Lippert Components 260782 User manual

Rev: 01.26.2017 Page 1 TI-135
LINC WIRELESS TOUCH REMOTE - IDS
TI-135
ELECTRONICS
Configuring the Remote (260782)
1. Turn the remote on by pressing and releasing the large silver button
at the bottom of the unit (Fig. 1A). Pressing this same button five
times accesses the Configuration menu after the unit has been
configured previously.
2. Press the “Config” button on the touch screen to begin configuring
the remote (Fig. 2A). Using the arrow buttons at the bottom of the
screen, navigate to the specific items the remote will control (Fig.
3). When the name of the item appears in the middle of the screen,
press the large “Select” button.
3. Assign an item or “None” to each of the seven function spaces
available. A Confirmation screen will appear on the screen (Fig. 4).
Press “OK” to save the configuration or “Cancel” to edit the functions.
Syncing the Remote to the Receiver
1. To begin syncing the remote to the receiver, both the receiver
and the remote must have power (12V DC for the receiver and the
battery in the remote must have a charge).
2. Push and hold the black button on the receiver (Fig. 6A). While the
black button is depressed, push and release the “Light” button on
the remote (Fig. 5A).
NOTE: If close enough to the receiver, an audible “click” can be heard
verifying the receiver is programmed to the remote.
3. Release the black button on the receiver.
NOTE: To sync a second remote to the receiver, repeat Steps 2 and 3.
Only sync two remotes per receiver.
For wiring diagram, see TI-091.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
A
A
A
A

Rev: 01.26.2017 Page 2 TI-135
LINC WIRELESS TOUCH REMOTE - IDS
TI-135
ELECTRONICS
Remote Operation Instructions
1. Turn the remote on by pressing and releasing the large silver button
at the bottom of the unit (Fig. 1A; Pg. 1).
2. Press the “OK” button on the touch screen to access the Function
Menu (Fig. 7A). The first page of the Function Menu has buttons for
the security light and functions 1-3. Functions 4-7 are located on the
second page of the menu and can be accessed by pressing on the
“Next" button at the top of the screen (Fig. 8A). The function buttons
correspond to the same names as the functions selected during
configuration. Most screens will have left and right arrow buttons
at the bottom of the screen. The left button will retract the slide or
awning. The right button will extend the slide or awning. Press and
hold either button until the item is fully retracted or extended. The
icon at the top of the screen will animate to show the action (Figs. 9
& 10). Otherwise, the button will state its function (Fig. 11).
3. After the desired operations are complete, the remote can be
powered down by pressing and holding the large silver button at
the bottom of the unit or will automatically turn itself off after 2
minutes of non-use.
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Function 1 (-)
Function 1 (+)
Function 2 (-)
Function 2 (+)
Function 3 (-)
Function 3 (+)
Function 4 (-)
Function 4 (+)
Light
Manual
Switches (+)
Manual
Switches (-)
Function 7 (+)
Function 7 (-)
Function 6 (+)
Function 6 (-)
Function 5 (+)
Function 5 (-) Power (-)
Power (+)
As a supplier of components to the RV industry, safety, education and customer satisfaction are our primary concerns. Should you
have any questions, please do not hesitate to contact us at [phone] or by email at [email protected]. Self-help tips,
technical documents, product videos and a training class schedule are available at www.lci1.com or by downloading the MyLCI app.
A
A