Living Earth Crafts Contour User manual

Contour Pedicure Line
USER MANUAL
1-400-00XX • Rev A • X/X/XX
© Living Earth Crafts 2017, All Rights Reserved
*shown with oponal accessories and/or nishes
Contour LX
Contour

© Copyright 2016
Living Earth Cras®
All rights reserved. is document or any
portion thereof may not be reproduced
in any way, including photocopying or
translation to another language without
the prior written permission from Living
Earth Cras.
Living Earth Cras® is a registered trade-
mark of Earthlite Massage Tables, Inc.
Legal Notice
e information provided in this document is intended
for informational purposes only and is subject to change
without notice. e information provided in this docu-
ment should not be construed as a commitment by
Living Earth Cras®.
Living Earth Cras® assumes no responsibility for the
accuracy or suitability of the information contained in
this document. is document may contain technical
inaccuracies or errors. Living Earth Cras® makes no
expressed or implied warranties of any kind concerning
the information contained in this document, including,
but not limited to, the implied warranties of merchant-
ability and tness for purpose.
Living Earth Cras® shall not be liable for incidental or
consequential damages in connection with or arising out
of the product, performance, or use of this document
and the information and material it describes.
Introduction
Congratulaons on your purchase of the Contour pedicure chair. The Contour oers an
unparalleled pedicure and hydrotherapy experience, featuring a luxurious, handcraed
motorized chair and a tub powered by the patented Sanijet® pipeless jets. The tub basin is lined
with soothing textured foot pebbles to give your client’s feet a relaxed, massaging sensaon.
The Contour is designed for licensed therapists and technicians and is intended to be used in a
professional spa, salon, or similar commercial environment. While no special training is needed
to operate the product, for safety reasons it is important that the instrucons contained in this
manual are reviewed in detail before the rst use. This manual should be read in its enrety by
each professional who will be operang the product to ensure the safety of both operator and
client. This manual should be saved for future reference.
The Contour should not be used in any other manner than described in this manual. Please read,
understand, and follow all safety warnings, labels, and instrucons. Misuse, use of unnecessary
force, or using the chair for unintended or unauthorized procedures can result in injury to
operator, client, and/or equipment.
Detailed instrucons for use and maintenance can be found in this user manual. If you have
further quesons, please contact us at [phone] for US customers, or [phone] for
internaonal customers. We can also be reached via e-mail at info@livingearthcras.com
Secon 1: Safety Informaon
Safety Symbols/Warnings
Secon 2: Product Overview
Product Diagram
Product Specicaons
Secon 3: Operang Instrucons
Control Panel Operaon & Electric Back Tilt
Jets & Lights
Water Fill Valve, Drain & Discharge Pump
Relaxor
Secon 4: Care & Maintenance
Cleaning Jets
Ongoing Maintenance
Troubleshoong
Electrical Specicaons
Warranty Informaon
FAQs
Contact Us
2-3
4
5
6
7
8
9
10
11
12
13
14
15
back cover
Table of Contents

SECTION 1: SAFETY INFORMATION
Safety Symbols ALERT
Indicates a potentially hazardous
situation which could result in
equipment damage and/or injury.
Familiarize yourself with the following Safety &
Warning symbols. They are designed to prevent
damage and injury to you, your clients, and your
new Living Earth Crafts product.
ATTENTION
Consult accompanying documents
CAUTION
Indicates a potentially hazardous
situation which may result in minor or
moderate injury.
DANGER
Indicates an imminently hazardous
situation which will result in serious or
fatal injury - used in extreme conditions.
WARNING
Indicates a potentially hazardous
situation which could result in serious
injury.
Important Information About Safety Instructions
The important safety instructions and warnings in this manual cannot cover all possible problems and conditions
that can occur. Use common sense and caution when installing, operating, or maintaining this appliance.
