Lippert Components Quick Drop Tongue Jack Installation instructions

1
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
Table of Contents
Introduction ............................................ 2
Safety ................................................... 2
Resources Required ................................... 2
Parts List ................................................ 2
Installation .............................................. 3
Preparation ............................................. 3
Operation ............................................... 4
Power Tool Operation .................................. 4
Hitching To A Tow Vehicle ............................. 5
Manual Operation ..................................... 5
Unhitching From A Tow Vehicle ........................ 6
Notes ................................................. 6-8
Quick Drop
Tongue Jack®
Installation and
Owner’s Manual
(For Aftermarket Applications)
Quick Drop Tongue Jack Aftermarket Kit
Part # Description
733926
Quick Drop Tongue Jack; includes mounting bolts &
footpad replacement kit (PN 710633)

2
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
Introduction
The Quick Drop Tongue Jack is a hand-cranked, top-
winding mechanical jack that features a drive-nut option
to raise and lower the tongue jack leg with the use of an
electric drill. The Quick Drop Tongue Jack has a lifting
capacity of 2,000 lbs. Do not exceed the capacity limit.
The design of this tongue jack is as stable, strong and
efcient as the rest of LCI’s tongue jack products, while
offering a cost efcient and quicker set-up/tear-down
option.
Additional information about this product can be
obtained from lci1.com/support or by using the myLCI
app. Replacement components can be ordered from
https://store.lci1.com/ or by using the myLCI app.
The myLCI app is available for free on iTunes®for iPhone®
and iPad®and also on Google Play™for Android™users.
iTunes®, iPhone®, and iPad®are registered trademarks of
Apple Inc. Google Play™and Android™are trademarks of
Google Inc.
Safety
Read all instructions and safety labels before starting
installation of this product.
THIS SAFETY LABEL INDICATES THAT THE
FOLLOWING PROCEDURE MAY CREATE A
CONDITION WHERE SEVERE PRODUCT DAMAGE,
SERIOUS PERSONAL INJURY OR DEATH MAY
OCCUR IF STATED PRECAUTIONS ARE
NOT FOLLOWED.
Resources Required
• Cordless or electric drill or screw gun
• 9/16” socket
• ¾” socket
Parts List
MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP
CLEAR AND USE CAUTION.
Quick Drop Tongue Jack Aftermarket Kit Part # 733926
No. Part # Description Qty
A 423192 Quick Drop Tongue Jack 1
B 710633 Quick Drop footpad kit 1
A
B

3
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
Installation
1. Carefully slide the jack leg (Fig.2A) through the hole in
the coupler (Fig.2B) of the trailer’s A-frame (Fig.2C).
A
B
C
D
Fig.1
C
AB
Fig.2
2. Align the three holes in the Quick Drop Tongue Jack’s
mounting plate with the three holes in the coupler.
3. Secure the Quick Drop Tongue Jack to the coupler with
three supplied 3/8” - 16 x 1” bolts (Fig.3A).
4. Reattach the footpad to the jack leg by sliding the footpad
over the bottom of the jack leg and securing it with the
previously-removed clevis pin and hairpin cotter pin.
Fig.3
A
1. Make sure trailer is parked on level ground.
2. Chock all tires.
3. Support the trailer according to the manufacturer’s
recommendations.
4. Remove existing tongue jack from A-frame and properly
dispose of jack and old mounting hardware.
5. If necessary, remove footpad from the Quick Drop
Tongue Jack.
A. Remove the hairpin cotter pin (Fig.1A) from the clevis
pin (Fig.1B), which holds the footpad (Fig.1C) to the jack
leg (Fig.1D).
B. Set aside the hairpin cotter pin, clevis pin and footpad.
Preparation
NOTE: To operate the crank handle, it is required to have
an existing 6” to 6 ½” radius clearance from the center
point of the jack leg to the area around it.
THE TRAILER MUST BE SUPPORTED PER THE
MANUFACTURER'S RECOMMENDATIONS BEFORE
WORKING UNDERNEATH. FAILURE TO DO SO MAY
RESULT IN DEATH, SERIOUS PERSONAL INJURY OR
SEVERE PRODUCT OR PROPERTY DAMAGE.

