Lippert Components Solera Installation instructions

1
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
Table Of Contents
Introduction ..............................................2
Safety Requirements.....................................2
Resources Required .....................................2
Variant Code Information ................................2
Installation of the Awning Rail ..........................3
Hanging the Window Awning............................3
Releasing Preset Tension................................4
Installation of Support Arms ...........................4
Installation of Pull Strap Bracket........................5
Operation .................................................7
To Open Window Awning................................7
To Close Window Awning................................7
Loading the Tension .....................................7
Maintenance ..............................................8
Fabric Care ..............................................8
Solera®
Window
Awning
Installation and
Owner’s Manual
(For Aftermarket Applications)

2
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
Introduction
The Solera®Window Awning is designed for use on most
recreational vehicle units and is available in a variety of
sizes to t even the largest unit.
Additional information about this product can be obtained
from www.lci1.com/support or by downloading the free
MyLCI app. The app is available on iTunes®for iPhone®
and iPad®and also on Google Play™for Android™users.
iTunes®, iPhone®and iPad®are registered trademarks of
Apple Inc. Google Play™and Android™are trademarks of
Google Inc.
Safety Requirements
variant
code
Resources Required
• Cordless or Electric Drill or Screw Gun
• Molly Rivets – ⁄" as needed
• Appropriate Drive Bits
• Measuring Tape
• Drill Bit – ⁄"
• Vise Grips
• Sealant
Variant Code Information
The variant code on Lippert products can assist LCI
customers in obtaining additional information about the
product and its components. On the Solera®Window
Awning, the label will be located on the fabric portion of the
assembly.
For replacement part information, locate the variant code
as outlined below, and call LCI customer service at
574- 537-8900.
NOTE: Prior to installation, please check the following
clearance. In order for the pull strap bracket to work
properly (See Installation of Pull Strap Bracket in this
document) clear wall space of 41" is needed for the
standard arm (18") or 65" is needed for the XL arm (33").
This measurement is taken from the channel of the awning
rail (located approximately 3" above the window frame) to
a position downward on the unit wall. This measurement
is especially critical on window awnings located on slide
room windows.
FAILURE TO FOLLOW THE INSTRUCTIONS PROVIDED
IN THIS MANUAL MAY RESULT IN DEATH, SERIOUS
INJURY, UNIT DAMAGE, OR VOIDING OF THE
COMPONENT WARRANTY.
ALWAYS WEAR EYE PROTECTION WHEN
PERFORMING SERVICE OR MAINTENANCE TO THE
UNIT. OTHER SAFETY EQUIPMENT TO CONSIDER
WOULD BE HEARING PROTECTION, GLOVES AND
POSSIBLY A FULL FACE SHIELD, DEPENDING ON THE
NATURE OF THE SERVICE.
MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP
CLEAR AND USE CAUTION.

3
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
Hanging the Window Awning
Fig.2
Fig.3
2. Position and center the awning rail approximately 3"
above the top of the window frame.
3. Apply a sealant behind the awning rail before securing
the awning rail with #8 - 18 x 1" self-drilling fasteners or
⁄" molly rivets (Fig.2).
Fig.4
2. Unroll one full roll of the fabric to slide the polycord
into the awning rail. If too much fabric is unrolled before
releasing the tension, there will not be enough tension to
sufciently retract the awning after use.
3. Insert the polycord into the channel in the awning rail
(Fig.4) and center the fabric with the awning rail.
polycord in
awning rail channel
Fig.1
Installation of the Awning Rail
1. Mark the center of the window and the center of the
awning rail (Fig.1).
1. Attach the support arm to the spring head assembly
and secure together with one #10 - 12 x 1" fastener (Fig.3).
Both arms are identical and can be used interchangeably.
Repeat for the other end.
DO NOT REMOVE THE COTTER PINS AT THIS TIME.

4
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
Fig.6
Fig.7
bottom of support arm
Releasing Preset Tension
cotter pin
Installation of Support Arms
1. Measure from the edge of the window frame to the arm
on both sides in two locations. Make sure the support arms
have the same amount of space on both sides and are
parallel to the side of the window frame. Mark the location
of the bottom of the support arm (Fig.7).
2. Apply sealant at the support arm fastening points. Install
fasteners, making sure the top of the roll tube end caps of
the support arm assemblies are just below the polycord
channel of the awning rail, and the arms are parallel with
the window frame.
Fig.5
4. Secure the fabric in the awning rail by installing a #6 x ½"
self-drilling fastener through the awning rail, polycord and
fabric 1" inside the edge of the fabric on both ends (Fig.5).
SPRINGS ARE UNDER TENSION WHEN COTTER PINS
ARE REMOVED. THE AWNING WILL ATTEMPT TO CLOSE.
KEEP HANDS CLEAR OF HARDWARE AND ROLL TUBE.
USE EXTREME CARE. SPRINGS UNDER TENSION
ARE DANGEROUS. IF NOT CONTROLLED THEY WILL
UNWIND QUICKLY. KEEP HANDS AND CLOTHING
CLEAR OF SPRING HEAD ASSEMBLY, AS PERSONAL
INJURY MAY RESULT.
5. Remove the cotter pin that is holding factory preset
tension. The cotter pin is found in the roll tube end cap
(Fig.6). For easier removal, twist the roll tube as if extending
the awning while pulling on the cotter pin.
6. Discard pin and repeat for other end. The support arms
will now be free to move due to release of the spring
tension. Maintain control of the support arm and place
against the unit wall. Push the support arms up until the
end cap pushes against the channel of the awning rail.