WARNING - RISK OF ACCIDENTAL INJURY OR DROWNING. DO NOT
USE DRUGS OR ALCOHOL BEFORE OR DURING USE. CHILDREN OR
HANDICAPPED PERSONS SHOULD NOT USE WITHOUT SUPERVISION.
WARNING - RISK OF HYPERTHERMIA AND POSSIBLE DROWNING. WATER
TEMPERATURE IN EXCESS OF 38°C or 100.4°F CAN BE INJURIOUS TO YOUR
HEALTH. CHECK AND ADJUST WATER TEMPERATURE BEFORE USE.
READ AND SAVE THESE INSTRUCTIONS
SECTION 1: SAFETY INFORMATION
INSTALLATION INSTRUCTIONS / GROUNDING INSTRUCTIONS
WARNING - When using electrical products, basic precautions should always
be followed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK. Connect only to a circuit protected
by a ground-fault circuit-interrupter.
2. Grounding is required. The unit should be installed by a qualifi ed service
representative and grounded.
This product must be grounded. If it should malfunction or break down, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock. This product
is equipped with a cord having an equipment-grounding conductor and grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Improper connection of the equipment-grounding connector can result in a risk of electric shock.
Check with a qualifi ed electrician or serviceman if you are in doubt as to whether the product is
properly grounded. Do not modify the plug provided with the product - if it will not fi t the outlet,
have a proper outlet installed by a qualifi ed electrician.
READ AND SAVE THESE INSTRUCTIONS
23
IMPORTANT SAFETY INSTRUCTIONS - FOR COMMERCIAL USE ONLY
Read all instructions before using the Contour pedicure chair.
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above
the body temperature of 98.6°F or 37°C. The symptoms of hyperthermia include an increase in the internal
temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include:
a) Failure to perceive heat,
b) Failure to recognize the need to exit the hydromassage bathtub,
c) Unawareness of impending hazard,
d) Fetal damage in pregnant women,
e) Physical inability to exit the hydromassage bathtub, and
f) Unconciousness resulting in the danger of drowning. WARNING - The use of alcohol, drugs, or medication
can greatly increase the risk of fatal hyperthermia.
WARNING - RISK OF ELECTRIC SHOCK - Do not permit electric appliances (such as hair dryers,
lamp, telephone, radio, or television) to be within 5 ft (1.5m) of this unit.
WARNING - RISK OF INJURY - Exercise care when using a foot bath. Use this product for its intended
purpose: a manicure chair and fi ll and drain indoor commercial appliance for foot and ankle hydro massage.
DO NOT use attachments not recommended by manufacturer.
WARNING - MOVABLE PARTS, RISK OF INJURY:
• Keep children away from adjustable seat armrests, tilt back, and seat slide, and footrest.
WARNING - To reduce the risk of burns, fi re, electric shock, or injury to persons:
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled
persons. DO NOT leave children alone or allow them to operate the controls. Keep controls out of reach
of children. DO NOT allow children to crawl behind the chair.
• Never use this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination
and repair.
• Keep the cord away from heated surfaces.
• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, etc.
• Never drop or insert any object into any opening.
WARNING
• DO NOT reach for any electrical object that has fallen into the water. Unplug immediately.
• DO NOT drop or insert anything into jet opening.
• DO NOT operate without the complete jet assembly installed or without water fi lled 1 inch above jets.
• DO NOT overfi ll the basin.
• DO NOT stand on or in the basin, or on the foot rest.
• DO NOT leave this appliance unattended when in operation.
• DO NOT use outdoors.
• Keep the electrical cord away from heated surfaces.
• Connect this appliance only to a properly grounded outlet.
• To avoid injury, exercise care when entering or exiting the chair and foot bath.
• Use caution when making positioning adjustments to your chair. Keep all equipment and body parts
away from moving parts while making any adjustments.
• It is important that you clean and disinfect the jets and basin after every use.
