: Configure Printer Port 17
Figure 6-1: Setup Tab 19
Figure 6-2: Protocol Tab - TCP/IP 20
Figure 6-3: Protocol Tab - AppleTalk 21
Figure 6-4: Protocol Tab - NetBEUI 22
Figure 6-5: Protocol Tab - SNMP 23
Figure 6-6: Wireless Tab - Basic 24
Figure 6-7: Wireless Tab - Security (Pre-Shared Key) 25

Wireless-G PrintServer
Figure 6-8: Wireless Tab - Security (WEP) 25
Figure 6-9: Printer - Internet Printing 26
Figure 6-10: Printer - Logical Port 27
Figure 6-11: Status Tab - Device 28
Figure 6-12: Firmware Upgrade 28
Figure 6-13: Status Tab - Printer 29
Figure 6-14: Status Tab - Wireless 29
Figure 6-15: Exit 29
Figure 7-1: Welcome 30
Figure 7-2: Bi-Admin Setup Welcome 30
Figure 7-3: Choose Destination Location 31
Figure 7-4: Select Program Folder 31
Figure 7-5: Connected Protocol 32
Figure 7-6: Searching for Device 32
Figure 7-7: Bi-Admin Management Utility 33
Figure 7-8: Device Information 33
Figure 7-9: Printer Status 34
Figure 7-10: Configuration - System 35
Figure 7-11: Configuration - TCP/IP 36
Figure 7-12: Configuration - AppleTalk 37
Figure 7-13: Configuration - NetBEUI 38
Figure 7-14: Configuration - Internet Printing 39
Figure 7-15: Configuration - Port 40
Figure 7-16: Configuration - Wireless 41
Figure 7-17: Configuration - SNMP 42
Figure 7-18: Upgrade 43
Figure 7-19: Detected LAN Cards 43
Figure 7-20: BIN File Information 43
Figure 7-21: Add Cross Segment PrintServer 43
Figure 8-1: Windows XP - Local or Network Printer 46
Figure 8-2: Windows XP - Specify a Printer 47
Figure 8-3: Windows 2000 - Locate Your Printer 47
Figure D-1: Status Tab - Device 55
Figure D-2: Firmware Upgrade 55

1
Chapter 1: Introduction
Welcome
Wireless-G PrintServer
Chapter 1: Introduction
Welcome
Thank you for choosing the Linksys Wireless-G PrintServer. The PrintServer lets you connect a USB printer
directly to your network, eliminating the need to dedicate a PC to print sharing chores. Using a PrintServer frees
up your “print share PC” so you don’t have to leave it on all the time. It also removes the printing bottleneck, and
sets your PC free to do more useful work.
The USB port is compatible with USB 1.1 printers, as well as printers that support the new high-speed USB 2.0
specification for even faster throughput.
How does the PrintServer do all of this? A print server is a device that allows multiple computers to share a
printer over a network. You can connectthe PrintServer directly to your network using an Ethernet network cable,
or you can connect the PrintServer over Wireless-G (802.11g) at up to 54Mbps. The wireless option lets you put
your printer wherever you want to, without having to run a cable. Whichever way the PrintServer is attached to
your network, both your wireless and wired PCs will have access to it and its USB printer.
But what does all of this mean?
Networks are useful tools for sharing Internet access and computer resources. Multiple computers can share
Internet access, so you don’t need more than one high-speed Internet connection. Using the PrintServer, you can
access one printer from different computers. Plus, you can access data located on another computer’s hard drive
and play multi-player video games. So, networks not only are useful in homes and offices, but also can be fun.
PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is
why the network is called “wired”.
PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the
same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called
a WLAN, or Wireless Local Area Network. Your network router bridges wireless networks of both 802.11b and
802.11g standards and wired networks, allowing them to communicate with each other.
To guide you through the process of installing the PrintServer, run the Setup Wizard on the Setup CD-ROM (you
can use the instructions in the Quick Installation or User Guide to help you). After you have installed the
PrintServer, you can change its settings using its browser-based utility, which is described in this User Guide.
These instructions should be all you need to get the most out of the Wireless-G PrintServer.
ethernet: an IEEE standard network protocol that
specifies how data is placed on and retrieved from
a common transmission medium
lan (local area network): the computers and
networkingproductsthat makeupthe network
in your home or office
802.11b: an IEEE wireless networking standard
that specifies a maximum data transfer rate of
11Mbps and an operating frequency of 2.4GHz
802.11g: an IEEE wireless networking standard
that specifies a maximum data transfer rate of
54Mbps, an operating frequency of 2.4GHz, and
backward compatibility with 802.11b devices
browser: an application program that
provides a way to look at and interact with all
the information on the World Wide Web
mbps:onemillion bitsper second;a unitof
measurement for data transmission

