Lippert Components Jack-It User manual

1
Jack-It™
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 02.17 - Jack-It™ Aftermarket Manual
Jack-It™
Aftermarket
Manual
Table Of Contents
Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
Safety Requirements � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
Resources Required � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Installation Instructions � � � � � � � � � � � � � � � � � � � � � � � � � 2
Securing Bikes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Patent protected, trademarked, and produced by Let’s Go Aero, Inc.
Corporate Ofce: 4474 Barnes Road, Colorado Springs, CO 80917 USA.
Made in China.
US Patent Numbers: 8,899,456, D717,716, D717,717, D684,917, D722,289,
patents pending.
Introduction
The Jack-IT™ is a bicycle rack designed to attach to your RV.
Additional information about this product can be obtained from
www.lci1.com/support or by downloading the free myLCI app.
The app is available on iTunes® for iPhone® and iPad® and
also on Google Play™ for Android™ users.
iTunes, iPhone, and iPad are registered trademarks of Apple
Inc. Google Play and Android are trademarks of Google Inc.
Lippert Components, Inc. recommends that the following
inspections, troubleshooting, component replacement and
verications be completed only by certied RV technicians.
Safety Requirements
Failure to follow the instructions provided in this
manual may result in death, serious injury, vehicle
damage or voiding of the component warranty�
Moving parts can pinch, crush or cut� Keep clear and
use caution�
The use of this product while bicycles are loaded may
affect the turning radius on some vehicles� Check the
turning radius before travel�

2
Jack- It™
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 02.17 - Jack-It™ Aftermarket Manual
Resources Required
9/16” Socket Wrench
3/4” Socket Wrench
Installation Instructions
1� Remove the tongue jack from the coupler. Position the
PowerTower™ (Fig�1G) on the coupler. Place the
tongue jack on the PowerTower (Fig�1G) and secure
both to the coupler using 3 nuts, bolts and washers each
(Fig�1H, 1I and 1J).
Note: If there is no tongue jack, attach the PowerTower
(Fig�1G) to the coupler on the front of the trailer using 3
nuts, bolts and washers each (Fig�1H, 1I and 1J).
2� Attach the stinger (Fig�1F) to the PowerTower
(Fig�1G) using the NoMotion™ pin and washers
(Fig� 1C, 1D and 1A). For safety, insert the cotter pin
(Fig�1B) through the hole at the end of the NoMotion pin
(Fig�1C) after tightening securely.
3� Attach the base (Fig�1E) to stinger (Fig�1F) using the
NoMotion pin and washers (Fig�1C, 1D and 1A). For
safety, insert the cotter pin (Fig�1B) through the hole at the
end of the NoMotion pin (Fig�1C) after tightening securely.
A
B
C
D
E
F
G
H
I
J
Fig�1

3
Jack- It™
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 02.17 - Jack-It™ Aftermarket Manual
Note: Several hole positions are provided for
cradles (Fig�2A). Pads (Fig�2D) and
SwayStop™ pins (Fig�2F) slide along the
length of the wings (Fig�2G).
4� Slide one SwayStop pin (Fig�2F) onto each
wing (Fig�2G) from the bottom so that the
SwayStop locates between the snap pin
(Fig�2H) and the pad (Fig�2D).
Note: A 2nd and optional SwayStop pin is
provided to secure both wheels of the bike to
the rack, install at this time if desired.
Note: If not using the 2nd and optional
SwayStop pins then the SwayStop pins
(Fig�2F) should point in opposite directions.
5� Attach wings (Fig�2G) to base (Fig�2E)
using 2 snap pins (Fig�2H).
6� Install 6 rubber straps (Fig�2B): 1 onto
each cradle (Fig�2A) and 1 onto each
SwayStop pin (Fig�2F).
7� Attach 4 cradles (Fig�2A). Attach 2 to each
wing (Fig�2G), securing with cotter pins
(Fig�2C). Attach 1 on each wing facing the
tow vehicle and 1 on each wing facing the
trailer.
Note: Adjustment will be necessary depending
on the size and desired position of the
bicycles.
A
B
C D E
F
G
H
B
B
Fig�2

4
Jack- It™
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 02.17 - Jack-It™ Aftermarket Manual
Manual information may be distributed as a complete
document only, unless Lippert Components provides explicit
consent to distribute individual parts.
All manual information is subject to change without notice.
Revised editions will be available for free download at www.
lippertcomponents.com. Manual information is considered
factual until made obsolete by a revised version.
Please recycle all obsolete materials and contact Lippert
Components with concerns or questions.
NotesSecuring Bikes
1� For 2 bicycles, the best technique is to position the bicycles
front to back/back to front with the chain ring to the outside.
2� Hang 1 bicycle on the tow vehicle side of the bicycle rack, so
the top of the wheels are each supported by a cradle.
3� Secure by tensioning each rubber strap over the top of each
tire and engaging a strap hole with the end of the cradle.
4� Use 1 SwayStop pin to secure at least 1 wheel below the
frame where the wheel crosses the wing using the same
technique with the stop pin rubber strap (Fig�3). A second
and optional SwayStop pin is provided to secure both wheels
of the bike to the rack if desired.
5� Repeat for a 2nd bicycle on the trailer side of the bicycle rack.
Fig�3
Always make sure all connections between the bicycle
rack and the trailer coupler are secure/tight/ready for
travel� Always make sure the bicycles are securely
attached to the bicycle rack before driving