fantastic furniture COMO LOWLINE SMALL User manual

Assembly Instructions
LOWLINE SMALL 1200MM
COMO
VER 1.1

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws (leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
What You Need
To Assemble The Body
Top Panel
(P1) Right Side
Panel
(P3)
Left
Drawer Side
(P13)
Drawer Front
(P11ǃP12)
×2
Right Drawer
Side
(P14)
Drawer Back
(P16)
Drawer
Base(P15)
Support
Rail
(P17)
Left Side
Panel
(P2)
Rail
(P4)
Rail
(P5)
Shelf Panel
(P6)
Divider
(P7)
Divider
(P8)
Rail
(P9)
Back Panel
(P10)
(Tools not provided)
Flat BladeScrewdriver
Phillips Head Screwdriver
Mallet
25 x Dowels
(H1)
12 x Screws
(H2)
4 x Long
Screws
(H12)
34 x Small
Screws
(H5)
2 x CL Runner
Tracks
(H6)
2 x CR Runner
Tracks
(H7)
19 x Cam Bolts
(H3)
19 x Cam Nuts
(H4)
10 x Small
Cam Nuts
(H11)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
10 x Small
Cam Bolts
(H10)
Please make sure you have all these parts before you start.
6 x Plastic
Glides
(H13)

H5
H1
H1
H1
H3
H3
H5
H7
H5
Page 4
Step 1
You will need:
H5
H5
H5
H6
Step 2
You will need:
1 x CL Runner
Track
(H6)
1 x CR Runner
Track
(H7)
12 x
Dowels
(H1)
8 x
Cam Bolts
(H3)
Step 3
You will need:
1 x Dowel
(H1)
5 x
Cam Bolts
(H3)
6 x Small
Screws
(H5)
(P2)
(P4)
(P3)
(P2)
Attach 1 x CL Runner Track (H6) to Left Side Panel (P2) and 1 x CR Runner Track (H7)
to Right Side Panel (P3) with 6 x Small Screws (H5).
Insert 12 x Dowels (H1) into Side Panels (P2) and (P3),
Attach 8 x Cam Bolts (H3) into them as shown.
Insert 1 x Dowel (H1) into Rail (P5).
Attach 5 x Cam Bolts (H3) into Rails (P4,P5) and Shelf Panel (P6) as shown.
H1
H1
H1
H3
H3
H3
(P3)
H1
H1
H1
H1
H3
H3
H3
H3
(P6)
H3
H3
H3
(P5)
H1
H3
H6
CL
H5
H7
CR
H5

Page 5
Step 4
You will need:
2 x Cam Nuts
(H4)
(P4)
(P6)
Insert 2 x Cam Nuts (H4) into the holes of Shelf Panel (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Shelf Panel (P6) onto Rail (P4) and tighten the cam nuts.
Attach 1 x CL Runner Track (H6) to Divider (P8) with 3 x Small Screws (H5)
as shown, and then turn over to the other side.
Attach 1 x CR Runner Track (H7) with 3 x Small Screws (H5).
FLIP
H4
H4
H5
H5
H5
H6
H6
H5
H5
H5
H7
H7
(P8)
(P8)
Step 6
You will need:
1 x CL Runner
Track
(H6)
1 x CR Runner
Track
(H7)
6 x Small
Screws
(H5)
H5
CL CR
H5
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
H1
VENEERED
H1
Step 5
You will need:
(P4)
(P6)
(P7)
Insert 2 x Dowels (H1) into the holes of Divider (P7).
Attach Divider (P7) to Shelf Panel (P6) with 2 x Long Screws (H12).
H12
H12
2 x Dowels
(H1)
2 x Long Screws
(H12)