• Hydrotherapy should be pleasant and comfortable. Should you or a client experience any pain or
discomfort while using the foot bath, discontinue use immediately and consult a physician.
• You or your clients should consult a physician if diabetic, have poor circulation, if feet or legs are in-
fl amed, have an open wound, or if you have questions about whether you should be using hydro mas-
sage equipment.
• A qualifi ed plumber and electrician are strongly recommended to install your foot bath.
• Make certain that the cord and plug are maintained in good condition and are not allowed to become
damaged while in use. Avoid positioning the cord in the traffi c lane and it is always kept out of the way.
Take this furnishing out of service immediately if the cord or plug becomes damaged in any way.
• Do not attempt to repair. All repairs must be performed by an authorized service representative.
See Installation Manual for full
installation instructions

SECTION 2: PRODUCT OVERVIEW
*Measurements may vary due to natural material varia ons.
45
Feature Standard Op onal
Sanijet Pipeless Jets X
Re exology Fiberglass Tub X
Fully Motorized Seat and
Footrest X
Motorized Retractable
Armrest Doors X
Embedded Control Panel X
Power Drain/Discharge
Pump X
Relaxor® Heat & Massage X
Side Trays X
ADA Compliant X
Avonite Standard Op ons Upraded Op ons
Upholstery Naturso ™ Promessa® or
Ultraleather®
Included Features
Product Specications
Overall Width 32.5” (78.7 cm)
Shroud Width 22” (55.8 cm)
Shroud Height 15” (38.1 cm)
Length (armrest doors open) 73” (185.4 cm)
Length (armrest doors closed) 57” (144.8 cm)
Armrest Door Height 29.25” (74.3 cm)
Seat Height 21” (53.3 cm)
Backrest Cushion
Pillow
Armrest Door
Shroud
Drain Handle
Seat Cushion
Sprayer/Fill
Water Fill
Valve
Control Panel
*Chair shown with op onal  nishes
SECTION 2: PRODUCT OVERVIEW
Footrest
Light
Tub Basin
Discharge Pump
Button (Optional)
Side Tray
(Optional)

SECTION 3: OPERATING INSTRUCTIONS
Control Panel Operation
Slides seat fully
forward & opens
armrest doors
Your Contour control panel is connected and ready for use. See below for descripons of
each buon funconality. For the top row of buons, push and hold the buon unl the
chair movement stops - this means you have reached the memory posion. For the lower
set of buons, push and hold unl the desired posion is reached.
WARNING
Always use extreme cauon when making any posion adjustments to your chair.
Ensure all body parts and objects are clear from all moving parts.
6
SECTION 3: OPERATING INSTRUCTIONS
7
Closes armrest
doors
Seat memory
position 1*
(appx 2” back from
“open” position)
Seat memory
position 2*
(appx 4” back from
“open” position)
Raise
Footrest
Lower
Footrest
Slide Seat
Backward*
Slide Seat
Forward
Chromasoothe Light
Sanijet® Pipeless Jets
Pressing the On/O buon once will start the jets, and pressing the buon again will turn the
system o. Turn on the jets ONLY AFTER the tub is lled with water, and ensure you turn the
jets OFF before draining the tub.
CAUTION
Running the jets without lling the tub with water can damage or destroy the jets.
Ensure that a MINIMUM of one (1) inch of water is above the jets prior to use.
Pressing the light buon once will turn the light to the default Bright White color. Press the
switch again to cycle to the next color mode, in the following order:
1. Bright White
2. Aqua Blue
3. Soothing Blue
4. Ocean Blue
5. Majesc Gold
6. Shamrock Green
7. Fiery Red
8. Chameleon Mode
9. Party Mode
To reset, turn lights o for 5 seconds and turn back on. Lights will ash 4 mes and return to
Bright White.
Electric Back Tilt
The electric back lt buons are conveniently located on the inside of the le armrest door,
where clients can easily make lt adjustments themselves. See below for descripons of buon
funconality.
