LinOra WIFIRANGER TETON C-19 User manual

!
School Bus Quick Start Guide
1) Find a rooftop mounting location on the school bus that is at
least 24” from any other appliance or obstruction."This
location should be as close to the centerline of the bus as
possible and as level as possible. The Teton C19 outdoor
router will function better with more clearance in all
directions.
2) Mark the location where you will be mounting the router.
Also determine how to route the power cable of the Teton
C19 router to the inside of the school bus where the indoor
Go2 / Core router is located. Ensure that the WiFiRanger
embossed logo is facing towards the front of the RV (Fin-
always-faces-forward)."
3) If drilling an entry-hole for the power cable, trace and drill a
hole in the vehicle roof where the cable exits from the rear of
the enclosure."Alternately, you can route the power cable
inside the bus through a window or entry vent if you don’t
want to drill a hole in the rooftop.""
4) Route the cable through the newly drilled hole or alternate
entry method and to the location where the indoor Go2 /
Core router is located.
5) Thoroughly clean off the roof area where you will be
mounting the router, ensuring full adhesion.
6) Once the cable is appropriately routed to the inside of the
RV, seal the hole around the cable with sealant if applicable.
7) Mount the router to the roof using either screws and sealant
or sealant only. If using screws and sealant, drill pilot holes
then snug screws with dabs of sealant. If using sealant only,
apply sealant on entire base of router for maximal adhesion
(only use high-grade sealant appropriate for school bus roof
material).
8) Continue with router setup process on page 2
TETON (C-19)
©2020 LinOra Corp
[e-mail] | 208.321.5544
QSG_BUSC19_TETONPMv2 | 1
▼PERMANENT INSTALLATION ▼
24”
minimum
clearance
24”
minimum
clearance
24”
minimum
clearance
24”
minimum
clearance

1Route ethernet cable down to inside of school bus and plug into port 5 of Go2 / Core router
2Power Teton (C-19) by turning ignition key of school bus to ON position (depending on model)
3Wait 3 minutes for Teton (C-19) to power up and connect to Ethernet WAN (Go2 / Core)
4Connect student devices wirelessly to public broadcast named SchoolBusInternetXXYY
5Have students go to mybusinternet.com if not automatically redirected to login page
6Authenticate students by entering accessXXYY as the passcode when prompted
Students may now use the internet with speeds limited to 3x3Mbps each to ensure fair bandwidth
ACCESSING CONTROL PANEL FOR ADMINISTRATION (if applicable):
Use one of the following devices: Smartphone | Tablet | Laptop
1Connect device to private broadcast named Pvt.WFR_Teton.XXYY
2Enter changemenowXXYY when prompted for WPA2 password
3Open device’s web browser (Chrome, Safari, Internet Explorer, Firefox, etc)
4Go to mywifiranger.com or 10.1XX.YY.1:8080 to bring up the Control Panel
5Get online using desired internet connection method on Main tab of Control Panel
6Change desired settings (if applicable) on pertinent tab then click Save Changes
School Bus Quick Start Guide
TETON (C-19)
©2020 LinOra Corp
[e-mail] | 208.321.5544
QSG_BUSC19_TETONPMv2 | 2
▼ROUTER SETUP ▼
Replace XX and YY with Unique Numbers of the Teton (C-19)
Note that the XX and YY are only placeholders within this generic guide, representing where the actual numbers reside. Each Teton
(C-19) has a unique identification number which is displayed in its WiFi broadcasts and is used in its passcode and password.
EXAMPLE: if the unique identification number of the router was 7823, then the public broadcast would be
SchoolBusInternet7823 with the passcode access7823 and the private broadcast would be Pvt.WFR_Teton.7823 with the
WPA2 password changemenow7823 (this example for illustration purposes follows the consistent schema of XXYY = 7823).
Plug-n-Play Configuration
The Teton (C-19) is
configured to automatically
work out of the box.
However, if small changes or
troubleshooting is required,
these steps will provide
administrative access.
SCAN QR CODE
TUTORIAL VIDEO