2
Chapter 1: Introduction
What’s in this Guide?
Wireless-G PrintServer
What’s in this Guide?
This user guide covers the steps for setting up and using the PrintServer.
• Chapter 1: Introduction
This chapter describes the PrintServer’s applications and this User Guide.
• Chapter 2: Getting to Know the PrintServer
This chapter describes the physical features of the PrintServer.
• Chapter 3: Connecting the PrintServer
This chapter instructs you on how to connect the PrintServer to your network.
• Chapter 4: Configuring the PrintServer using the Setup Wizard
This chapter instructs you on how to use the Setup Wizard to install your PrintServer.
• Chapter 5: Windows Driver Installation
This chapter explains how to install the Windows driver for the PrintServer.
• Chapter 6: Configuring the PrintServer Using the Web-based Utility
This chapter explains use the web-based utility to change the PrintServer’s settings.
• Chapter 7: Bi-Admin Management
This chapter explains how to use the Bi-Admin Management utility, which is for advanced users only.
• Chapter 8: Internet Printing Protocol (IPP)
This chapter instruct you on how to use the PrintServer as an IPP server so you can run remote print jobs.
• Appendix A: Troubleshooting
This appendix describes some potential problems and solutions regarding use of the PrintServer.
• Appendix B: Wireless Security
This appendix explains the security risks in wireless networking and how you can help protect your network
• Appendix C: About Bi-Directional Printing
This appendix describes bi-directional printing.
• Appendix D: Upgrading Firmware
This appendix instructs you on how to upgrade the firmware on the PrintServer should you need to do so.

3
Chapter 1: Introduction
What’s in this Guide?
Wireless-G PrintServer
• Appendix E: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.
• Appendix F: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix G: Specifications
This appendix provides the technical specifications for the PrintServer.
• Appendix H: Warranty Information
This appendix supplies the warranty information for the PrintServer.
• Appendix I: Regulatory Information
This appendix supplies the regulatory information regarding the PrintServer.
• Appendix J: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.

4
Chapter 2: Getting to Know the PrintServer
The Bottom Panel
Wireless-G PrintServer
Chapter 2: Getting to Know the PrintServer
The Bottom Panel
The PrintServer’s ports and Reset button are located on the bottom panel.
Power The Power port is where you will connect the power adapter.
Ethernet The Ethernet port is where you will connect the PrintServer to your wired network. (This is
optional.)
USB Printer The USB Printer port is where you will connect the USB printer to the PrintServer.
The USB icon (right) designates a USB port. The PrintServer comes with a USB
cable. One end has a rectangular connector called Type A. The other end has a
square connector called Type B. The USB cable’s Type A end connects to the
PrintServer, and the Type B end connects to the printer.
Reset Button Use the Reset Button to reset the PrintServer to its factory defaults or print a test page. The
instructions are provided on the right side of this page.
IMPORTANT: Resetting the PrintServer will
delete all of your settings and replace them
with the factory defaults. Do not reset the
PrintServer if you want to retain the settings.
Figure 2-1: PrintServer’s Bottom Panel
To reset the factory default settings
1. Unplug the PrintServer.
2. Press and hold the Reset button. While pressing the
button, plug in the PrintServer.
3. If you continue pressing the button for 10 seconds,
the PrintServer will be reset to factory defaults.
To generate a diagnostic print-out
1. Ensure that both the PrintServer and the printer
attached to the Printer port are ON.
2. Press the Reset button, and hold it in for 2 seconds.
3. The test page, which lists the current settings, will
be printed.
PostScript printers are unable to print this page. If you
have a PostScript printer on the USB Printer port, the
test page will not be printed.
USB Connector-Type A USB Connector-Type B

