LINSY HOME LS200E4-A User manual

Assembly Instructions - Please keep for future reference
Dimensions
Width - 25.39inch
Depth-11.30inch
Height - 29.72inch
Dresser with 6 Drawers
LS200E4-A
If you need help or have damaged or missing parts, email:
[email protected]
Important – Please read these instructions before assembly
1

2
MAX
11KGS
please contact us via email: [email protected]
scratches, use a car polish.
following chemicals: acetone,
Do not clean it with cleaner with
dust to keep it clean.
you may use the dry cloth to clean the
you want to dump it.
local authority waste disposal centre if
with household waste. Take it to thein the unit from time to time.
Please check if there is any screws loosed
Only cleaning with a damp cloth and
responsibly.
Dispose of all packaging carefully and
hand screwdrivers we provided.
damage the unit. Only use
to insert screws, as it may
to use power drill or drivers
We do not recommend
before get start.
to put the parts out on the ground
may result in choken if swallow.
while you are installing, small parts
components and tools listed on the
Safety and Care Advice
– Please read these instructions fullybefore starting assembly
Please keep your receipt as proof of purchase. If you have any suggestions or problems,
Check that if you have all the
front cover and pages 3 - 4.
Remove all ttings from the plastic
bags and separate them into their
groups.
Keep children and animals away
Make sure you have enough space
Do not stand or put weight on the
product, which could cause damage.
Assemble the item as close to its
nal position (in the same room) as
possible.
Do not place furniture directly in
front of radiators, res or any other
source of heat.
Parts of the assembly
will be easier with 2
people.
Assemble on a soft level surface
to avoid damaging the unit or your
oor.
mild detergent, do no use bleach or
abrasive cleaners.
This product should not be discarded
Clean marks with a damp cloth.
Do not allow spillages to stay on the
surface for long.
To remove stubborn stains, wipe
over with a damp cloth and washing
up liquid.
Do not use abrasive cleaners.
(e.g nail varnish remover), Ammonia
(e.g.bleach), or Sodium hydroxide
(e.g. Caustic soda, drain and oven
cleaners).
In the event of accidental contact
with aggresive cleaners, rinse
thoroughly with water.
To remove stains and small
Place mats to protect the
surface from moisture and heat.
1 2
General care and maintenance
General information
Cleaning and care of high gloss surfaces
Important

Components
Please check you have all the pieces listed below
If you need help or have damaged or missing parts, email:
[email protected]
3
Part List
Reference Specications(mm) Quantity Material
745*287*32 1 Steel
745*287*32 1 Steel
607*284*45 1 Steel
613*13*13 Steel
φ5*732 1
2
Steel
Particle Board613*287*15 1
Fabric+Nonwovens+Fiber Board+Cardboard
Fabric+Nonwovens+Fiber Board+Cardboard
394*278*194
194*278*194
389*273*3
189*273*3
3
3
3
3
Description
Left Frame
Right Frame
Middle Frame
Connecting Tube
Support Frame
Top Panel
Small Drawer
Base for Large Drawer
Base for Small Drawer
Large Drawer
7
6
5
4
10
9
8
3
2
1
2.5MM Medium Density Fiberboard
2.5MM Medium Density Fiberboard

Components
Please check you have all the pieces listed below
If you need help or have damaged or missing parts, email:
[email protected]
M6x25 x 6 pcs
6 pcs
S4 x 1pc
4 pcs M6 x4 pcs
M6x12 x 2 pcs M7x48 x 4 pcs
M4x10 x 12 pcs
A
E F H
J
B C
G
2 pcs
I
1 pc
K
4
Assembly Instructions:Shelf on the left
Step 1
Assembly Instructions:Shelf on the left
Step 1
Assembly Instructions:Shelf on the left
Step 1
Assembly Instructions
Step 1
Jx 1 pc
Ax 4 pcsAx 4 pcsAx 4 pcsAx 4 pcs
M4x22x 4 pcs
D
L
Spare Parts
Spare Parts x 1 pc
1 of 1
Don’t screw tightly before all the screws
are put into the corresponding holes
Backside
Note: Side Frames face the same
direction, The holes face the backward
1
2
4
4

Assembly Instructions
Step 2
5
Backside
Jx 1 pc
x 4 pcsC
Jx 1 pc
x 2 pcsB
Backside
B
B
Step 3
Ax 4 pcsAx 4 pcsAx 4 pcsAx 2 pcs
3
6
Backside
B6
Don’t screw tightly before all the screws
are put into the corresponding holes
Don’t screw tightly before all the screws
are put into the corresponding holes

Assembly Instructions
Step 4
Step 5
6
x 4 pcsD
Ex 4 pcs
K x 1 pc
H x 4 pcs
Jx 1 pc
Fx 6 pcs
Gx 12 pcs
Jx 1 pc
Backside
K
H
H
H
H
G
G
5
5
7
9
8
10
Don’t screw tightly before all the screws
are put into the corresponding holes
x3 x3

Assembly Instructions
Step 6
Step 7
7
Jx 1 pc
I
7
7
7
8
8
8
I
Ix 2 pcs
All screws should be tightly
screwed