2 x Dowels
(H1)
(P6)
(P8) (P5)
(P9)
Insert 2 x Dowels (H1) into the holes of Divider (P8).
Insert 2 x Cam Nuts (H4) into the holes of Divider (P8).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Shelf Panel (P6) into place and tighten the cam nuts.
H4
H4
H1
Page 6
Step 8
You will need:
2 x Cam Nuts
(H4)
(P6)
(P3)
(P5)
(P9)
(P4)
Step 9
Insert 4 x Cam Nuts (H4) into the holes of Shelf Panel (P6) and Rails (P5,P9).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Right Side Panel (P3) into place and tighten the cam nuts.
You will need:
4 x Cam Nuts
(H4)
H4
H4
H4
H4
H4
(P5)
Insert 1 x Cam Nut (H4) into the hole of Divider (P8).
Rotate the cam nuts so the arrows point towards the incoming cam bolt.
Push Divider (P8) onto Rail (P5) place and tighten the cam nuts.
Attach Rail (P9) to Divider (P8) with 2 x Long Screws (H12).
(P8)
(P9)
H4
H12H12
Step 7
You will need:
1 x Cam Nut
(H4)
2 x Long
Screws
(H12)

(P3)
(P2)
(P8)
Page 7
Step 11
You will need:
Hammer 6 x Plastic Glides (H13)
on Side Panels (P2,P3) and Divider (P8).
H13
H13
H13
H13
H13
H13
6 x Plastic Glides
(H13)
H13
20mm
(P6)
(P3)
(P2)
(P5)
(P9)
Step 10
You will need:
Insert 4 x Cam Nuts (H4) into the holes of Shelf Panel (P6) and Rails (P5,P9).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Left Side Panel (P2) into place and tighten the cam nuts.
4 x Cam Nuts
(H4)
H4
H4
H4
H4

H5
H5
6 x Dowels
(H1)
(P1)
(P1)
(P2)
(P7)
(P3)
(P10)
Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown.
You will need:
6 x Cam Bolts
(H3)
H3
H3
H3
H3
H3
H3
H1
Page 8
Step 12
Step 13
You will need:
Turn carcase onto feet.
Insert 6 x Dowels (H1) into the holes of Side Panels (P2,P3) and Divider (P7).
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2,P3) and Divider (P7).
Rotate the cam nuts so the arrows point towardsthe incoming cam bolts.
Attach Top panel (P1) and tighten the cam nuts.
6 x Cam Nuts
(H4)
H1
H4
H4
H4
H1
H1
H4
H4
H4
H1 H1
Step 14
You will need:
14 x Small
Screws
(H5)
Turn carcase onto front.
Put Back Panel (P10) into the groove
on the back of the carcase, colour faces inside.
Attach with 14 x Small Screws (H5).

H10 H10
H11
H11
H11
H11
H11
1 x Dowel
(H1)
Page 9
Step 15
You will need:
5 x Small Cam
Bolts
(H10)
Step 16
Step 17
You will need:
(P11)
(P11)
(P11)
(P15)
(P13)
(P13)
(P14)
(P17)
(P14)
Insert 1 x Dowel (H1) into the hole of Drawer Front (P11).
Attach 5 x Small Cam Bolts (H10) as shown.
5 x Small Cam
Nuts
(H11)
Slide Drawer Base (P15) into the groove
in Drawer Sides (P13) and (P14) .
Insert 5 x Small Cam Nuts (H11) into the holes of Drawer Sides (P13,P14) and Support Rail (P17).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer
Sides (P13,P14) and Support Rail (P17) into place and tighten the cam nuts.
H10
H10
H10
H1
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

H2
H2
H2
Page 10
Step 18
You will need:
6 x Screws
(H2)
Step 19
You will need:
1 x DR Runner
(H9)
1 x DL Runner
(H8)
4 x Small
Screws
(H5)
Step 20
(P11)
(P15)
(P16)
(P13)
(P14)
H2
H2
H2
Attach 1 x DL Runner (H8) to the bottom of
Drawer Side (P13) and 1 x DR Runner (H9)
to the bottom of Drawer Side (P14) with
4 x Small Screws (H5).
Repeat step15 to step 19 to
assemble the other drawer.
Attach Drawer Back (P16) to Drawer Sides (P13,P14)
with 4 x Screws (H2),then attach Drawer Back (P16) to
Support Rail (P17) with 2 x Screws (H2).
Make sure that the groove lines up the whole way around the drawer.
(P14)
(P13)
H9
H8
H5
H5
H5
H5
H9
H8
DR
DL
H5
H5
H5
H5