Living Spaces revive REV1500 User manual

REV1500 Wired Adjustable Base
OWNER’S MANUAL
Installation & Operation
Patent Pending
Warranty - 2-Year Parts and Labor on entire base
by LIVINGSPACES

Safety & Warranty Warnings 01
Parts List 03
REV1500 Electronics Quick Reference Guide 04
Installaon Guide 05
REV1500 Remote Control Instrucons 07
Synchronizing Two Bases 08
Headboard Bracket Installaon Guide 09
Troubleshoong 10
CONTENTS

Aenon: READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
If unable to understand warnings, cauons, and/or instrucons, contact the dealer or technical personnel if applicable, before aempng to
use the equipment. Otherwise, injury or damage may result.
SAFETY WARNINGS:
nasal masked type creates a possible fire hazard.
become entangled or damaged during normal operaon of the bed.
and unplug the bed immediately. Clean up spill and allow the area around bed to dry thoroughly before using the electric controls again. Do
not eat or drink hot liquids while operang the bed.
for their safety.
operang bed funcons.
Safety & Warranty Warnings
-01-

WARRANTY WARNING!
workings of these components are tampered with.
Product Rang:
Hospital Use Disclaimer:
Weight Limits:
-02-
RADIO FREQUENCY:2.4 GHz
FCC COMPLIANCE:
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.
To comply with the FCC RF exposure requirements, no change to the antenna or the device is permied. Any change to the antenna or the
device could result in the device exceeding the RF exposure requirement and void user’s right to operate the device.

-03-
Parts List
All electronics and components that need to be installed are located in boxes under the foundaon or
aached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.
WIRED REMOTE RETAINER BAR (2) POWER CORD
POWER SUPPLY BOX12" LEGS
King/CK Bed Legs & Boom Caps (8)
SPLITTER CABLE (included
with TXL or CKS size only
OPTIONAL EQUIPMENT (OPTIONAL)

-04-
REV1500 Electronics Quick Reference Guide
Head Motor
Remote
Power Cord
Power Supply

-05-
Installation Guide
Two people are required to set up the foundaon.
1. Open the shipping box, cut the ribbon securing accessory
boxes & maress retainer bar, and put them aside.
Li the folded bed frame unit out of the shipping carton
carefully, and then put it on a flat floor.
2. To install all six legs (see image A on the boom right), thread
the bolt of the leg to the nut on the foundaon frame, and ghten
by hand. DO NOT OVERTIGHTEN.
carton while the bed is in the flat posion.
3. Uncoil the input power cord and plug it into the power supply.
4. Uncoil the power cord and connect it to the power supply.
Nut on the frame is removable
and replaceable.
Please remove tape on the nut
to install legs.
WARNING

-06-
Head
Middle Leg on King/CK Size Only
Leg Posions
Foot
A
5. Carefully flip the foundaon over onto its legs.
Important: Two people are required to move the foundaon.
Do not drag across the floor. Do not rest frame on its side;
excessive pressure may damage the legs.
6. Insert the maress retainer bars into the grommets as shown.

-07-
REV1500 Remote Control Instructions
HEAD CONTROL
(Raise)
HEAD CONTROL
(Lower)

-08-
Synchronizing Two Bases
OVERVIEW
Two TXL or CKS bases may be placed next to each other to form a King or Cal King. Both sides can be operated independently with their own
remotes or, if desired, a single remote can be used with both bases. Using a single remote for both bases will result in the bases moving
jointly.
TO SYNC REMOTE TO TWO BASES:
STEP 2
Using the splier cable (included with TXL or CKS bases only) plug both
cables into each base (A & B). Finish by aaching the last cord to one
remote. The bases should now be controlled by one remote.
STEP 1
Ensure both bases (A & B) are plugged into a power source and both in the
flat posion.

-09-
Headboard Bracket Installation Guide
STEP 1
The headboard bracket will have 2 long slots
to accomodate any frame type. Align the
appropriate slots on the bracket with the
holes on the bed. Use bolts and nuts to
secure the bracket. Make sure the bolts are
ght.
STEP 4
You may now connect your headboard to the aachment plates using the remaining bolts and nuts to secure it to the brackets. The heads of the bolts
will face outward. Use a 1/2" (13 mm) socket and 1/2" (13 mm) wrench to ghten the bolts.
STEP 2
To put the T-Bracket 1 and
T-Bracket 2 together, you will
need (2) bolts and (2)nuts.
STEP 3
To put the T-Bracket and Headboard Bracket together,
you will need (2) bolts and (2) nuts. Slip the bolts
through the holes from T-Bracket to Headboard
Bracket with the head of bolt facing outward. Use 1/2''
(13mm) socket and 1/2'' (13mm) wrench to ghten the
bolts.
Headboard brackets are an oponal accessory and are not included.
A 1/2'' (13 mm) socket and 1/2'' (13 mm) crescent wrench are necessary to complete installaon.
HEADBOARD BRACKET COMPONENTS
(2) Headboard Brackets (2) T-Brackets 1 (2) T-Brackets 2 (16) Short Bolts (16) Nuts

-10-
Troubleshooting
In the event that the power foundaon fails to operate, assess the symptoms and possible soluons
provided in the chart below.
PROBLEM POSSIBLE SOLUTION
No features of the base will acvate.
Head secon will elevate, but will not return
to the flat posion.
Ensure that all wired connecons are secured below the bed base.
Unplug the power cord, wait 30 seconds and plug back in to reset electric components.
The surge protecon or the electrical outlet may be defecve. Test the outlet by plugging
in another working appliance.
Bed mechanism may be obstructed. Elevate bed and check for obstrucon. Remove
obstrucon.
Head secon may be too close to the wall.
The remote will not operate the base. Check to ensure that the remote control is secured completely and that the power cord is
plugged into the wall outlet.

NOTES:

by LIVINGSPACES
Customer Service: 1-855-430-8943
Serial No.