Lippert Flow Max RV User manual

TI-478 CCD-0007863
REV: 09.19.2023
Flow Max RV Toilet
Seat Assembly Kit
Installation Guide

TI-478 CCD-0007863REV: 09.19.2023 Page 2
A
D
E
Enlongated Seat Assembly Kit (2022121972)
Letter Part # Description Qty.
A2020221050 Lid and Seat Assembly 1
B2021106 603 Flathead Screw, 1/4-20 X 1.75 2
C2021106621 Adjustable Seat Block 2
D2020221051 Toilet Seat Base 1
E2021106608 Expanding Seat Nut, 0.72 X 1.50 2
C
B
Parts List

TI-478 CCD-0007863
REV: 09.19.2023 Page 3
Preparation
NOTE: Only use FlowMax Seat Assembly Kit on the FlowMax Toilet to ensure it is the
proper size and completely functional.
1. Before removal, clean the old seat as well as the toilet bowl and rim.
2. At the back of the bowl, locate lever (Fig. 1A) on the back of the seat assembly.
A
Resources Required
∆ Phillips screwdriver
∆ Flat blade screwdriver
∆ Adjustable wrench
∆ Hose clamp (if necessary)
∆ Side-cut pliers
NOTE: Figure 1 shows the back of the FlowMax Toilet. On the left, the back of the
toilet and water inlet is shown. On the right, the back of the toilet has been removed
to better show the lever (Fig. 1A).
Fig.1

TI-478 CCD-0007863REV: 09.19.2023 Page 4
3. Slide lever to the left to unlock the seat.
4. While lever is to the left, pull seat (Fig. 2A) towards the front of the FlowMax
bowl and away. This will allow the seat to slide o.
5. Use a screwdriver to remove Flathead Screws (Fig. 2B) from the seat base
assembly.
Fig.2
B
A
B

TI-478 CCD-0007863
REV: 09.19.2023 Page 5
6. Remove the rest of the seat assembly:
A. Toilet Seat Base (Fig. 3A)
B. Adjustable Seat Blocks (Fig. 3B)
C. Expanding Seat Nuts (Fig. 3C)
7. Appropriately dispose of the old seat.
Fig.3
B
AB
C
C

TI-478 CCD-0007863REV: 09.19.2023 Page 6
Installation
1. Remove new seat from packaging.
2. Install the seat assembly pieces as follows:
A. Expanding Seat Nuts (Fig. 4A)
B. Toilet Seat Base (Fig. 4B)
C. Adjustable Seat Blocks (Fig. 4C)
D. Flathead Screws (Fig. 4D)
3. Tighten Flathead Screws with a screwdriver to secure toilet seat base to
FlowMax Bowl (Fig. 4E).
4. Apply the lid and Seat Assembly (Fig. 4F) by sliding it onto and over the
installed Toilet Seat Base.
5. Listen for a clicking sound once it is locked into place.
Post-Installation Checks
1. Open and close the lid making sure it completely closes over the seat.
2. Jiggle the seat to conrm that it is secure.

TI-478 CCD-0007863
REV: 09.19.2023 Page 7
Fig.4
F
E
DD
C C
A A
B

Manual information may be distributed as a
complete document only, unless Lippert provides
explicit consent to distribute individual parts.
All manual information is subject to change without
notice. Revised editions will be available for free
download at lippert.com. Manual information is
considered factual until made obsolete by a revised
version.
Please recycle all obsolete materials and contact
Lippert with concerns or questions.
Whenever, wherever, we make
your experience better.
www.lci1.com
LippertNOW
LippertNOW
TI-478 CCD-0007863
REV: 06.28.2023