*NOTE
If the “Slide Seat Backward”, “Seat memory posion 1”, or “Seat memory posion 2” buons
aren’t working, ensure the armrest doors ARE FULLY CLOSED. These buons will not acvate if the
armrest doors are at all open. Posions are preset at factory and cannot be changed.
Decrease Seat
Back Tilt
Increase Seat Back Tilt
Jets On/O Button Chromasoothe Light
Button
Increase Seat
Back Tilt

SECTION 3: OPERATING INSTRUCTIONS
8
SECTION 3: OPERATING INSTRUCTIONS
9
Discharge Pump (Optional)
Drain Knob
Turn the drain knob clockwise to close the drain when lling the tub. Turn the knob
counterclockwise to open the drain and empty the tub.
Water Fill Valve
CAUTION
There is no automac shuto with the water ll valve. You MUST turn the valve OFF
aer the tub is lled to prevent overow and/or ooding. Do not walk away from the
tub when it is lling with water.
Down-OffUp-FillLeft-Cold Right-Hot
The water ll valve is OFF when poinng DOWN. Water dispenses when you pull the valve UP.
Hot water is dispensed when the valve is turned to the RIGHT. Cold water is dispensed when
the valve is turned to the LEFT.
Relaxor® Heat & Massage (Optional)
The following diagrams illustrate the ease-of-use and funconality that the Relaxor® system
provides to you and your clients.
SELECT
WA
VE
PULSE
Ultra
PWR
LO HI
1
2
3
Power
Lower Back Heat - High
Lower Back Heat - Low
Massage All Zones - Connuous
Massage All Zones - Sequenal
Massage All Zones - Short Bursts
Raise Massage Intensity
Raise Massage Speed
Upper Back Massage
Mid Back Massage
Low Back Massage
Lower Massage Intensity
Lower Massage Speed
DANGER - RISK OF ELECTRIC SHOCK
Keep hand control and all electrical components away from water.
PWR
PWR
• Massage 15 Minute Timer (Standard)
• Massage 30 Minute Timer (Hold Down Button)
• Indicates Active Button
• Indicates Normal Standby
• Indicates High Mode
• Indicates Low Mode
Green Light
Blue Light
Red Light
Orange Light
Symbol Description
Discharge pump buon is locaon directly above the drain knob. Before pressing the buon,
open the drain with the drain knob and let the water start draining towards the pump. Wait
approximately 5-10 seconds for the pump to register, then push the discharge pump buon.
Discharge
Pump
On/O Buon
Drain Knob

SECTION 4: CARE & MAINTENANCE
10
SECTION 4: CARE & MAINTENANCE
11
Cleaning Sanijet® Pipeless Jets
Preparation & Cleaning
1. Drain the bath of all water.
2. Rotate the jet covers to unlock. (Fig. 1)
3. Remove the jet covers. (Fig. 2)
4. Remove the magnec impellers/rotors from the jet case. (Fig. 3)
5. Place the jet covers and impellers/rotors in a sink.
6. Use a non-abrasive anbacterial cleaner to remove any visible residue, and rinse with
fresh water.
7. Use a non-abrasive anbacterial cleaner to clean the basin, jet cases, drain stopper, and
light casing, followed by a rinse with fresh water.
Fig. 1 Fig. 2 Fig. 3
Disinfection
1. Spray surface of the jet covers, impellers/rotors, and basin unl throughly coated with an
EPA-registered disinfectant.
2. Allow to set for the required disinfecon contact period (refer to manufacturer specs).
3. Rinse surfaces with fresh water.
Re-Assembly
1. Dry the jet covers, impellers/rotors, and basin.
2. Reinstall the impeller (magnet will hold it in place).
3. Reinstall the jet cover by placing it at the 10 o’clock posion. Maintain even pressure and
rotate jet cover to securely lock in place at the 3 or 9 o’clock posion.
NOTE: You will feel the cover click into place.