5
Chapter 2: Getting to Know the PrintServer
The Front Panel
Wireless-G PrintServer
The Front Panel
The PrintServer’s LEDs are located on the front panel.
Power Green/Orange. If the Power LED is continuously lit green, then the PrintServer is ready for use.
The LED flashes green when the PrintServer is booting up, a system self-test is running, or the
firmware is being upgraded. It lights up orange when there is an error.
Ethernet Green/Orange. If the Ethernet LED is continuously lit green, the PrintServer is successfully
connected to a device through the Ethernet port. The LED flashes green when the PrintServer
is actively sending or receiving data from the wired network.It flashes orange when there are
collisions detected on the Ethernet port.
Wireless Green. The Wireless LED serves two purposes. If the LED is continuously lit, the PrintServer is
successfully connected to the wireless network. If the LED is flashing, the PrintServer is
actively sending or receiving data from the wireless network.
USB Green/Orange. The USB LED lights up green when there is a printer connected to the USB port.
The LED flashes green when the PrintServer is sending data through the USB port. It lights up
orange when there is a problem with the USB printer.
Figure 2-2: PrintServer’s Front Panel

6
Chapter 3: Connecting the PrintServer
Overview
Wireless-G PrintServer
Chapter 3: Connecting the PrintServer
Overview
Before starting the physical installation, note the PrintServer’s default name, which starts with “LK” (for example,
LK71107). The default name is shown in the Server field on the PrintServer’s sticker, which is located on the
PrintServer’s back panel. During the PrintServer driver installation, this name is used to identify the PrintServer
you are currently installing.
Connecting the PrintServer to Your Network
1. Use the USB cable to connect your USB printer to the PrintServer’s USB Printer port. Plug the Type A
connector end into the PrintServer and the Type B connector end into the printer.
2. If you are connecting the PrintServer to your wired network, then plug one end of the Ethernet network cable
into the PrintServer’s Ethernet port.
Then connect the other end of the cable to your router or switch. The distance between the PrintServer and
the other device should not exceed 328 feet (100 meters).
3. Power on your printer.
4. Plug the power adapter into the PrintServer’s Power port.
Then plug the other end into an electrical outlet.
Proceed to the next section, “Placement Options.”
Figure 3-1: Connect to the Ethernet Port
NOTE: The PrintServer does not have an on/off power switch. Whenever its power adapter is
plugged into a power supply, the PrintServer is powered on. The PrintServer can be powered on
before, during, or after your network is powered on.
Figure 3-2: Connect to the USB Port
Figure 3-3: Connect to the Power Port
IMPORTANT: Makesure youuse the poweradapter suppliedwith thePrintServer.Useof a different
power adapter could damage the PrintServer.

7
Chapter 3: Connecting the PrintServer
Placement Options
Wireless-G PrintServer
Placement Options
There are different ways to place the PrintServer. The first way is to place the PrintServer horizontally on a
surface, so it sits on four small rubber pads. You can also use the included velcro to mount the PrintServer on a
wall or underneath a shelf. To use the velcro, follow these instructions:
1. Separate the included velcro into its two sides, the hook side and the loop side. You will use the tape on the
backs of the velcro sides to attach them to the PrintServer and surface you want to use.
2. For the first velcro side, peel off the cover protecting the tape, and attach it to the recessed area on the back
panel of the PrintServer.
3. For the other velcro side, peel off the cover, and attach it to the location you have chosen for the PrintServer.
4. Attach the velcro sides to each other, and make sure the PrintServer is securely mounted on the wall or
underneath the shelf.
5. Adjust the position of the antenna so that it is positioned as high as possible. Usually, the higher you place the
antenna, the better the performance and range will be.
The physical installation of the Wireless-G PrintServer is complete. Proceed to “Chapter 4: Configuring
the PrintServer Using the Setup Wizard.” Figure 3-4: Desktop Placement

