Lippert Components OneControl Tank Monitor V1 User manual

OneControl® Tank
Monitor V1 Controller
OEM INSTALLATION MANUAL

Rev: 06.12.19 Page 2 CCD-0002310
Introduction
The OneControl® Tank Monitor can be used to monitor up to 9 tanks — 7 water tanks and 2 fuel tanks. The
tank monitor also has 4 latching relays that can be used to operate other devices, such as an electric water
heater, gas water heater, water pump, or water tank heater.
Safety
Resources Required
TABLE OF CONTENTS
Introduction 2
Safety 2
Resources Required 2
Installation 3
Harness 3
Resistor Pack 4
Operation 5
OneControl®Control Panel 5
Wiring Diagram 6
Notes 7
The “WARNING” symbol above is a sign that an installation procedure has a safety risk involved
and may cause death, serious personal injury, severe product or property damage if not performed
safely and within the parameters set forth in this manual.
Moving parts can pinch, crush or cut. Keep clear and use caution.
• Cordless or electric drill or screw gun
• Appropriate drive bits
• #8 x 1" wood screws

Rev: 06.12.19 Page 3 CCD-0002310
Fig. 1
Installation
1. Mount tank monitor controller (Fig. 1) by securing to a solid surface with #8 x 1" wood screws or
equivalent.
NOTE: An ideal location can be chosen by the OEM.
2. Connect to DC 12 V power and ground.
3. Connect CANBUS Data wires (in proper sequence with MyRV system components).
4. Connect tank wire harness.
5. Connect the first tank's sensor resistor pack signal wire to proper (tank) input on harness (Fig. 8).
6. Repeat steps for each tank.
Harness
NOTE: Tanks 1-7 are reserved for water tanks sensors. Tanks 8-9 are for fuel tank sensors only. Ignition FEED
is for gas water heater ignition feedback (Fig. 2) and (Fig. 3).
NOTE: All harness wires are 18 g. minimum.
Fig. 2 Fig. 3
9
8
7
6
1
2
3
4
5Ignition Feed

Rev: 06.12.19 Page 4 CCD-0002310
Resistor Pack
• White – Ground(-) connect to EMPTY (E) sensor
• Yellow – connect to LOW level (⁄) sensor
• Green – connect to MID level (⁄) sensor
• Red – connect to FULL level (F) sensor
• Pink – signal wire connects to “Tank” wire from monitor harness. This wire is connected to the proper
input wire on the panel harness.
NOTE: The sensors are connected to the yellow, green, and red wires on the sensor resistor pack (Fig. 4). The
tank sensor resistor pack connects to the tank sensor with an eyelet being screwed down onto the
sensor.
Fig. 4

Rev: 06.12.19 Page 5 CCD-0002310
Fig. 5
Fig. 6 Fig. 7
A
A
Operation
OneControl®Control Panel
1. The control panel will operate various devices connected to the OneControl® system.
2. Locate “OneControl® Control Panel” (Fig. 5).
3. Pressing the “OneControl® Control Panel” (Fig. 5A) will open “OneControl® Applications”.
4. Pressing the "Tank Monitor" icon (Fig. 6A) will allow you to access the tank monitor screen (Fig. 7).
NOTE: The indicator panel light will be depicted by the use of the tank; a gray line for the gray tank, a blue
line for the blue tank, etc.
NOTE: Only the tanks used and configured will be displayed on the screen.
NOTE: Battery voltage is also displayed on the monitor panel screen (Fig. 7A).
A

Rev: 06.12.19 Page 6 CCD-0002310
Fig. 8
Wiring Diagram
Tablet
Wireless Hub

Rev: 06.12.19 Page 7 CCD-0002310
Notes

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).
LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an
authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.
The information contained in this manual is subject to change without notice and at the sole discretion of LCI.
Revised editions are available for free download from lci1.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Ph: [phone] | Web: lci1.com | Email: [email protected]