Jets will not run if not locked into place properly.
CAUTION
- Always refer to your state and local codes for specic cleaning requirements.
- NEVER USE abrasive cleaners on any surface area. Failure to comply can cause damage
and void your warranty.
Foot Bath Additives
Provide an enhanced pedicure experience with essenal oils, aromatherapy products, and other
addives, knowing all residue can be easily removed. The Sanijet® foot bath can be used with
most foot and skin care products, provided that the cleaning protocols are strictly followed.
Products NOT Recommended
• Silicate based bath addives/scrubs - may void warranty.
• High foam agents (use only low foam soluons).
• Abrasive cleaners that might damage the system components, and scratch/dull the basin
surface (major scratches will require professional renishing.
• To avoid discoloraon, products with petroleum disllates must not remain on surfaces.
CAUTION
DO NOT USE acetone, paint thinner, bleach, “Armor All” type cleaners, or industrial
cleaners. These will damage the upholstery’s protecve coang.
Do not place nail care products on the tub.
Extended exposure to chemicals can damage the basin, footpad, and/or upholstery.
Failure to comply with all cleaning instrucons can cause damage to your foot bath
and pedicure chair, and void the warranty.
DANGER: RISK OF ELECTRIC SHOCK
Always unplug this furnishing from the electrical outlet before cleaning.
Your pedicure chair is relavely maintenance free. However, to ensure your chair will connue
to funcon properly and keep its appearance, we recommend the following.
Category Care Recommendation
Upholstery
Remove day-to-day dirt and smudges with a mild soap and water soluon.
For tough stains and to disinfect, use a (100 to 1) water to bleach soluon.
Spray a damp cloth with the soluon to clean.
Aer each cleaning, gently wipe the upholstery with a damp cloth and clean
water, then allow upholstery to air dry before using or storing.
For more dicult stains, please contact your dealer or please call us directly
for guidance. For best results, use only the products suggested above.
Laminate &
Avonite
Never use abrasive cleaners. A mild liquid detergent and warm water will
clean soiled surfaces. To avoid discoloraon, cleaners containing petroleum
disllates must not remain on surfaces.
Electronics An-stac electronic aerosol dusters can be used to keep the surfaces of
electronic components, power cables, and plugs free of dust.
Lubricaon &
Mechanical
If necessary, lubricate wheel joints, casters, and other mechanical parts with
a light machine oil. Periodically check and ensure all visible bolts remain
ghtened.
Cleaning & Ongoing Maintenance

SECTION 4: CARE & MAINTENANCE
12
SECTION 4: CARE & MAINTENANCE
Electrical Specications
13
This helpful troubleshoong guide will provide you with informaon about how to recognize a
problem with your product, determine possible causes, and nd a soluon.
In the event your specic situaon is not covered in this guide, please contact Living Earth Cras
so our technical support department can assist you. Beyond the troubleshoong guide below, do
not aempt to repair the issue yourself. This can void your warranty.
Unauthorized service will not be covered. Please be sure to contact Living Earth Cras Customer
Service rst at [phone], [phone] Int’l.
Troubleshooting
Issue Solution
No Power/Not
Operang
1. Ensure the power cord is properly plugged into an operaonal GFCI
power supply/outlet.
2. Check GFCI reset and circuit breakers or fuses.
3. Ensure the outlet in your room is receiving power. This can be done
by plugging in a small appliance and turning it on.
No Power to
Jets/Jets not
Operang
1. Ensure the power cord is properly plugged into an operaonal GFCI
power supply/outlet.
2. Check GFCI reset and circuit breakers or fuses.
3. Check jet covers are locked into the 9 o’clock or 3 o’clock “run” posi-
on. You will feel the cover “click” into place.
4. Ensure magnec rotor/impeller is correctly installed in the case.
5. Reset the motors by unplugging the system, waing 5 seconds, then
plugging in again.