5
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
Fig.8
Fig.9
NOTE: For berglass and aluminum sidewall units with
backer material, drill four ⁄" diameter holes, apply sealant
and secure the support arm assembly using four #10 - 12 x
1" fasteners (Fig.8). Repeat for other end.
NOTE: For berglass and aluminum sidewall units without
backer material, drill four holes using a ⁄" drill bit. Apply
sealant and secure the support arm assembly using ⁄"
diameter molly rivets (Fig.9).
3. Place the protective bumpers on the awning rail, just
below the awning rail channel, behind the roll tube end
cap on each end. Let the roll tube end caps rest on these
bumpers. (Fig.10).
protective
bumper
Fig.10
Installation of Pull Strap Bracket
NOTE: Prior to installation please check the following
clearance. In order for the pull strap bracket to work
properly, clear wall space of 41" is needed for the standard
arm (18") and 65" is needed for the XL arm (33"). This
measurement is taken from the channel of the awning rail
(located approximately 3" above the window frame) to a
position downward on the unit wall. This measurement
is especially critical on window awnings located on slide
room windows.
1. Open the awning to its full extension by pulling down on
the pull strap.

6
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
3. Apply sealant and install pull strap bracket with two
#10 - 12 x 1" fasteners or molly rivets as needed (Fig.12).
4. To secure the awning, locate the pull strap and hook the
end into the pull strap bracket (Fig.13).
Fig.11
Fig.12
Fig.13
2. Center the strap in the awning. Move the loop of the pull
strap toward the unit and under the windowsill to locate the
placement of the pull strap bracket. Mark the location
(Fig.11). The valance should be hanging straight down.
MAKE SURE AWNING IS PULLED TAUT BY THE PULL
STRAP WHEN POSITIONING THE PULL STRAP BRACKET.

7
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
Operation
To Open Window Awning
1. Grasp the loop on the pull strap and pull down to extend
the awning then hook the loop onto the pull strap bracket
(Fig. 14).
To Close Window Awning
1. Remove the pull strap from the pull strap bracket (Fig.15).
Fig.14
1. Remove the #10 - 12 x 1" fastener from the support arm
and lift the spring head assembly out of the support arm on
both sides (Fig.16).
remove
fastener
2. To load tension on the torsion spring, turn the spring
head assembly as shown in (Fig.17 and Fig.18).
Fig.15
Fig.16
Right End Cap -
Turn counterclockwise
Left End Cap -
Turn clockwise
Fig.17 Fig.18
DO NOT RELEASE STRAP AS WINDOW AWNING IS UNDER
TENSION AND MAY SNAP BACK AGAINST THE UNIT.
2. Slowly allow awning to retract to closed position by
feeding the pull strap upwards at a 45-degree angle. This
prevents the strap from building up and creating a bulge in
the fabric.
3. The awning is now ready for travel with no further
locking required.
Loading the Tension
NOTE: If the Solera® Window Awning does not have cotter
pins holding the pre-wound spring head assemblies, then
tension must be added.
USE EXTREME CARE. SPRINGS UNDER TENSION ARE
DANGEROUS. IF NOT CONTROLLED THEY WILL UNWIND
QUICKLY. KEEP HANDS AND CLOTHING CLEAR OF TOP
CASTING, AS PERSONAL INJURY MAY RESULT.

8
Solera®
Window Awning
Installation and Owner’s Manual
(For Aftermarket Application)
lci1.com 574-537-8900 Rev: 03.30.18
CCD-0001283
4. When facing the awning, the spring head assembly on
the right is to be turned counterclockwise. The spring head
assembly on the left is to be turned clockwise.
NOTE: There are arrows on both end caps indicating the
correct direction to turn the springs (Fig.20).
5. Turn the spring head assembly as specied and insert
cotter pins. Carefully insert the spring head assembly back
into the support arm assembly, secure with a #10 - 12 x 1"
fastener. Repeat for the other side. Remove cotter pins.
Maintenance
Fabric Care
If the awning is retracted while wet, extend the awning and
let it dry as soon as conditions allow before retracting it
again. This will help prevent the formation of mildew and add
greatly to the life of the awning. Mildew does not form on the
fabric itself, but on the accumulated dust, dirt and grime.
NOTE: Periodically clean vinyl or woven acrylic fabric
using a mixture of ¼cup of dish soap and 5 gallons of
warm water. Liberally apply the mixture on the top of the
fabric and retract the awning for 5 minutes. This will apply
the mixture to the bottom of the fabric as well. Extend the
awning and hose off with fresh water. Repeat if necessary.
Allow to dry before retracting.
3. Refer to the chart (Fig.19) for the number of turns
required for the awning size.
Size Turns
156-192" 16
144" 14
132" 14
120" 13
108" 13
96" 13
90" 13
84" 12
72" 12
66" 12
60" 11
54" 10
48" or less 9
arrow
Manual information may be distributed as a complete
document only, unless Lippert Components provides
explicit consent to distribute individual parts.
All manual information is subject to change without notice.
Revised editions will be available for free download at
lci1.com. Manual information is considered factual until
made obsolete by a revised version.
Please recycle all obsolete materials and contact Lippert
Components with concerns or questions.
Fig.19
Fig.20