Lisle Digidown RDL User manual

V0.12
@ 2020 Lisle Design Ltd
Digidown® RDL
Quick Installation Guide
Using the Comprehensive Cable Kit

A
Tachograph original cable has separate
Yellow and White connectors
A1
A
2
Insert pre
-
activated SIM
, aerial
and screw case
together
Disconnect White connector from tachograph
A
3
A
4
If present,
disconnect Brown and Red connectors from
tachograph. Do not disconnect Yellow connector.
Connect Brown, Red and White connectors of RD
Cable into tachograph. Yellow connector and socket of
RD Cable will be left unused.
A
5
A
6
If present, reconnect Brown and Red connectors into
female sockets of RD Cable
Reconnect White connector into female socket of
RD Cable
A
7
A
8
Connect other end of
RD
Cable
in
to Digidown RD
and
C
heck that
the
Power ED is ON
and the Tacho and
Network EDs in the table below. Fix the Digidown
RD securely to the vehicle
Digidown
RDL
Ma not be
present
Digidown
RDL
Ma not be
present
RDL cable
Not
required
Ma not be
present
Ma
not be
present
Ma not be
present
Original cables
Tachograph
Separate
Connectors
Ma not be
present
Network
Power
Tacho

B
Original Tachograph Cable
has a Double connector
B
1
B
2
Insert pre
-
activated SIM
, aerial
and screw case
together
Disconnect
D
o
uble
connector from tachograph
B
3
B
4
If
present, disconnect Brown and Red connectors from
tachograph
Connect Brown, Red
,
Yellow
and White connectors of
RD Cable into tachograph
B
5
B
6
If present, reconnect Brown
and Red connectors into
female sockets of RD Cable
Reconnect
Double
connector into female
Yellow and
White sockets of RD Cable
B
7
B
8
Connect other end of
RD
Cable
in
to Digidown RD
and
C
heck that
the
Power ED is ON
and the
Tacho and
Network EDs in the table below. Fix the Digidown
RD securely to the vehicle
Status
Power
Original cables
Double
Connector
Tachograph
Ma not be
present
RDL cable
Ma not be
present
Ma not be
present
Digidown
RDL
Ma not be
present
Ma not be
present
Ma not be
present
Digidown
RDL
Network
Power
Tacho

Important: If a tachograph seal is present, we recommend the unit is fitted at a workshop
LED Light Indicates Suggested Action
acho
ON System is starting Wait a few moments
OFF OK -
Flashing x1 Tachograph comms
failure
(1) Check connections
(2) Check tachograph is compati le with
Remote Downloading
Flashing x2 Tachograph
parameters error
Ena le Remote Downloading parameter
setting in tachograph
Network
ON System is starting Wait a few moments
OFF OK -
Flashing x3 SIM Card not found Check SIM Card is installed correctly
Flashing x4 Network not found (1) Check aerial is installed correctly
(2) Check reception in area
Flashing x5 No network signal (1) Check aerial is installed correctly
(2) Check SIM has een activated
Flashing x6 Network registration
error (1) Check SIM has een activated
Flashing x7 APN error (1) Check APN y sending SMS: Get APN
(2) Set new APN y sending SMS: Set APN
Flashing x8 Hardware error Get in touch with your distri utor
Configuration y SMS Commands
Get APN
SMS o SIM phone num er
SMS Message
DIGIDOWN_GET_APN
Reply
Vehicle_Identifier: <apn carrier="SIM Provider",apn="APN
Address",user=" APN User",password="APN Pass"/>
Set APN
SMS o SIM phone num er
SMS Message
DIGIDOWN_ ET_APN=: <apn carrier="SIM Provider",apn="APN
Address",user=" APN User",password="APN Pass"/>
Reply
Vehicle_Identifier: OK
@ 2020 Lisle Design Ltd
New Technology Centre, North Haugh, St. Andrews KY16 9SR, Scotland
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.lisledesign.com