4
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
FAILURE TO FULLY ENGAGE THE CRANK HANDLE
INTO THE STORED POSITION WHEN USING THE
POWER TOOL OPERATION MODE COULD CAUSE
PRODUCT DAMAGE OR PERSONAL INJURY.
Fig.4
USE OF A POWER TOOL WITHOUT A CLUTCHING
FEATURE AND OPERATED AT FULL SPEED WHILE IN
DRILL OVERRIDE MODE COULD CAUSE PERSONAL
INJURY OR DAMAGE TO THE TONGUE JACK’S DRIVE
NUT MECHANISM. THE DRIVE NUT MECHANISM CAN
BE STRIPPED IF THE POWER TOOL CONTINUES TO
BE OPERATED IN DRILL OVERRIDE MODE AFTER
THE JACK LEG IS RETRACTED/EXTENDED TO THE
FULLEST EXTENT.
DO NOT USE AN IMPACT TOOL TO TURN THE
TONGUE JACK DRIVE NUT. AN IMPACT TOOL
CAN OVERPOWER THE DRIVE NUT MECHANISM,
CAUSING DAMAGE TO THE TONGUE JACK AND
VOIDING THE PRODUCT WARRANTY.
FAILURE TO MAINTAIN POSITIVE CONTROL OF
THE CORDLESS DRILL DURING OPERATION MAY
CAUSE TORQUE TWIST TO OCCUR, INJURING THE
OPERATOR AND/OR DAMAGING EQUIPMENT.
A
B
Operation
Power Tool Operation
1. Make sure the crank handle is in its stored position
(Fig.4).
NOTE: When the crank handle is in its stored position, the
drive nut is raised up (Fig.4A), making it accessible for use
with a cordless or electric drill or screw gun. Do not use
an impact tool. An impact tool may cause damage to the
tongue jack drive nut screw mechanism.
2. Use a ¾” drive socket with either a cordless or electric
drill or screw gun.
A. Insert the drive socket over the hex head of the drive
screw (Fig.4A).
B. Rotate the drive screw in a clockwise direction to
extend the jack leg.
C. Rotate the drive screw in a counterclockwise direction
to retract the jack leg.
THE QUICK DROP TONGUE JACK HAS A LIFTING
CAPACITY OF 2,000 LBS. DO NOT EXCEED THIS
LIMIT OR SEVERE PRODUCT DAMAGE, SERIOUS
PERSONAL INJURY OR DEATH MAY OCCUR. KEEP
PEOPLE AND PETS AT A SAFE DISTANCE DURING
INSTALLATION AND OPERATION OF THE TONGUE
JACK.

5
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
extends
retracts
Fig.5
B
A
Manual Operation
NOTE: To operate the crank handle, it is required to have
an existing 6” to 6 ½” radius clearance from the center
point of the jack leg to the area around it.
1. Flip the crank handle (Fig. 5A) over into its cranking
position.
A. Rotate the crank handle clockwise to extend
the jack leg.
B. Rotate the crank handle counterclockwise to retract
the jack leg.
2. After desired tongue jack height is achieved, ip the
crank handle over into its stored position (Fig.4). The crank
handle will engage the ribs of the cap (Fig.4B).
NOTE: Since the crank handle moves independently of
the screw drive, storing it prevents the handle from turning
when the drive screw is used. Fig.6
A
Hitching To A Tow Vehicle
1. Chock the tires of the trailer.
2. Make sure the footpad of the Quick Drop Tongue Jack
is pinned securely in place with the clevis pin and hairpin
cotter pin (Fig.6A).
3. Use a ¾” drive socket with either a cordless or electric
drill or screw gun.
A. Insert the drive socket over the hex head of the drive
screw (Fig. 4A).
NOTE: It may be necessary to slightly raise the jack leg
to allow the coupler to clear the hitch ball. Rotate the drive
screw in a clockwise direction to extend the jack leg.
B. Rotate the drive screw in a counterclockwise direction
to retract the jack leg.
4. Latch the tow vehicle hitch and connect any wires,
chains or sway control that may be equipped between the
tow vehicle and the trailer.
5. Remove the tire chocks.
6. Make sure the leg of the Quick Drop Tongue Jack is fully
retracted before moving the tow vehicle.

6
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
Unhitching From A Tow Vehicle
1. Chock the tires of the trailer.
2. Make sure the foot pad of the Quick Drop Tongue Jack
is pinned securely in place with the clevis pin and hairpin
cotter pin (Fig. 6A).
3. Make sure the ground surface under the Quick Drop
Tongue Jack footpad is rm and level.
4. Make sure the crank handle is in its stored position
(Fig.4).
5. Unlatch the trailer coupler.
6. Use a ¾” drive socket with either a cordless or electric
drill or screw gun.
A. Insert the drive socket over the hex head of the drive
screw (Fig. 4A).
B. Rotate the drive screw in a clockwise direction to
extend the jack leg to clear the hitch ball.
7. Disconnect any wires, chains or sway control that may
be equipped between the tow vehicle and the trailer.
8. Move the tow vehicle a safe distance away from
the trailer.
Notes

7
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
Notes

8
lci1.com 574-537-8900 CCD-0001391 Rev:09.18.18
Quick Drop Tongue
Jack®
Installation and Owner’s Manual
(For Aftermarket Applications)
Manual information may be distributed as a complete
document only, unless Lippert Components provides
explicit consent to distribute individual parts.
All manual information is subject to change without
notice. Revised editions will be available for free
download at lci1.com. Manual information is considered
factual until made obsolete by a revised version.
Please recycle all obsolete materials and contact
Lippert Components with concerns or questions.
Notes