Excessive Noise
from Jets
1. Remove jet assembly and inspect for dirt buildup, debris, or damage.
2. Follow cleaning instrucons or replace if necessary.
Water Leakage
1. Check and ensure all visible bolts are ghtened.
2. Call a plumber to determine the source of the leak.
3. If the leak is from the jet system, contact LEC customer service.
Spec North America Europe/Asia
Input Voltage 120 VAC 220 VAC
Input Frequency 60 Hz 50 Hz
Total Consumpon
- All Opons 10.5 Amps Max 5.7 Amps Max
Consumpon -
Standard Contour 7.5 Amps Max 4.1 Amps Max
Consumpon -
Relaxor Addional 3 Amps (Max) Addional 1.6 Amps (Max)
Discharge Pump Specication
Motor Design Single-phase synchronous motor
Flow Rate (120V) 24 l/min at 0, 1 bar
Flow Rate (220V) 20 l/min at 0, 1 bar
Duty Cycle Connuous
Power Consumpon See electrical specicaon (next page)
Sanijet® Jet System Specication
Motor Design Single speed, electronic spherical DC motor with magnec rotor
impeller
Motor Materials Thermoplasc jet, motor, and case assembly; stainless steel rotor
impeller
Safety Features Safety shuto sensor, dry-run/thermal overload protecon
Power Consumpon See electrical specicaon (next page)

Owner’s Record
Warranty Information
Living Earth Cras (LEC) oers an industry best warranty against defects in materials, design,
and workmanship, to the original owner, as follows:
• Frame - lifeme warranty*
• Foam and upholstery covering - warranted for three (3) years
• Motors, controls, electronics - warranted for two (2) years, including parts and labor
• Accessories and opons - warranted for one (1) year, unless otherwise noted
LEC may repair or replace defecve components at our discreon. LEC will return the warranted
product, standard shipping pre-paid, to customers in the connental US. Internaonal customers
are responsible for any applicable dues and taxes, as well as all shipping charges inbound and
outbound. Normal wear and tear, and costs associated with maintenance procedures, and
damage caused by accident, misuse, improper maintenance, harsh operang environments or
neglect (which includes tears in the upholstery and damage caused by harsh chemical-based
cleaners) are not covered under this warranty. All warranes are limited to repair or replacement,
at LEC’s discreon, unless otherwise stated.
*Lifeme warranty applies to the original owner or for 5 years aer the model is disconnued,
or 5 years for private label chairs.
Does the Contour have backow prevenon?
Yes - see pages 10-11 in Installaon Manual for backow prevenon details.
Do I sll have to install backow prevenon on my main water supply line?
This is enrely dependent on your local and/or state codes. A licensed plumber with knowledge of
your local and/or state codes can answer this queson for you.
Do we need to install a p-trap?
Check with the licensed plumber performing the install. It is dependent on your drain locaon.
Can you provide a leer to my city inspector stang my electrical and/or plumbing setup is
acceptable?
Unfortunately not. In this document, we have provided all the informaon that a licensed plumber
and electrician would need to perform the proper install that adheres to local and state codes. Living
Earth Cras does not have knowledge of all local and state codes and therefore is not qualied to
advise on individual setup quesons. If an inspector has quesons about how your plumbing and/
or electrical is being set up, you will need to contact your plumber and/or electrician.
Does the Contour have GFI/GFCI built in?
There are no GFI/GFCIs built in to the system - we require a GFCI protected grounded circuit to
supply power to the Contour.
Frequently Asked Questions
14 15

Contact Us
Living Earth Crafts
3210 Executive Ridge
Vista, CA. 92081
[phone]
[phone] Int’l
[phone] fax
[email protected]
Hours of operation:
Monday - Friday
8:00 a.m. to 5 p.m. PST
Saturday - Sunday
Closed
Visit us online at: livingearthcrafts.com
Read our blog at: livingearthcrafts.com/blog
Join us on Facebook®