8
Chapter 4: Configuring the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer
Chapter 4: Configuring the PrintServer Using the Setup Wizard
Installation
To install the PrintServer, you will use the Setup CD-ROM to run the Setup Wizard. It is highly recommended that
you use a computer on the wired network to set up the PrintServer. However, if you only have a wireless network,
then you can use a computer on the wireless network to set up the PrintServer.
1. Insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup Wizard should run automatically. If it
does not, click the Start button and choose Run. In the box that appears, enter D:\setupWizard.exe (if “D”
is the letter of your CD-ROM drive).
2. When you see the Welcome screen, click Setup Wizard to continue. Click Exit to end the installation. Click
User Guide button to view the User Guide.
3. After the Setup Wizard has found the PrintServer, the Wireless-G PrintServer Setup screen will appear. If this
is the first time you have run the Setup Wizard, make sure that List only new (unconfigured) Print Servers
is selected and your PrintServer is listed by its default server name. Next to the PrintServer’s Server Name is
its IP Address. Note the IP Address so you can use it to access the PrintServer’sweb-based utility, as
described in “Chapter 6: Configuring the PrintServer Using the Web-based Utility.”
If you have previously configured the Print Server, select List all compatible Print Servers. Click Next to
continue.
Click the Refresh button to refresh the screen. Click Back to return to the previous screen.
Figure 4-1: Welcome
Figure 4-2: Wireless-G PrintServer Setup
ip address: the address used to identify a
computer or device on a network.

9
Chapter 4: Configuring the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer
4. The Basic Settings screen will appear. If you want to change the Device Name or Domain Name, enter the
Device Name and Domain Name in the respective fields.
Click Next to continue, or click Back to return to the previous screen.
5. The IP Settings screen will appear. If your network uses a router with a DHCP setting that automatically
assigns IP addresses, select Automatically obtain an IP address (DHCP). If your network uses a static IP
address, select Set IP configuration manually, and enter the IP Address, Subnet Mask, and Gateway in the
fields provided.
Click Next to continue, or click Back to return to the previous screen.
Figure 4-3: Basic Settings
Figure 4-4: IP Settings
static ip address: a fixed address assigned to
a computer or device connected to a network.
ip (internet protocol): a protocol
used to send data over a network
ip address: the address used to identify
a computer or device on a network

10
Chapter 4: Configuring the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer
6. The Set PrintServer’s Password screen will appear. If you want to change your password, enter your current
password in the Current Password field. Enter the new password in the New Password field, then enter it
again in the Verify Password field.
Click Next to continue, or click Back to return to the previous screen.
7. The Wireless Settings screen will appear. In the SSID field, enter your wireless network’s SSID or name. This
is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have
32 characters or fewer.
Select the channel at which the network broadcasts its wireless signal (available only if you selected Ad-Hoc
for the Network Type setting).
The Network Type setting shows a choice of two wireless modes. Select Infrastructure if you want the
PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you want the
PrintServer to communicate without using an access point or wireless router.
Click Next to continue, or click Back to return to the previous screen.
Figure 4-5: Set PrintServer’s Password
Figure 4-6: Wireless Settings
ad-hoc: agroupof wirelessdevices communicating
directly to each other (peer-to-peer) without the use
of an access point.
infrastructure:configurationin whichawirelessnetwork
is bridged to a wired network via an access point.
ssid: your wireless network’s name.

11
Chapter 4: Configuring the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer
8. The Wireless Security Settings screen will appear. If you want to enable WEP encryption for greater wireless
security, select the level of WEP encryption, 64 Bit Keys or 128 Bit Keys, and then enter a Passphrase. If you
use a Passphrase,a WEP key will be automatically generated after you click the Next button. The Passphrase
iscase-sensitiveand should have16 alphanumeric charactersor fewer. It must match the passphrase of your
wireless network and is compatible with Linksys wireless products only. (You will have to enter the WEP
key(s) manually on any non-Linksys wireless products.)
If you want to enter the WEP key manually, then leave the Passphrase field blank; you will be able to enter a
WEP key on the following screen. If you want to disable WEP encryption, keep the default, Disabled.
Click Next to continue, or click Back to return to the previous screen.
9. If you entered a Passphrase, you will see the automatically generated WEP key on the following screen.
Otherwise, enter the WEP keymanually in the field provided. If you are using 64-bit WEP encryption, then the
key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key
must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are “0”-“9” and “A”-“F”.
Click Next to continue, or click Back to return to the previous screen.
Figure 4-7: Wireless Security Settings
passphrase: used much like a password, a passphrase
simplifies the WEP encryption process by automatically
generating the WEP encryption for Linksys products.
wep (wired equivalent privacy): a method of
encrypting data transmitted on a wireless network for
greater security.
Figure 4-8: Wireless Security Settings - WEP Key
NOTE: The Wireless-G PrintServer also offers a Pre-Shared Key option for wireless security. To use
this method, refer to the Wireless Tab - Security section of “Chapter 6: Configuring the PrintServer
Using the Web-based Utility” for instructions.

12
Chapter 4: Configuring the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer
10. The Confirmation screen will appear. Your old and new settings will be displayed. If you want to save the new
settings,click Yes. If you want to make a change, click No, andyou will exit the Setup Wizard; you will have to
start the Setup Wizard again.
11. The Congratulations screen will appear. The setup is complete.
You will need to install the driver next. Click User Install at the bottom of the Congratulations screen, and go
to “Chapter 5: Windows Driver Installation.”
Figure 4-9: Confirmation
Figure 4-10: Congratulations

13
Chapter 5: Windows Driver Installation
Overview
Wireless-G PrintServer
Chapter 5: Windows Driver Installation
Overview
This section installs the PrintServer’s software on your Windows 98, Me, 2000, or XP computers so they can use
the PrintServer for print jobs. (The PrintServer is fully compatible with Windows 98, Me, 2000, and XP.)
At this point, you must have the following:
• the PrintServer hardware installed on your network. If not, see “Chapter 3: Connecting the PrintServer.”
• TCP/IP installed on each of your computers.
• an IP address assigned to each of the computers on your network.
• an IP address assigned to the PrintServer by you or your network router. By default the PrintServer has DHCP
enabled so the network router will automatically assign an IP address. If you need to manually assign an IP
address, run the Setup Wizard on the Setup CD-ROM or go to “Chapter 7: Bi-Admin Management.”
It is assumed that your CD-ROM drive’s letter name is designated as “D”. If your CD-ROM driveis named another
letter, replace all instances of “D” with the appropriate letter.
If you need to install the PrintServer’s driver on computers without a CD-ROM drive, you can create asetup disk
by using a computer with a CD-ROM drive to copy the contents of D:\Driver\PTP onto a floppy disk.
Installation
1. Make sure you have no programs or applications running on your computer.
2. If you haven’t already done so, insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup CD-
ROM should run automatically. If it does not, click the Start button and choose Run. In the field that appears,
enter D:\setupWizard.exe (if “D” is the letter of your CD-ROM drive).
3. When you see the Welcome screen, click User Install to continue. Click Exit to end the installation.
Figure 5-1: Welcome
HAVE YOU:already set up your printer? Linksys
recommends that you set up your printer and
install your printer’s driver before you install the
PrintServer’s driver.

14
Chapter 5: Windows Driver Installation
Installation
Wireless-G PrintServer
4. The Welcome screen of the driver installation program will appear first. ClickNext to continue with the driver
installation, or click Cancel to quit the setup program and then close the open programs.
5. The Choose Destination Location screen will appear. Choose the location where the driver’s folder will be
installed. To install the driver in the default location, click Next to continue.
If you want the folder to be installed in a different location, click the Browse button and select the location.
Then click Next to continue.
You can also click Back to return to the previous screen or click Cancel to end the driver installation.
Figure 5-3: Choose Destination Location
Figure 5-2: Driver Setup Welcome